iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1127/C1127M-15(2023)

(Guide)

Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface

Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface

SIGNIFICANCE AND USE
4.1 This guide is divided into two sections which provide design and specification guidelines for the use of a cold liquid-applied elastomeric membrane with integral wearing surface for waterproofing building decks in building areas to be occupied by personnel, vehicles, or equipment.  
4.2 The intent of Sections 5 – 11, Design Considerations, is to provide information and design guidelines where a waterproofing membrane with integral wearing surface is to be used. The intent of the remaining sections is to provide minimum guide specifications for the use of the purchaser and the seller in contract documents.  
4.3 Where the state of the art is such that criteria for a particular condition is not as yet firmly established or has numerous variables that require consideration, reference is made to the applicable portion of Sections 5 – 11 that covers the particular area of concern. Section 16 describes the repair, rehabilitation, and replacement of the membrane.
SCOPE
1.1 This guide describes the design and installation of cold liquid-applied elastomeric waterproofing membrane systems that have an integral wearing surface. The cold liquid-applied elastomeric waterproofing membrane (membrane) to which this guide refers is specified in Specification C957/C957M.  
1.2 Concrete Slab-on-Grade—Waterproofing the upper surface of a concrete slab-on-grade presents special problems due to the possibility of negative hydrostatic pressure causing loss of bond to the substrate. Consideration of these problems is beyond the scope of this guide. Consult the membrane manufacturer for recommendations when this situation exists.  
1.3 The committee having jurisdiction for this guide is not aware of any similar ISO standard.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 15.4.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Aug-2023
ICS
83.140.99 - Other rubber and plastics products
Technical Committee
D08 - Roofing and Waterproofing
Drafting Committee
D08.25 - Liquid Applied Polymeric Materials Used for Roofing and Waterproofing Membranes that are Directly Exposed to the Weather
Current Stage
Ref Project

Relations

Refers
ASTM C755-20 - Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation
Effective Date
01-Mar-2020
Refers
ASTM D1079-20 - Standard Terminology Relating to Roofing and Waterproofing
Effective Date
01-May-2020

Buy Standard

ASTM C1127/C1127M-15(2023) - Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing SurfaceASTM C1127/C1127M-15(2023) - Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface
PreviousNext
Guide
ASTM C1127/C1127M-15(2023) - Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C1127/C1127M − 15 (Reapproved 2023)
Standard Guide for
Use of High Solids Content, Cold Liquid-Applied
Elastomeric Waterproofing Membrane with an Integral
1
Wearing Surface
This standard is issued under the fixed designation C1127/C1127M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This guide describes the design and installation of cold 2.1 ASTM Standards:
liquid-applied elastomeric waterproofing membrane systems C33/C33M Specification for Concrete Aggregates
that have an integral wearing surface. The cold liquid-applied C150/C150M Specification for Portland Cement
elastomeric waterproofing membrane (membrane) to which C330/C330M Specification for Lightweight Aggregates for
this guide refers is specified in Specification C957/C957M. Structural Concrete
C332 Specification for Lightweight Aggregates for Insulat-
1.2 Concrete Slab-on-Grade—Waterproofing the upper sur-
ing Concrete
face of a concrete slab-on-grade presents special problems due
C717 Terminology of Building Seals and Sealants
to the possibility of negative hydrostatic pressure causing loss
C755 Practice for Selection of Water Vapor Retarders for
of bond to the substrate. Consideration of these problems is
Thermal Insulation
beyond the scope of this guide. Consult the membrane manu-
C920 Specification for Elastomeric Joint Sealants
facturer for recommendations when this situation exists.
C957/C957M Specification for High-Solids Content, Cold
1.3 The committee having jurisdiction for this guide is not
Liquid-Applied Elastomeric Waterproofing Membrane
aware of any similar ISO standard.
With Integral Wearing Surface
C962 Standards Guide for Use of Elastomeric Joint Sealants
1.4 The values stated in either SI units or inch-pound units
3
are to be regarded separately as standard. The values stated in (Withdrawn 1992)
C1193 Guide for Use of Joint Sealants
each system may not be exact equivalents; therefore, each
system shall be used independently of the other. Combining D653 Terminology Relating to Soil, Rock, and Contained
values from the two systems may result in nonconformance Fluids
D1079 Terminology Relating to Roofing and Waterproofing
with the standard.
D1752 Specification for Preformed Sponge Rubber, Cork,
1.5 This standard does not purport to address all of the
and Recycled PVC Expansion Joint Fillers for Concrete
safety concerns, if any, associated with its use. It is the
Paving and Structural Construction
responsibility of the user of this standard to establish appro-
D2628 Specification for Preformed Polychloroprene Elasto-
priate safety, health, and environmental practices and deter-
meric Joint Seals for Concrete Pavements
mine the applicability of regulatory limitations prior to use.
4
2.2 U.S. Department of Commerce Standard:
For specific hazard statements, see 15.4.
Product Standard PS 1-74 Construction and Industrial Ply-
1.6 This international standard was developed in accor-
wood
dance with internationally recognized principles on standard-
5
2.3 American Concrete Institute (ACI) Standard:
ization established in the Decision on Principles for the
301-84 (1985) Specification for Structural Concrete for
Development of International Standards, Guides and Recom-
Buildings
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
1
This guide is under the jurisdiction of ASTM Committee D08 on Roofing and the ASTM website.
3
Waterproofing and is the direct responsibility of Subcommittee D08.25 on Liquid The last approved version of this historical standard is referenced on
Applied Polymeric Materials Used for Roofing and Waterproofing Membranes that www.astm.org.
4
are Directly Exposed to the Weather. Available from National Institute of Standards and Technology (NIST), 100
Current edition approved Sept. 1, 2023. Published September 2023. Originally Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
5
approved in 1989. Last previous edition approved in 2015 as C1127/C1127M – 15. Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington
DOI: 10.1520/C1127_C1127M-15R23. Hills, MI 48333-9094, http://www.concrete.org.
Copyright © ASTM International
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6262-23(Specification)
Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)

