iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F512-06

(Specification)

Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation

Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation

ABSTRACT
This specification covers the dimensional, design, and performance requirements for five types (Types EB-20, EB-35, DB-60, DB-100, and DB-120) of smooth-wall poly(vinyl chloride) (PVC) conduits and fittings for underground communication and electrical power wires and cables. Conduits and fittings shall be evaluated on impact resistance and strength, joint tightness, pipe stiffness, and extrusion quality.
SCOPE
1.1 This specification covers the requirements for smooth-wall poly(vinyl chloride) conduit and fittings for underground communication and electrical power wire and cables.
1.2 The values given in parentheses are for information only.
The following safety hazards caveat pertains only to the test method portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Apr-2006
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
Technical Committee
F17 - Plastic Piping Systems
Drafting Committee
F17.25 - Vinyl Based Pipe
Current Stage
Ref Project

Relations

Replaces
ASTM F512-95(2001)e1 - Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation
Effective Date
01-May-2006
Replaced By
ASTM F512-12 - Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation
Effective Date
01-Aug-2012
Referred By
ASTM D2855-20 - Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
Effective Date
01-May-2006
Referred By
ASTM F1760-16(2020) - Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content
Effective Date
01-May-2006
Referred By
ASTM F1488-14(2019) - Standard Specification for Coextruded Composite Pipe
Effective Date
01-May-2006
Referred By
ASTM F1365-91(2023) - Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals
Effective Date
01-May-2006
Referred By
ASTM D2672-20e1 - Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement
Effective Date
01-May-2006

Buy Standard

ASTM F512-06 - Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground InstallationASTM F512-06 - Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation
PreviousNext
Technical specification
ASTM F512-06 - Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F512 −06 AnAmerican National Standard
Standard Specification for
Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and
1
Fittings for Underground Installation
ThisstandardisissuedunderthefixeddesignationF512;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D2466 Specification for Poly(Vinyl Chloride) (PVC) Plastic
Pipe Fittings, Schedule 40
1.1 This specification covers the requirements for smooth-
D2564 Specification for Solvent Cements for Poly(Vinyl
wall poly(vinyl chloride) conduit and fittings for underground
Chloride) (PVC) Plastic Piping Systems
communication and electrical power wire and cables.
D2855 Practice for Making Solvent-Cemented Joints with
1.2 The values given in parentheses are for information
Poly(Vinyl Chloride) (PVC) Pipe and Fittings
only.
F412 Terminology Relating to Plastic Piping Systems
1.3 The following safety hazards caveat pertains only to the
test method portion, Section 8, of this specification: This
3. Terminology
standard does not purport to address all of the safety concerns,
3.1 Definitions are in accordance with Terminology F412
if any, associated with its use. It is the responsibility of the user
and abbreviations are in accordance with Terminology D1600,
of this standard to establish appropriate safety and health
unless otherwise specified. The abbreviation for poly(vinyl
practices and determine the applicability of regulatory limita-
chloride) is PVC.
tions prior to use.
3.2 Definitions of Terms Specific to This Standard:
2. Referenced Documents
3.2.1 external recycled material—industrial rework gener-
2
ated by a different company manufacturing to this specifica-
2.1 ASTM Standards:
tion. Composition is known by the industrial source of the
D618 Practice for Conditioning Plastics for Testing
material.
D1600 Terminology forAbbreviatedTerms Relating to Plas-
tics
3.2.2 post-consumer recycled material—finished goods that
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
have been purchased by the public, then returned to industry
Compounds and Chlorinated Poly(Vinyl Chloride)
and reprocessed into raw materials. Identity of finished goods
(CPVC) Compounds
is known by the reprocessing company.
D2122 Test Method for Determining Dimensions of Ther-
3.2.3 certificate of composition—a certificate describing the
moplastic Pipe and Fittings
certain properties of an external recycled material of a post
D2152 Test Method for Adequacy of Fusion of Extruded
consumer recycled material.
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
3.2.4 composition disclosure—a document describing the
Acetone Immersion
formulation of an external recycled material.
D2412 Test Method for Determination of External Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
4. Classification
D2444 Test Method for Determination of the Impact Resis-
tance of Thermoplastic Pipe and Fittings by Means of a
4.1 This specification covers five types of underground
Tup (Falling Weight)
conduit. There are two having lesser pipe stiffness values,
designed primarily for concrete encased burial (EB), and three
with greater pipe stiffness values, designed primarily for direct
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
burial (DB). The complete designations follow:
Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl
Based Pipe.
Type EB-20 — Designed to be encased in concrete.
Current edition approved May 1, 2006. Published June 2006. Originally
Type EB-35 — Designed to be encased in concrete.
´1
approved in 1977. Last previous edition approved in 2001 as F512 – 95(2001) .
Type DB-60 — Designed for direct burial without encasement in concrete.
DOI: 10.1520/F0512-06.
Type DB-100 — Designed for direct burial without encasement in concrete.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Type DB-120 — Designed for direct burial without encasement in concrete.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4.2 This specification covers conduit with integral bells, or
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. with either separate or attached couplings.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F512−06
4.3 This specification covers molded and fabricated fittings of the conduit, including integral bell, or coupling if attached,
intended for use with all types of conduit. unless otherwise specified. Tolerance on len
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2945-18(2023)(Specification)
Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings

