ASTM B897-10
(Specification)Standard Specification for Configuration of Zinc and Zinc Alloy Jumbo Block and Half Block Ingot
Standard Specification for Configuration of Zinc and Zinc Alloy Jumbo Block and Half Block Ingot
ABSTRACT
This specification covers zinc and zinc alloy jumbo and block ingots meeting dimensional requirements. Zinc jumbo and block ingot specifications shall include dimension definition and limits in dimension. Jumbo or block ingots, or both, shall be reasonably free from dross, cracks, adhering foreign matter, undue surface oxide, and any "flash" that would interfere with handling and use.
SCOPE
1.1 This specification covers zinc and zinc alloy jumbo, block, and half block ingot meeting dimensional requirements.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B897 −10
StandardSpecification for
Configuration of Zinc and Zinc Alloy Jumbo Block and Half
1
Block Ingot
This standard is issued under the fixed designation B897; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Terminology
1.1 This specification covers zinc and zinc alloy jumbo, 3.1 Terms shall be defined in accordance with Terminology
block, and half block ingot meeting dimensional requirements. B899.
1.2 The values stated in inch-pound units are to be regarded 3.2 Definitions of Terms Specific to This Standard:
as standard. The values given in parentheses are mathematical 3.2.1 jumbo ingot, n—large casting of zinc or zinc alloy,
conversions to SI units that are provided for information only having through holes for chains, designed for handling by
and are not considered standard. mechanical equipment, with a nominal weight of 2400 pounds,
which is also referred to as a jumbo or strip jumbo.
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the 3.2.2 block ingot, n—large casting of zinc or zinc alloy,
responsibility of the user of this standard to become familiar having lift pockets, designed for handling by mechanical
with all hazards including those identified in the appropriate equipment, with a nominal weight of 2400 pounds, which is
Material Safety Data Sheet (MSDS) for this product/material also referred to as a block.
as provided by the manufacturer, to establish appropriate
3.2.3 half block ingot, n—large casting of zinc or zinc alloy,
safety and health practices, and determine the applicability of
having lift pockets, designed for handling by mechanical
regulatory limitations prior to use.
equipment, with a nominal weight of 1200 pounds, which is
also referred to as half block.
2. Referenced Documents
4. Ordering Information
2.1 The following standards of the issue in effect on date of
4.1 Orders for jumbo, block, or half block ingots under this
order acceptance, form a part of this specification to the extent
specification shall include the following information in addi-
referenced herein:
tion to the appropriate information specified in Specification
2
2.2 ASTM Standards:
B949, Section 4:
B6 Specification for Zinc
4.1.1 Type of ingot (Jumbo, Type 1 Block, Type 2 Block,
B852 Specification for Continuous Galvanizing Grade
Half Block Type 1, or Half Block Type 2).
(CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet
4.1.2 Order may stipulate dimensions, or tolerances, or
Steel
both, not meeting this specification only upon mutual written
B899 Terminology Relating to Non-ferrous Metals and Al-
agreement between purchaser and producer.
loys
B949 Specification for General Requirements for Zinc and 5. Materials and Manufacture
Zinc Alloy Products
5.1 The producer shall use care to have each lot of zinc
E29 Practice for Using Significant Digits in Test Data to
metal or zinc alloy jumbo, block or half block ingots be of as
Determine Conformance with Specifications
uniform quality as possible.
6. Dimensions, Mass, and Permissible Variations
1
This specification is under the jurisdiction of ASTM Committee B02 on
6.1 Jumbo Ingots:
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
6.1.1 Permissible variations in dimensions and tolerances
B02.04 on Zinc and Cadmium.
for zinc or zinc alloy jumbo ingots shall be within the limits
Current edition approved April 1, 2010. Published April 2010. Originally
specified in Table 1and Fig. 1 unless prior written agreement
approved in 1999. Last previous edition approved in 2009 as B897 - 09. DOI:
10.1520/B0897-10.
exists between purchaser and producer for nonstandard dimen-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
sions and tolerances.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.1.2 Jumbo ingot weight shall be 2400 6100 lbs (1089 6
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 45 kg).
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B897−10
TABLE 1 Zinc Jumbo Ingot Specification TABLE 3 Zinc Half Block Ingot Specification
Weight 2400 ± 100 lbs (1089 ± 45 kg) Weight 1200 ± 50 lbs (545 ± 23 kg)
Table of Dimensions Table of Dimensions
Drawing Drawing
Identification Dimension Definition Dimension, in. Dimension, mm Identification Dimension Definition Dimension, in. Dimensi
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B897–09 Designation: B897 – 10
Standard Specification for
Configuration of Zinc and Zinc Alloy Jumbo Block and Half
1
Block Ingot
This standard is issued under the fixed designation B897; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers zinc and zinc alloy jumbo, block, and half block ingot meeting dimensional requirements.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 The following standards of the issue in effect on date of order acceptance, form a part of this specification to the extent
referenced herein:
2
2.2 ASTM Standards:
B6 Specification for Zinc
B852 Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel
B899 Terminology Relating to Non-ferrous Metals and Alloys
B949 Specification for General Requirements for Zinc and Zinc Alloy Products
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
3. Terminology
3.1 Terms shall be defined in accordance with Terminology B899.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 jumbo ingot, n—large casting of zinc or zinc alloy, having through holes for chains, designed for handling by mechanical
equipment, with a nominal weight of 2400 pounds, which is also referred to as a jumbo or strip jumbo.
3.2.2 block ingot, n—large casting of zinc or zinc alloy, having lift pockets, designed for handling by mechanical equipment,
with a nominal weight of 2400 pounds, which is also referred to as a block.
3.2.3 half block ingot, n—large casting of zinc or zinc alloy, having lift pockets, designed for handling by mechanical
equipment, with a nominal weight of 1200 pounds, which is also referred to as half block.
4. Ordering Information
4.1 Orders for jumbo, block, or half block ingots under this specification shall include the following information:
4.1.1This specification number and date,
4.1.2Quantity (weight),
4.1.3Name of material and grade, and information in addition to the appropriate information specified in Specification B949,
Section 4:
4.1.41 Type of ingot (Jumbo, Type 1 Block, Type 2 Block, Half Block Type 1, or Half Block Type 2),2).
4.1.52 Order may stipulate dimensions, or tolerances, or both, not meeting this specification only upon mutual written
agreement between purchaser and producer.
1
This specification is under the jurisdiction ofASTM Committee B02 on Nonferrous Metals andAlloys and is the direct responsibility of Subcommittee B02.04 on Zinc
and Cadmium.
Current edition approved Oct.April 1, 2009.2010. Published November 2009.April 2010. Originally approved in 1999. Last previous edition approved in 20032009 as
B897 - 039. DOI: 10.1520/B0897-109.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B897 – 10
5. Materials and Manufacture
5.1 The producer shall use care to have each lot of zinc metal or zinc alloy jumbo, block or half block ingots be of as uniform
quality as possible.
6. Dimensions, Mass, and Permissible Variations
6.1 Jumbo Ingots:
6.1.1 Permissible variations in dimensions and tolerances for zinc or zinc alloy jumbo ingots shall be within the limits specified
in Table 1 and Fig. 1 unless prior written agreement exists between purchaser and p
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.