ABSTRACT
This specification covers requirements and methods of test for the material, dimensions, and workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from PAEK. The type of PAEK extruded, compression molded, and injection molded product may be categorized by type, grade and class depending on resin and filler compositions. Every type of PAEK shape may be categorized into one of several grades as follows: Grade 1 (general purpose) which is extruded, compression molded or injection molded product made using only 100% virgin PAEK resin and Grade 2 (recycle grade) which is extruded, compression molded or injection molded product made using any amount up to 100% of recycled thermoplastic PAEK. The type, class and grade is further differentiated based on dimensional stability. Different tests shall be conducted in order to determine the following properties of PAEK: tensile stress at break, elongation at break, tensile modulus, dimensional stability, lengthwise camber and widthwise bow, squareness, flexural modulus, and Izod impact.
SCOPE
1.1 This specification covers requirements for the PAEK materials used and the requirements and methods of test for the dimensions, workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from PAEK. PAEK is a family of thermoplastic materials that differ in properties (see Section 3).  
1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications are described by using the classification system given in Section 4.  
1.3 This specification allows the use of key clad plastics (see Section 4).  
1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1.  
1.5 The following precautionary caveat pertains only to the test method portion Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D2463-23(Test Method)
Standard Test Method for Drop Impact Resistance of Blow-Molded Thermoplastic Containers

SIGNIFICANCE AND USE
5.1 These procedures provide a means to assess the drop impact resistance of the group or lot of blown containers from which the test specimens were selected.  
5.2 It is acceptable to use these procedures for routine inspection purposes.  
5.3 These procedures will evaluate the combined effect of construction, materials, and processing conditions on the impact resistance of the blown containers.  
5.4 Before proceeding with this test method, reference the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the materials specification shall take precedence over those mentioned in this test method. If there are no material specifications, then the default conditions apply.
SCOPE
1.1 This test method provides a means to assess the drop impact resistance of water-filled, blow-molded thermoplastic containers, which is a summation of the effects of material, manufacturing conditions, container design, and perhaps other factors.  
1.2 Two procedures are provided as follows:  
1.2.1 Procedure A, Static Drop Height Method—This procedure is particularly useful for quality control since it is quick.  
1.2.2 Procedure B, Bruceton Staircase Method—This procedure is used to determine the mean failure height and the standard deviation of the distribution.  
1.3 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are for information only.  
Note 1: There is no known ISO equivalent to this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C722-18(2023)(Specification)
Standard Specification for Chemical-Resistant Monolithic Floor Surfacings

