ASTM B897-13
(Specification)Standard Specification for Configuration of Zinc and Zinc Alloy Jumbo, Block, Half Block, and Slab Ingot
Standard Specification for Configuration of Zinc and Zinc Alloy Jumbo, Block, Half Block, and Slab Ingot
ABSTRACT
This specification covers zinc and zinc alloy jumbo and block ingots meeting dimensional requirements. Zinc jumbo and block ingot specifications shall include dimension definition and limits in dimension. Jumbo or block ingots, or both, shall be reasonably free from dross, cracks, adhering foreign matter, undue surface oxide, and any "flash" that would interfere with handling and use.
SCOPE
1.1 This specification covers zinc and zinc alloy jumbo, block, half block, and slab ingot meeting dimensional requirements.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B897 −13
Standard Specification for
Configuration of Zinc and Zinc Alloy Jumbo, Block, Half
1
Block, and Slab Ingot
This standard is issued under the fixed designation B897; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Terminology
1.1 This specification covers zinc and zinc alloy jumbo,
3.1 Terms shall be defined in accordance with Terminology
block, half block, and slab ingot meeting dimensional require- B899.
ments.
3.2 Definitions of Terms Specific to This Standard:
1.2 The values stated in inch-pound units are to be regarded
3.2.1 jumbo ingot, n—large casting of zinc or zinc alloy,
as standard. The values given in parentheses are mathematical
having through holes for chains, designed for handling by
conversions to SI units that are provided for information only
mechanical equipment, with a nominal weight of 2400 pounds,
and are not considered standard.
which is also referred to as a jumbo or strip jumbo.
1.3 This standard does not purport to address all of the
3.2.2 block ingot, n—large casting of zinc or zinc alloy,
safety concerns, if any, associated with its use. It is the
having lift pockets, designed for handling by mechanical
responsibility of the user of this standard to become familiar
equipment, with a nominal weight of 2400 pounds, which is
with all hazards including those identified in the appropriate
also referred to as a block.
Material Safety Data Sheet (MSDS) for this product/material
3.2.3 half block ingot, n—large casting of zinc or zinc alloy,
as provided by the manufacturer, to establish appropriate
having lift pockets, designed for handling by mechanical
safety and health practices, and determine the applicability of
equipment, with a nominal weight of 1200 pounds, which is
regulatory limitations prior to use.
also referred to as half block.
2. Referenced Documents 3.2.4 slab ingot, n—smaller casting of zinc or zinc alloy
designed for manual handling, but often handled by mechani-
2.1 The following standards of the issue in effect on date of
cal equipment, with a nominal weight of 55 pounds, which is
order acceptance, form a part of this specification to the extent
also referred to as slab.
referenced herein:
3.2.5 slab bundle, n—arrangement of typically 40 slab
2
2.2 ASTM Standards:
ingots strapped with metal or other binding, with nominal
B6 Specification for Zinc
weightof2200pounds,whichisalsoreferredtoasbundle.The
B852 Specification for Continuous Galvanizing Grade
bundle may be stacked on a wood or other skid.
(CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet
Steel
4. Ordering Information
B899 Terminology Relating to Non-ferrous Metals and Al-
loys 4.1 Orders for jumbo, block, half block, or slab ingots under
B949 Specification for General Requirements for Zinc and
this specification shall include the following information in
Zinc Alloy Products addition to the appropriate information specified in Specifica-
E29 Practice for Using Significant Digits in Test Data to tion B949, Section 4:
Determine Conformance with Specifications 4.1.1 Type of ingot (Jumbo, Type 1 Block, Type 2 Block,
Half Block Type 1, Half Block Type 2, or Slab).
4.1.2 Order may stipulate dimensions, or tolerances, or
1
This specification is under the jurisdiction of ASTM Committee B02 on
both, not meeting this specification only upon mutual written
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.04 on Zinc and Cadmium.
agreement between purchaser and producer.
Current edition approved Dec. 1, 2013. Published January 2014. Originally
approved in 1999. Last previous edition approved in 2010 as B897 – 10. DOI:
5. Materials and Manufacture
10.1520/B0897-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1 The producer shall use care to have each lot of zinc
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
metal or zinc alloy jumbo, block, half block, or slab ingots be
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. of as uniform quality as possible.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B897−13
TABLE 1 Zinc Jumbo Ingot Specification TABLE 3 Zinc Half Block Ingot Specification
Weight 2400 ± 100 lb (1089 ± 45 kg) Weight1200±50lb(545±23kg)
Table of Dimensions Table of Dimensions
Drawing Drawing
Identification Dimension Definition Dimension, in. Dimension, mm Identific
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B897 − 10 B897 − 13
Standard Specification for
Configuration of Zinc and Zinc Alloy Jumbo Block and Half
1
Block Jumbo, Block, Half Block, and Slab Ingot
This standard is issued under the fixed designation B897; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers zinc and zinc alloy jumbo, block, and half block half block, and slab ingot meeting dimensional
requirements.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 The following standards of the issue in effect on date of order acceptance, form a part of this specification to the extent
referenced herein:
2
2.2 ASTM Standards:
B6 Specification for Zinc
B852 Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel
B899 Terminology Relating to Non-ferrous Metals and Alloys
B949 Specification for General Requirements for Zinc and Zinc Alloy Products
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
3. Terminology
3.1 Terms shall be defined in accordance with Terminology B899.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 jumbo ingot, n—large casting of zinc or zinc alloy, having through holes for chains, designed for handling by mechanical
equipment, with a nominal weight of 2400 pounds, which is also referred to as a jumbo or strip jumbo.
3.2.2 block ingot, n—large casting of zinc or zinc alloy, having lift pockets, designed for handling by mechanical equipment,
with a nominal weight of 2400 pounds, which is also referred to as a block.
3.2.3 half block ingot, n—large casting of zinc or zinc alloy, having lift pockets, designed for handling by mechanical
equipment, with a nominal weight of 1200 pounds, which is also referred to as half block.
3.2.4 slab ingot, n—smaller casting of zinc or zinc alloy designed for manual handling, but often handled by mechanical
equipment, with a nominal weight of 55 pounds, which is also referred to as slab.
3.2.5 slab bundle, n—arrangement of typically 40 slab ingots strapped with metal or other binding, with nominal weight of 2200
pounds, which is also referred to as bundle. The bundle may be stacked on a wood or other skid.
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.04 on Zinc
and Cadmium.
Current edition approved April 1, 2010Dec. 1, 2013. Published April 2010January 2014. Originally approved in 1999. Last previous edition approved in 20092010 as
B897 - 09.B897 – 10. DOI: 10.1520/B0897-10.10.1520/B0897-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B897 − 13
4. Ordering Information
4.1 Orders for jumbo, block, or half block half block, or slab ingots under this specification shall include the following
information in addition to the appropriate information specified in Specification B949, Section 4:
4.1.1 Type of ingot (Jumbo, Type 1 Block, Type 2 Block, Half Block Type 1, or Half Block Type 2).2, or Slab).
4.1.2 Order may stipulate dimensions, or tolerances, or both, not meeting this specification only upon mutual written agreement
between purchaser and producer.
5. Materials and Manufacture
5.1 The produc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.