49.025.99 - Other materials

This document is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258.
This document has been prepared in accordance with EN 4500-003.

EN 4244 specifies the requirements relating to:Heat resisting alloy FE-PM1708 Vacuum arc remelted Hardened and tempered Bars a or D ≤ 200 mm 1 000 MPa ≤ Rm ≤ 1 140 MPa

This European Standard specifies the requirements relating to:
Heat resisting nickel base alloy (Ni-P101HT)
Cold worked and solution treated
Bar for machining for fasteners
3 mm ≤ D ≤ 50 mm
for aerospace applications.

This document specifies the requirements relating to:
Heat resisting nickel base alloy (NI-P101HT)
Cold worked and solution treated
Bars for machining for fasteners
3 mm ≤ D ≤ 50 mm
for aerospace applications.

This document specifies the requirements relating to:
Heat resisting alloy FE-PM1708
Vacuum arc remelted
Hardened and tempered
Bars
a or D ≤ 200 mm
1 000 MPa ≤ Rm ≤ 1 140 MPa
for aerospace applications.

This document specifies the requirements relating to:
Heat resisting alloy FE-PM1708
Vacuum arc remelted
As forged
Forging stock
De ≤ 300 mm
for aerospace applications.

This standard specifies the requirements relating to:Heat resisting nickel base alloy (NI-P100HT)Cold worked and softenedBar and wire for continuous forging or extrusion for fasteners3 mm ≤ D ≤ 30 mmfor aerospace applications.

This standard specifies the requirements relating to: Heat resisting alloy NI-PH 2601Solution treated and cold worked Bar for forged fasteners D ≤ 50 mm1 550 MPa ≤ Rm ≤ 1 830 MPa.

This document specifies the requirements relating to:
Heat resisting alloy NI-PH2601
Solution treated and cold worked
Bar for forged fasteners
D ≤ 50 mm
1 550 MPa ≤ Rm ≤ 1 830 MPa
for aerospace applications.

This document specifies the requirements relating to:
Heat resisting nickel base alloy (NI-P100HT)
Cold worked and softened
Bar and wire for continuous forging or extrusion for fasteners
3 mm ≤ D ≤ 30 mm

This European Standard defines the requirements for the preparation of forged test samples. Unless otherwise specified on the drawing, order, or inspection schedule, this document shall be applied when referenced in the relevant EN material standard or EN technical specification. This document applies to round products of ≥ 20 mm diameters or other shapes of equivalent cross-section.

This document defines the requirements for hexavalent chromium free anodizing of aluminium and
aluminium alloys for corrosion protection, bonding and painting.
Hard anodizing and plasma electrolytic anodizing (micro-arc oxidation) are not covered by this
document.
The purpose of this document is to give design, quality and manufacturing requirements. It does not give
complete in-house process instructions; these are given in the processors detailed process instructions.

This document defines the requirements for the preparation of forged test samples.
Unless otherwise specified on the drawing, order, or inspection schedule, this document shall be applied when referenced in the relevant EN material standard or EN technical specification.
This document applies to round products of ≥ 20 mm diameters or other shapes of equivalent cross-section.

This document specifies the requirements relating to:
Heat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al)
Solution treated and cold worked
Bar for forged fasteners
3 mm  ≤ D  ≤ 30 mm
for aerospace applications.

This European Standard specifies the requirements relating to:
Heat resisting alloy NI-PH2601
Solution treated and cold worked
Bar for forged fasteners
D ≤ 50 mm
1 270 MPa ≤ Rm ≤ 1 550 MPa
for aerospace applications.

This document specifies the requirements relating to:
Heat resisting nickel base alloy (Ni-P101HT)
Cold worked and softened
Bar and wire for continuous forging or extrusion for fasteners
3 mm ≤ D ≤ 30 mm
for aerospace applications.

This European Standard specifies two methods for the determination of the application time of sealants.

This European Standard specifies two methods for the determination of the application time of sealants.

This European Standard describes the preparation of panels with any desired fibre orientation of unidirectional orientated carbon fibre or fabric with thermosetting resins. The purpose of this standard is to describe recommended processes for the preparation of the panels from which test specimens subsequently are machined. Standard specimens prepared in this manner may be used either for evaluating the components i.e. the carbon reinforcement, finishes, resins, catalysts, curing agents, etc. or...view more

This standard specifies the requirements for glass fabric/phenolic resin preimpregnates. It shall be used together with EN 2833-1.