Standard Specification for Seamless and Welded Carbon Steel Water-Well Pipe

SCOPE
1.1 This specification covers four specific types of plain end or threaded and coupled carbon steel pipe for use in water wells.
1.2 Each type of water well pipe shall conform to the following methods of manufacture and grade as specified on the purchase order:
1.2.1 Type I, Drive Pipe—Seamless or electric-resistance-welded, Grades A and B.
1.2.2 Type II, Water-Well Reamed and Drifted Pipe—Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded.
1.2.3 Type III, Driven Well Pipe—Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded.
1.2.4 Type IV, Water-Well Casing Pipe—Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded.
1.3 The values stated in inch-pound units are to be regarded as the standard.
Note 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as "nominal diameter," "size," and "nominal size."

General Information

Status
Historical
Publication Date
09-Oct-1996
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM A589-96(2001) - Standard Specification for Seamless and Welded Carbon Steel Water-Well Pipe
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
Designation: A 589 – 96 (Reapproved 2001)
Standard Specification for
1
Seamless and Welded Carbon Steel Water-Well Pipe
This standard is issued under the fixed designation A589; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
4
1. Scope 5L Specification for Line Pipe
1.1 Thisspecificationcoversfourspecifictypesofplainend
3. Terminology
or threaded and coupled carbon steel pipe for use in water
3.1 Definitions of Terms Specific to This Standard:
wells.
3.1.1 defect—an imperfection of sufficient size or magni-
1.2 Each type of water well pipe shall conform to the
tude to be cause for rejection.
following methods of manufacture and grade as specified on
3.1.2 imperfection—any discontinuity or irregularity found
the purchase order:
in the pipe.
1.2.1 Type I, Drive Pipe—Seamless or electric-resistance-
welded, Grades A and B.
4. Ordering Information
1.2.2 Type II, Water-Well Reamed and Drifted Pipe—
4.1 Orders for material to this specification should include
Seamless or electric-resistance-welded, Grades A and B, or
the following, as required to describe the desired material
furnace-butt welded.
adequately:
1.2.3 Type III, Driven Well Pipe—Seamless or electric-
4.1.1 Quantity (feet or number of lengths),
resistance-welded, Grades A and B, or furnace-butt welded.
4.1.2 Name of material or type number (see 1.2),
1.2.4 Type IV, Water-Well Casing Pipe—Seamless or
4.1.3 Method of manufacture (furnace-butt welded, seam-
electric-resistance-welded, Grades A and B, or furnace-butt
less, or electric-resistance-welded),
welded.
4.1.4 Grade (A or B for seamless or electric-resistance
1.3 The values stated in inch-pound units are to be regarded
welded),
as the standard.
4.1.5 Finish (black or galvanized),
NOTE 1—The dimensionless designator NPS (nominal pipe size) has
4.1.6 Dimensions (NPS or outside diameter and wall thick-
been substituted in this standard for such traditional terms as “nominal
ness,orboth,forTypesI,II,andIII.Outsidediameterandwall
diameter,” “size,” and “nominal size.”
thickness for Type IV),
4.1.7 End finish (plain end or threaded and coupled),
2. Referenced Documents
4.1.8 Coupling class for Type III (standard pipe, line pipe,
2.1 ASTM Standards:
or reamed and drifted pipe coupling),
A53/A53M Specification for Pipe, Steel, Black and Hot-
4.1.9 Coupling make-up (hand tight or power tight),
2
Dipped, Zinc-Coated Welded and Seamless
4.1.10 Length (required random range length or special
A370 TestMethodsandDefinitionsforMechanicalTesting
lengths),
3
of Steel Products
4.1.11 Specification designation, and
A 751 Test Methods, Practices, and Terminology for
4.1.12 Special requirements.
3
Chemical Analysis of Steel Products
A865 Specification for Threaded Couplings, Steel, Black
5. Materials and Manufacture
orZincCoated(Galvanized),WeldedorSeamless,forUse
5.1 The steel for both seamless and welded pipe shall be
2
in Steel Pipe Joints
made by one of the following processes: open-hearth, electric-
2.2 API Standard:
furnace, or basic-oxygen.
5.2 Steel may be cast in ingots or may be strand cast.When
1
steels of different grades are sequentially strand cast, identifi-
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel,
Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee
cation of the resultant transition material is required. The
A01.09 on Carbon Steel Tubular Products.
Current edition approved Oct. 10, 1996. Published October 1997. Originally
published as A589–68. Last previous edition A589–95a.
2 4
Annual Book of ASTM Standards, Vol 01.01. Available from American Petroleum Institute, 1220 L. St., NW, Washington,
3
Annual Book of ASTM Standards, Vol 01.03. DC 20005.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
A 589 – 96 (2001)
producer shall remove the transition material by any estab- Samples for chemical analysis and the methods of analysis
lished procedure that positively separates the grades. shall conform to the requirements of Test Methods, Practices,
andTerminologyA751.The chemical composition thus deter-
6. Chemical Composition
mined shall conform to the requirements specified in 6.1.
6.1 Thesteelshallconformtothefollowingrequirementsas
8.2 If the analysis of either pipe does not conform to the
to chemical composition:
requirements of 6.1, analysis shall be made on ad
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.