ABSTRACT
This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas piping. The pipe and fittings covered by this specification are intended for use in the transport of fuel gases. This specification does not cover threaded pipe. The polyamide 11 material used to make pipe and fittings shall be virgin or reworked material and shall have a Plastics Pipe Institute (PPI) long-term hydrostatic design stress and hydrostatic design basis rating as determined per PPI TR3 and PPI TR4. This specification deals with requirements for materials, requirements for pipe and fittings, test methods, marking, and quality Assurance.
SCOPE
1.1 This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas pipelines. The pipe and fittings covered by this specification are intended for use in the distribution and transmission of fuel gases.  
1.1.1 This specification does not cover threaded pipe. Generic fusion guidelines are given in Appendix X1. Design considerations are discussed in Appendix X2. In-plant quality control programs are specified in Annex A1.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
Note 1: Heat fusion joining of PA11 pipe and fittings meeting the requirements of this standard is limited to PA11 pipe and fittings meeting the requirements of this standard. Heat Fusion joining of PA11 pipe and fittings meeting the requirements of this standard is not allowed to pipes and fittings made from any other thermoplastic materials (for example, PA12, PEs, PVCs, etc.).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following is an index of the annexes and appendixes in this specification:    
Annexes  
Subject  
Annex A1  
In-Plant Quality Control for sizes up to 12 in.  
Annex A2  
PA-11 Butt Fusion Fittings  
Appendixes  
Subject  
Appendix X1  
Butt Fusion Guidelines for PA-11 Piping  
Appendix X2  
Design Consideration  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM D2152-23(Test Method)
Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion

SIGNIFICANCE AND USE
3.1 This test method is applicable only for distinguishing between inadequately fused and adequately fused PVC. The difference between thermally degraded and adequately fused PVC cannot be detected by this test method. Acetone immersion testing is not a substitute for burst, impact, or other physical or chemical tests on PVC pipe or fittings and it, therefore, shall not be used as the only test specification for purchasing of PVC pipe and fittings. This test method only detects inadequate fusion and does not determine the over-all quality of the PVC pipe or fittings.  
3.2 This test method is useful in determining whether inadequate fusion contributed to failure of PVC pipe or fittings in other physical or chemical tests, or in service.  
3.3 This test method is useful in evaluating the adequacy of PVC fusion obtained in process or materials trials.  
3.4 This test method determines adequacy of fusion on a single, relatively small specimen. This test method requires the use of a hazardous reagent which must be properly handled and disposed. Therefore, this test method may not be cost-effective to employ as a routine quality control test.
SCOPE
1.1 This test method covers the determination of the adequacy of fusion of extruded rigid poly(vinyl chloride) (PVC) pipe and molded fittings as indicated by reaction to immersion in anhydrous acetone.  
1.2 The values stated in inch-pound units are to be regarded as the standard except where instruments are calibrated in SI units.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific hazards statements are given in Annex A1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3034-23(Specification)
Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