ABSTRACT
This specification covers the requirements for aggregate-filled, resin-based, monolithic surfacing for use over concrete floors in areas where chemical resistance and the protection of concrete are required. The application methods for these floor surfacing shall include troweled, broadcast, slurry broadcast, self-leveling, sprayed, and reinforced. The resin chemistries include epoxy, urethane, polyester, and vinyl ester. Service conditions such as chemical exposure; traffic, and temperature conditions shall be considered in selecting the flooring system. The flooring material shall conform to the physical properties, chemical resistance, and performance requirements of the specific flooring system. The following methods shall be performed for the specific system to be tested: chemical resistance of mortars, grouts, and monolithic surfacing; test method for tensile strength of chemical-resistant mortars, grouts, and monolithic surfacing; test method for absorption of chemical-resistant mortars, grouts, and monolithic surfacing; test method for compressive strength of chemical-resistant mortars, grouts, monolithic surfacing, and polymer concretes; test method for flexural strength and modulus of elasticity of chemical-resistant mortars, grouts, monolithic surfacing, and polymer concretes; test method for determining the static coefficient of friction of ceramic tile and other like surfaces by horizontal dynamometer pull-meter method.
SCOPE
1.1 This specification covers the requirements for aggregate-filled, resin-based, monolithic surfacings for use over concrete floors in areas where chemical resistance and the protection of concrete are required.  
1.2 The application methods for these floor surfacings include troweled, broadcast, slurry broadcast, self-leveling, sprayed, and reinforced. The resin chemistries include epoxy, urethane, polyester, and vinyl ester.  
1.3 Floor surfacings used as vessel linings are excluded from this specification.  
1.4 The values stated in SI units are to be regarded as the standard. The values in parenthesis are provided for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D707-15(2023)(Specification)
Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB)

ABSTRACT
This specification covers requirements for plasticized cellulose acetate butyrate thermoplastic compounds suitable for injection molding and extrusion. These compounds have a butyryl content less than 38 % and an acetyl content less than 15 % and may or may not contain dyes and pigments. This specification does not include special materials compounded for special applications. Cellulosic plastic materials, being thermoplastic, are reprocessable and recyclable. This specification allows for the use of those cellulosic materials, provided that all specific requirements of this specification are met. Test specimens of the thermoplastic compounds shall conform to the prescribed specific gravity, tensile stress at yield, flexural modulus, Izod impact strength, water absorption and weight loss on heating. The materials shall also be subject to color-visual, color-quantitative, and plasticizer content analysis.
SCOPE
1.1 This classification system covers requirements for plasticized cellulose acetate butyrate thermoplastic compounds suitable for injection molding and extrusion. These compounds have a butyryl content less than 38 % and an acetyl content less than 15 % and can contain dyes and pigments. This classification system does not include special materials compounded for special applications. Cellulosic plastic materials, being thermoplastic, are reprocessable and recyclable. This classification system allows for the use of those cellulosic materials, provided that all specific requirements of this classification system are met.  
1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are specified by using the suffixes as given in Section 5.  
1.3 This classification system and subsequent line call out (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and performance required of the part, environment to which it will be exposed, fabrication process to be employed, costs involved, and inherent properties of the material other than those covered by this classification system.  
1.4 The values stated in SI units are to be regarded as standard.  
1.5 The following safety hazards caveat pertains only to the test method portion, Section 12, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D7258-23(Specification)
Standard Specification for Polymeric Piles

