ASTM A369/A369M-00

Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service

SCOPE
1.1 This specification covers heavy-wall carbon and alloy steel pipe (Note 1) made from turned and bored forgings and is intended for high-temperature service. Pipe ordered under this specification shall be suitable for bending and other forming operations and for fusion welding. Selection will depend on design, service conditions, mechanical properties and high-temperature characteristics.
Note 1—The use of the word "pipe" throughout the several sections of this specification is used in the broad sense and intended to mean pipe headers, or leads.
Note 2—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as "nominal diameter," "size," and "nominal size."
1.2 Several grades of ferritic steels are covered. Their compositions are given in Table 1.
1.3 Supplementary requirements (S1 to S6) of an optional nature are provided. These supplementary requirements call for additional tests to be made, and when desired shall be so stated in the order, together with the number of such tests required.
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.

General Information

• Status: Historical
• Publication Date: 09-Mar-2002
• ICS: 23.040.10 - Iron and steel pipes
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.10 - Stainless and Alloy Steel Tubular Products

Relations

• Replaced By: ASTM A369/A369M-01 - Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service
• Effective Date: 10-Mar-2002
• Referred By: ASTM A999/A999M-23 - Standard Specification for General Requirements for Alloy and Stainless Steel Pipe
• Effective Date: 10-Mar-2002

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: A 369/A 369M – 00 An American National Standard
Standard Specification for
Carbon and Ferritic Alloy Steel Forged and Bored Pipe for
1
High-Temperature Service
This standard is issued under the fixed designation A 369/A 369M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope E 381 Method of Macroetch Testing, Inspection, and Rating
2
Steel Products, Comprising Bars, Billets, Blooms, and
1.1 This specification covers heavy-wall carbon and alloy
4
Forgings
steel pipe (Note 1) made from turned and bored forgings and is
2.2 ASME Boiler and Pressure Vessel Code:
intended for high-temperature service. Pipe ordered under this
5
Section 1X Welding Qualifications
specification shall be suitable for bending and other forming
2.3 ANSI Standard:
operations and for fusion welding. Selection will depend on
6
B 46.1 Surface Texture
design, service conditions, mechanical properties and high-
temperature characteristics.
3. Ordering Information
NOTE 1—The use of the word “pipe” throughout the several sections of
3.1 Orders for material to this specification should include
this specification is used in the broad sense and intended to mean pipe
the following, as required, to describe the desired material
headers, or leads.
adequately:
NOTE 2—The dimensionless designator NPS (nominal pipe size) has
3.1.1 Quantity (feet, centimetres, or number of lengths),
been substituted in this standard for such traditional terms as “nominal
3.1.2 Name of material (forged and bored pipe),
diameter,” “size,” and “nominal size.”
3.1.3 Grade (Table 1),
1.2 Several grades of ferritic steels are covered. Their
3.1.4 Size (inside diameter and minimum wall thickness),
compositions are given in Table 1.
3.1.5 Length (Permissible Variations in Length Section of
1.3 Supplementary requirements (S1 to S6) of an optional
Specification A 999/A 999M),
nature are provided. These supplementary requirements call for
3.1.6 End finish (13),
additional tests to be made, and when desired shall be so stated
3.1.7 Optional requirements (Sections 8, Supplementary
in the order, together with the number of such tests required.
Requirements S1 to S6; 13.2),
1.4 The values stated in either inch-pound units or SI units
3.1.8 Test report required (Certification Section of Specifi-
are to be regarded separately as standard. Within the text, the
cation A 999/A 999M),
SI units are shown in brackets. The values stated in each
3.1.9 Specification designation, and
system are not exact equivalents; therefore, each system must
3.1.10 Special requirements or exceptions to this specifica-
be used independently of the other. Combining values from the
tion.
two systems may result in nonconformance with the specifi-
cation. The inch-pound units shall apply unless the “M”
4. General Requirements
designation of this specification is specified in the order.
4.1 Material furnished under this specification shall con-
form to the applicable requirements of the current edition of
2. Referenced Documents
Specification A 999/A 999M, unless otherwise provided
2.1 ASTM Standards:
herein.
A 999/A 999M Specification for General Requirements for
3
Alloy and Stainless Steel Pipe
5. Materials and Manufacture
E 290 Test Method for Semi-Guided Bend Test for Ductility
5.1 Discard:
4
of Metallic Materials
5.1.1 A sufficient discard shall be made from each ingot to
secure freedom from injurious defects. The steel shall have a
homogeneous structure.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
5.2 Manufacture:
Stainless Steel and Related Alloys, and is the direct responsibility of Subcommittee
A01.10 on Stainless and Alloy Steel Tubular Products. 5.2.1 Material for forging shall consist of ingots or of
Current edition approved May 10, 2000. Published August 2000. Originally
published as A 369/A 369M – 53 T. Last previous edition A 369/A 369M – 92.
2 5
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Available from ASME International, Three Park Avenue, New York, NY
cation SA-369 in Section II of that Code. 10016–5990.
3 6
Annual Book of ASTM Standards, Vol 01.01. Available from American National Standards Institute, 11 West 42nd St., 13th
4
Annual Book of ASTM Standards, Vol 03.01. Floor, New York, NY 10036.
Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 369/A 369M
TABLE 1 Chemical Requirements
Grade Composition, %
FPA FPB FP1 FP2
Carbon 0.25 max 0.30 max 0.10–0.20 0.10–0.20
Manganese 0.27–0.93 0.29–1.06 0.30–0.80 0.30–0.61
Phospho
...