ABSTRACT
This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining systems and a form of marking for type PSM poly(vinyl chloride) (PVC) sewer pipe and fittings. The pipe and fittings shall be homogeneous throughout and free from visible cracks, holes, foreign inclusions, or other injurious defects. The socket diameters, socket depth, wall thickness, pipe flattening, impact resistance, pipe stiffness, joint tightness, and extrusion quality shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining systems and a form of marking for type PSM poly(vinyl chloride) (PVC) sewer pipe and fittings.  
1.2 Pipe and fittings produced to this specification should be installed in accordance with Practice D2321.  
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification:   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM F2817-13(2023)(Specification)
Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair

SCOPE
1.1 This specification covers requirements for PVC pipe and tubing for use only to maintain or repair existing PVC gas piping. This specification covers requirements for fittings for use to maintain or repair existing PVC gas piping.  
1.1.1 In-plant quality control programs are specified in Annex A1.  
1.2 The text of this specification references notes and, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following is an index of the annexes in this specification:    
Annex  
Subject  
Annex A1  
In-Plant Quality Control for PVC materials
up to 6 in.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F2928-18(2023)(Practice)
Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods

SIGNIFICANCE AND USE
5.1 This practice provides requirements for standardized preparation of sample butt fusions, preparation of specimens from sample butt fusions, and conditioning for testing in accordance with Test Method D638, Test Method D1598, or Test Method D1599. This practice is intended to improve the ability to reliably compare test results from multiple parties.
SCOPE
1.1 This practice provides standardized sample butt fusion preparation, conditioning, and testing conditions for tension testing of specimens prepared from sample butt fusion joints or hydrostatic tests of sample butt fusion joints in accordance with:  
1.1.1 Test Method D638, tension testing;
1.1.1.1 The preparation or use of tensile specimens other than Test Method D638 Type I through Type V is beyond the scope of this practice.  
1.1.2 Test Method D1598, constant (sustained) hydraulic pressure testing;  
1.1.3 Test Method D1599, short-term hydraulic pressure testing.  
1.1.4 It is not within the scope of this practice to include plastic materials other than polyethylene or other tests for butt fusions. The exclusion of other plastic materials and other tests does not imply that other plastic materials are suitable or unsuitable for butt fusion, or that the tests cited herein are adequate or inadequate for qualitative characterization and for research and development of butt fusion joints, or that other tests do not have lesser, equal, or greater utility for such purpose.  
1.1.5 The evaluation of test results and the determination of test result evaluation criteria are not within the scope of this practice. This practice is limited to standardized butt fusion test specimens and testing conditions for the comparison of test data from multiple parties.  
1.1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.1.7 In this standard, text in parentheses, notes in the body of the standard and appendices are informational and non-mandatory. For tables in the body of the standard, table notes are mandatory.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM F409-22(Specification)
Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

ABSTRACT
This specification covers the material, dimensional ,and performance requirements and associated test methods for thermoplastic tubes and fittings for accessible and replaceable domestic waste connections. The tubes, fittings and mechanical joint components shall be made of either virgin acrylonitrile-butadiene-styrene (ABS) plastic, virgin poly(vinyl chloride) (PVC) plastic, or virgin polypropylene plastic. When evaluated by the test procedures provided herein, the products shall adhere to requirements stipulated for hydrostatic pressure, axial stress, joint integrity, and solvent cement.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, hydrostatic pressure, joint integrity, and solvent cement for thermoplastic tube and fittings for accessible and replaceable domestic waste connections. Marking requirements are also included. Thermoplastic that does not meet the material requirements specified in Section 5 is excluded.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    16 pages
    English language
    sale 15% off
  • Technical specification
    16 pages
    English language
    sale 15% off
ASTM
ASTM D2122-22(Test Method)
Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