ABSTRACT
This specification establishes the physical and performance requirements for round and rectangular cross-section polymeric piles in axial and lateral load-bearing applications including, by not limited to, marine, waterfront, and corrosive environments. It does not apply to individual polymeric pile products, sheet piles, and other mechanically connected polymeric pile products using inter-locking systems. Covered here are six types of polymeric piles that are fabricated from materials that may be virgin, recycled, or both, as long as the finished product meets all of the criteria specified herein. These types are: Type I, polymeric only; Type II, polymeric with reinforcement in the form of chopped, milled or continuous fiber or mineral; Type III, polymeric with reinforcement in the form of metallic bars, cages, or shapes; Type IV, polymeric with reinforcement in the form of non-metallic bars or cages; Type V, polymeric composite tube with a concrete core; and Type VI, any other polymeric piling meeting the requirements stated herein and not otherwise described by Types I through V. The polymeric tiles shall adhere to specified physical attributes such as size, cross-sectional shape, length, straightness, placement of reinforcement, and surface conditions. The performance requirements which pile specimens shall conform to include creep rupture, serviceability, flexural properties, shear strength, bearing strength, design flexural stiffness, energy absorption, compressive strength, combined stresses, dimensional stability (thermal expansion), hygrothermal cycling, and flame spread index.
SCOPE
1.1 This specification addresses the use of round and rectangular cross-section polymeric piles in axial and lateral load-bearing applications, including but not limited to marine, waterfront, and corrosive environments.  
1.2 This specification is only applicable to individual polymeric pile products. Sheet pile and other mechanically connected polymeric pile products using inter-locking systems, are not part of this specification.  
1.3 The piling products considered herein are characterized by the use of polymers, whereby (1) the pile strength or stiffness requires the inclusion of the polymer, or (2) a minimum of fifty percent (50 %) of the weight or volume is derived from the polymer. The type classifications of polymeric piles described in Section 4 show how they can be reinforced by composite design for increased stiffness or strength.  
1.4 This specification covers polymeric piles fabricated from materials that are virgin, recycled, or both, as long as the finished product meets all of the criteria specified herein. Diverse types and combinations of inorganic filler systems are permitted in the manufacturing of polymeric piling products. Inorganic fillers include such materials as talc, mica, silica, wollastonite, calcium carbonate, etc. Pilings are often placed in service where they will be subjected to continuous damp or wet exposure conditions. Due to concerns of water sensitivity and possible affects on mechanical properties in such service conditions, organic fillers, including lignocellulosic materials such as those made or derived from wood, wood flour, flax shive, rice hulls, wheat straw, and combinations thereof, are not permitted in the manufacturing of polymeric piling products.  
1.5 The values are stated in inch-pound units as these are currently the most common units used by the construction industry.  
1.6 Polymeric piles under this specification are designed using design stresses determined in accordance with Test Methods D6108, D6109, and D6112 and procedures contained within this specification unless otherwise specified.  
1.7 Although in some instances it will be an important component of the pile design, frictional properties are currently beyond the scope of this document.  
1.8 Criteria for design are included as part of this specification for polymeric piles. Certain Types and...

  • Technical specification
    18 pages
    English language
    sale 15% off
  • Technical specification
    18 pages
    English language
    sale 15% off
ASTM
ASTM D7486-22(Test Method)
Standard Test Method for Measurement of Fines and Dust Particles on Plastic Pellets by Wet Analysis

SIGNIFICANCE AND USE
5.1 Molding and extruding plastic pellets require dust free, dry pellets to prevent processing problems. Plastic producers try to remove the dust and streamers with dust removal systems prior to packaging and loading. How to accurately measure dust and streamer content in plastic pellets is an important quality control issue.  
5.2 Particle size analysis is used to determine a percentage of particle size distribution from a representative sample of the whole. In terms of size analysis concerning plastic pellets, sieving is used to determine the dust content in the range of 500 to 2000 micron. Test Method D1921, Test Method B, is used to determine this type of particle sizing.  
5.3 After dry sieve analysis, particles smaller than 500 microns need to be analyzed by wet method. A fresh sample shall be used for wet analysis. This test method allows washing down the fines attached to the pellets by electrostatic forces.  
5.4 The wet analysis provides accurate quantification of small to large amounts of fines, negating static effects, and eliminating detrimental effects of mechanical agitation. A wet analysis must be employed to accurately quantify lower PPM dust levels in plastic pellets.
SCOPE
1.1 This test method measures the amount of fine particles adhered on plastic pellets or granules in which they are commonly produced and supplied. The lower limit of this test method is restricted only by the porosity of the filter disc used to capture the particle size being quantified.  
1.2 The wet analysis technique allows for separation and collection of statically charged particles by liquid wash and filtration methods. This must be performed under standard laboratory conditions.  
1.3 The values stated in SI units are to be regarded as standard.  
1.4 This test method describes an essential practice to check the quality of plastics once the production cycle is terminated and to evaluate the performance of pellet cleaning systems or of the special pneumatic conveying systems for the distinct size fractions below 500 micron only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F905-04(2022)(Practice)
Standard Practice for Qualification of Polyethylene Saddle-Fused Joints

SIGNIFICANCE AND USE
3.1 The tests described in this practice are intended to present a method of satisfying the requirements of DOT CFR Title 49, Parts 192.283 and 192.285.  
3.2 The sustained pressure test is intended to meet the burst test requirements of Part 192.283.  
3.3 The impact resistance test is intended to meet the force requirements of Part 192.283 as follows:  
3.3.1 “. . . For procedures intended for lateral pipe connections, subject a specimen joint made from pipe sections joined at right angles according to the (joining) procedure to a force on the lateral pipe until failure occurs in the specimen. If failure initiates outside the joint area, the (joining) procedure qualifies for use.”
SCOPE
1.1 This practice describes test criteria suitable for qualification of polyethylene saddle-fused joints. These tests may be conducted by suppliers or users to qualify saddle-fused joints in accordance with the requirements found in the Department of Transportation (DOT) Code of Federal Regulations (CFR) Title 49, Part 192.283. At the discretion of the end user, these tests may also be conducted by users to qualify personnel making saddle fusion joints per DOT CFR 49, Part 192.285.  
1.2 The impact resistance test described is a nonstandard test. This is not the only test that may be used to qualify saddle fusion joints per DOT regulations.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversion to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5336-22(Specification)
Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials

