iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F486-87(1996)e1

(Practice)

Standard Practice for Preparation of Use and Care Booklets for Vacuum Cleaners

Standard Practice for Preparation of Use and Care Booklets for Vacuum Cleaners

SCOPE
1.1 This practice identifies the information to be provided through the use and care booklet accompanying a particular model of vacuum cleaner.  
1.2 Included is information that the user needs to operate and maintain the vacuum cleaner and the attachments provided in a proper and safe manner.  
1.2.1 Similar information is included for attachments that are sold separately.

General Information

Status
Historical
Publication Date
09-Mar-2001
ICS
97.080 - Cleaning appliances
Technical Committee
F11 - Vacuum Cleaners
Drafting Committee
F11.93 - Consumer Information
Current Stage
Ref Project

Relations

Replaced By
ASTM F486-01 - Standard Practice for Preparation of Use and Care Booklets for Vacuum Cleaners
Effective Date
10-Mar-2001

Buy Standard

ASTM F486-87(1996)e1 - Standard Practice for Preparation of Use and Care Booklets for Vacuum CleanersASTM F486-87(1996)e1 - Standard Practice for Preparation of Use and Care Booklets for Vacuum Cleaners
PreviousNext
Standard
ASTM F486-87(1996)e1 - Standard Practice for Preparation of Use and Care Booklets for Vacuum Cleaners
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
e1
Designation: F 486 – 87 (Reapproved 1996)
Standard Practice for
Preparation of Use and Care Booklets for Vacuum Cleaners
This standard is issued under the fixed designation F 486; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
e NOTE—Section 6.1.19 was corrected editorially in August 1996.
1. Scope differences between the models should be precisely and clearly
shown in the booklet by illustrations and wording.
1.1 This practice identifies the information to be provided
5.2.2 All models included in the booklet should be identi-
through the use and care booklet accompanying a particular
fied by model name or series on the front cover along with a
model of vacuum cleaner.
photograph or drawing of the basic model.
1.2 Included is information that the user needs to operate
5.2.3 The size of the booklet should be no larger than 8 ⁄2 by
and maintain the vacuum cleaner and the attachments provided
11 in. (216 by 279 mm) and no smaller than 5 by 7 in. (127 by
in a proper and safe manner.
178 mm) in size.
1.2.1 Similar information is included for attachments that
5.2.4 The wording in the booklet should be as nontechnical
are sold separately.
as possible.
2. Referenced Documents
5.2.5 Illustrations and wording should be used to identify
vacuum cleaner parts, attachments, and features.
2.1 ASTM Standards:
5.2.6 Instructions for maintenance, storage, assembly, and
F 395 Terminology Relating to Vacuum Cleaners
disassembly of the product by the user should be accompanied
3. Terminology
by illustrations as well as wording.
3.1 Definitions:
6. Content
3.1.1 Refer to Terminology F 395.
6.1 There should be a section on each of the following
4. Significance and Use
subjects in the use and care booklet or on separate sheets that
accompany it. When separate sheets are used they should be
4.1 The user must understand how to operate and maintain
referenced in the use and care booklet:
the equipment to achieve satisfactory cleaning results. Since
6.1.1 Cover, with identification of the product(s) and spe-
the manufacturers are the prime source of this information, it is
cific model(s),
their responsibility to provide instructions for specific models.
6.1.2 Table of contents, if needed for clarity,
Clear, concise, simple (but complete) instructions for the safe
6.1.3 Important safeguards in use and care,
use and maintenance will encourage users to read the informa-
6.1.4 Illustration of vacuum cleaner with major components
tion and follow proper procedures. This will increase user
and attachments identified,
satisfaction, minimize safety problems and decrease com-
6.1.5 Explanation and illustration of user assembly proce-
plaints.
dure and identification of parts to be assembled,
5. General Requirements
6.1.6 List of cleaning attachments provided with the
vacuum cleaner. Instructions on how to connect and disconnect
5.1 Information pertinent to the proper and safe manner of
attachments. Information and suggestions on the u
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F888-06(2024)(Test Method)
Standard Test Method for Measuring Maximum Function Volume of the Primary Dirt Receptacle in a Vacuum Cleaner

SIGNIFICANCE AND USE
3.1 This test method covers a procedure to determine the maximum functional volume of the primary dirt receptacle when installed in the vacuum cleaner.  
3.2 This test method provides the maximum amount of test media that the primary dirt receptacle will hold and may be more than the volume obtained when filled to the manufacturer's recommended fill line.
SCOPE
1.1 This test method covers household types of upright, canister, and combination vacuum cleaners.  
1.2 This test method provides a measurement in dry quarts or litres of the maximum functional volume of the primary dirt receptacle when installed in the vacuum cleaner.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 7.2 and 8.5.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F2756-24(Test Method)
Standard Test Method for Determining Energy Consumption of Vacuum Cleaners