SIGNIFICANCE AND USE
5.1 This test method provides for determining the physical dimensions of thermoplastic pipe and fittings. This test method is suitable for determination of dimensional compliance with product specifications.
SCOPE
1.1 This test method covers the determination of diameter, wall thickness, and length dimensions of thermoplastic pipe. Included are procedures for measurement of the inside diameter of pipe intended to be joined by internal fittings, measurement of the average outside diameter for roundable pipe where out-of-roundness is not of primary concern, out-of-roundness measurement and measurement of the average outside diameter of non-roundable pipe, and for determining length and straightness.  
1.2 This test method also includes procedures for dimensioning molded thermoplastic pipe fittings.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D2729-21(Specification)
Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

ABSTRACT
This specification covers requirements and test methods for materials, dimensions, workmanship, chemical resistance, and joint tightness of poly (vinyl chloride) (PVC) sewer and drain pipe and fittings. The pipe shall be made from virgin cell 12164 with a certain minimum tensile strength, 12454 or 12454 poly(vinyl chloride) compounds. The fittings shall be made from virgin poly(vinyl chloride) compounds of cell classification PVC 12454, PVC 12454, or PVC 13343. Compounds that have different cell classification because one or more properties are superior to those of the specified compounds are also acceptable. In order to determine the overall performance of the pipes and fittings, the following tests shall be done: flattening test, joint tightness test, and perforation test. The pipe and fittings shall be homogeneous throughout and free from visible cracks, holes, foreign inclusions, or other injurious defects. The pipe shall be as uniform as commercially practical in color, opacity, density, and other physical properties.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, chemical resistance, and joint tightness of poly(vinyl chloride) (PVC) sewer and drain pipe and fittings. Perforated pipe is also covered; the joint tightness test is not applicable for perforated pipe. A form of marking to indicate compliance with this specification is also included.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2390-21(Specification)
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content

ABSTRACT
This specification covers the basic requirements and corresponding test methods for poly(vinyl chloride) (PVC) plastic drain, waste, and vent (DWV) pipes and fittings that contain a uniform blend of virgin PVC compound and post-industrial recycle material. When evaluated by the test procedures provided herein, the pipes and fittings shall conform to specified values of the following requirements: dimensions; pipe stiffness, deflection load, lower confidence limit, and flattening resistance; crush resistance; impact resistance; hydrostatic burst resistance; and solvent cement.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, hydrostatic burst resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent (DWV) pipe and fittings.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F2929-17(2021)(Specification)
Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig

ABSTRACT
This specification establishes the requirements for 0.070 in. wall thickness crosslinked polyethylene (PEX) tubing that is outside diameter controlled, and intended for non-potable radiant heating applications for pressures up to 75 psig. It covers requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, bent-tube hydrostatic pressure, environmental stress cracking, stabilizer functionality, excessive temperature and degree of crosslinking, as well as requirements for tubing markings.
SCOPE
1.1 This specification covers 0.070 in. wall thickness crosslinked polyethylene (PEX) tubing that is outside diameter controlled, and intended for non-potable radiant heating applications for pressures up to 75 psig in sizes 5/8 NTS (nominal tubing size) and 7/8 NTS. This specification also includes fittings that are specifically designed for this 0.070 in.-wall PEX tubing. Only maximum 75-psig relief valves shall be used with this tubing. Included in this specification are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, environmental stress cracking, stabilizer functionality, bent-tube hydrostatic pressure, excessive temperature and degree of crosslinking. Requirements for tubing markings are also given. This specification incorporates an optional middle or outer oxygen barrier layer. This tubing is not intended for field bending at temperatures above 120 ºF (49 ºC).  
1.2 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off