ABSTRACT
This specification covers the classification, testing, and requirements of polyphthalamide (PPA) materials, both virgin and recycled, suitable for injection molding. This specification is intended to be a means of calling out plastics materials used in the fabrication of end items or parts, and not for the selection of materials. The materials are classified into groups according to crystallinity, and are further subdivided into classes and grades as specified. Materials shall be sampled, prepared, and conditioned appropriately for testing, for which specimens shall conform to specified values of the following requirements: inherent viscosity; melting temperature; glass transition; tensile strength; flexural strength and modulus; Izod impact strength; deflection temperature; and moisture.
SCOPE
1.1 This classification system covers polyphthalamide (PPA) materials suitable for injection molding.  
1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5.  
1.3 This classification system allows for the use of recycled materials provided that all specification requirements are met.  
1.4 This classification system is intended to be a means of calling out plastics materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastics field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system.  
1.5 The values stated in SI units are to be regarded as the standard (see IEEE/ASTM SI-10). The values given in parentheses are for information only.  
1.6 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 11.7.1.
Note 1: There is no known ISO equivalent to this standard. ISO 16396-1/-2 for polyamides may also be used to describe and classify these PPA materials, but the technical content is significantly different.
Note 2: ASTM Standard D6779 on polyamide materials also includes PPA materials in its coverage of various polyamide chemistries. This standard gives additional information for classification and specification for PPA compositions classified as Group 10 (PA6T/66), Group 12 (PA6T/6I/66) and Group 13 (PA6T/6I) in ASTM Standard D6779 and includes provisions for other PPA compositions to utilize the classification presented.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM D1562-22(Specification)
Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP)

SCOPE
1.1 This classification system covers requirements for plasticized cellulose acetate propionate thermoplastic compounds suitable for injection molding and extrusion. These compounds have a propionyl content less than 48 % and an acetyl content less than 3 % and can contain dyes and pigments. Cellulosic plastic materials, being thermoplastic, are reprocessable and recyclable. This classification system allows for the use of those cellulosic materials, provided that all specific requirements of this classification system are met.  
1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are specified by using the suffixes as given in Section 5.  
1.3 This classification system and subsequent line call out specification are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and performance required of the part, environment to which it will be exposed, fabrication process to be employed, costs involved, and inherent properties of the material other than those covered by this classification system.  
1.4 The values stated in SI units are to be regarded as standard.  
1.5 The following safety hazards caveat pertains only to the test method portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D3294-22(Specification)
Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes

ABSTRACT
This specification establishes the requirements and test methods for the material, dimensions, and workmanship, and the physical and electrical properties of molded sheet manufactured from polytetrafluoroethylene (PTFE) resin molding materials and molded basic shapes made from resin molding and extrusion materials. The sheet or molded basic shape shall be made from unpigmented PTFE and shall be free from foreign matters. Each of the samples shall undergo visual and dimensional inspection to verify their compliance with the standard requirements. The specimens shall conform to the following physical and electrical property requirements: tensile strength; elongation; dielectric strength; specific gravity; porosity; and melting point. Examination for internal defects shall also be conducted to ensure that the specimens are free from microscopic cracks, voids, inclusions, and other surface defects that might affect the serviceability of the materials.
SCOPE
1.1 This specification establishes requirements and methods of test for the material, dimensions, and workmanship, and the physical and electrical properties of molded sheet in minimum thicknesses of 0.794 mm (1/32 in.) manufactured from PTFE resin molding materials defined in Specification D4894.  
1.2 This specification also establishes requirements for molded basic shapes made from molding materials. This specification is for products 300 mm (12 in.) or less in a dimension parallel to and 12.7 mm (0.5 in.) or greater in the dimension perpendicular to the direction of the applied molding pressure.  
1.3 The values stated in SI units are to be regarded as the standard.  
1.4 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Special attention is called to 13.2, 13.3, 13.6, 13.8, and A1.  
Note 1: There is no known ISO equivalent to this standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off