SIGNIFICANCE AND USE
4.1 This test method provides an indication of the amount of energy usage of the vacuum cleaner while operating over a specified cleaning area at a specified stroke speed and total number of cleaning strokes.  
4.1.1 The test area is divided into a number of strips, the strip being defined as the width of the power head or nozzle. For the purpose of this procedure, the cleaning area is specified as 10 m2  (15 500 in.2), the stroke speed is defined as 0.5 m/s ± 0.03 m/s (1.7 ft/s ± 0.1 ft/s), with a total of 10 strokes per strip.  
4.2 In order to provide a uniform basis for measuring the performance described in 1.1, standardized test carpets are employed in this procedure.
SCOPE
1.1 This test method covers only a laboratory test for determining the energy usage-of household and commercial upright, canister, stick, and wet/dry vacuum cleaners operating on carpet when tested under specified conditions.  
1.1.1 This procedure may be used in conjunction with other performance criteria, such as cleaning effectiveness.  
1.1.2 Vacuum cleaners, other than upright vacuum cleaners, that provide a carpet-cleaning function are tested in accordance with the carpet-cleaning instructions provided in the manufacturer’s instruction manual. If the manufacturer’s instruction manual does not contain instructions for a carpet-cleaning function, the vacuum cleaner is not within the scope of this procedure.  
1.2 This test method is applicable to household and commercial types of vacuum cleaners.  
1.3 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are mathematical conversions that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F608-24(Test Method)
Standard Test Method for Evaluation of Carpet Embedded Dirt Removal Effectiveness of Household/Commercial Vacuum Cleaners

SIGNIFICANCE AND USE
4.1 This test method provides an indication of the capability of the vacuum cleaner to remove embedded dirt from carpeting. This test method is based upon results of home cleaning tests so that, in most cases, a reasonable correlation exists between home and laboratory results. The amount of dirt picked up in the laboratory test may not be the same as in the home; however, it will show that, in most cases, a vacuum cleaner that performs well in the laboratory will perform well in a home. Laboratory results may differ due to variations in the homes, carpets, dirt, and other factors (see Section 6).  
4.2 In order to provide a uniform basis for measuring the performance described in 1.1, standardized test carpets and a standardized test dirt are employed in this procedure.
SCOPE
1.1 This test method covers only a laboratory test for determining the relative carpet dirt removal effectiveness of household/commercial vacuum cleaners when tested under specified conditions.  
1.2 This test method is applicable to household/commercial types of upright, canister, and combination cleaners.  
1.3 The test method applies to embedded dirt removal from carpets, not the removal of surface litter and debris.
Note 1: The F11.21 subcommittee is actively pursuing new market relevant carpets with the assistance of the carpet industry. Although plush and Frieze carpet panels are no longer available for purchase, some laboratories may still have samples for testing. In such cases, the table values remain valid.
Note 2: Due to the influence of environmental conditions, variations in time, origin of test materials, and proficiency of the operator, most of the described test methods will give more reliable results when applied for comparative testing of a number of appliances at the same time, in the same laboratory, and by the same operator until a new interlaboratory study has been completed to provide repeatability and reproducibility values.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    24 pages
    English language
    sale 15% off
  • Standard
    24 pages
    English language
    sale 15% off
ASTM
ASTM F1334-24(Test Method)
Standard Test Method for Determining A-Weighted Sound Power Level of Vacuum Cleaners

SIGNIFICANCE AND USE
4.1 The test results enable the comparison of A-weighted sound emission from vacuum cleaners, backpack vacuum cleaners, extractors, or hard-floor cleaning machines when tested under the condition of this test method.
SCOPE
1.1 This test method calculates the overall A-weighted sound power level emitted by small portable upright, canister, combination vacuum cleaners, backpack vacuum cleaners, hard-floor cleaning machines, extractors, and central vacuum cleaner motorized nozzles intended for operation in domestic and commercial applications.  
1.1.1 To determine the Sound Power Level of a central vacuum at the power unit location refer to Test Method F2544.  
1.2 A-weighted sound pressure measurements are performed on a stationary vacuum cleaner, extractor, hard-floor cleaning machine, or backpack vacuum cleaner in a semi-reverberant room. This test method determines sound power by a comparison method for small noise sources, that is, comparison to a broadband reference sound source.  
1.3 This test method describes a procedure for determining the approximate A-weighted sound power level of small noise sources. This test method uses a non-special semi-reverberant room.  
1.4 Results are expressed as A-weighted sound power level in decibels (referenced to one picowatt).  
1.5 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.
Note 1: The F11.21 subcommittee is actively pursuing new market relevant carpets with the assistance of the carpet industry. Although plush and Freize carpet panels are no longer available for purchase, some laboratories may still have samples for testing. In such cases, the table values remain valid.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM F3150-18(2024)(Specification)
Standard Specification for HEPA Filtration System Performance of Residential and Commercial Vacuum Cleaners

ABSTRACT
This specification defines the minimum filtration efficiency requirements for achieving HEPA performance for filtration systems of residential and commercial vacuum cleaners. Only residential and commercial vacuum cleaning products that are used in non-critical applications (applications not requiring the removal of hazardous dust as defined per IEC 60335-2-69) are covered by this specification.
SCOPE
1.1 This specification defines industry acceptable test methods and approaches for evaluating residential and commercial vacuum cleaner filtration systems to HEPA filtration performance levels.  
1.2 This specification defines the minimum filtration efficiency requirements for achieving HEPA performance for filtration systems of residential and commercial vacuum cleaners.  
1.3 This specification applies only to residential and commercial vacuum cleaning products that are used in non-critical applications. Non-critical applications refers to applications not requiring the removal of hazardous dust as defined per IEC 60335-2-69.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F555-01(2023)(Test Method)
Standard Test Method for Motor Life Evaluation of an Upright Vacuum Cleaner

SIGNIFICANCE AND USE
4.1 The test results provide an indication of the motor life of an electric upright vacuum cleaner. End of motor life will be judged in accordance with Section 3.
SCOPE
1.1 This test method covers motor life evaluation of household or commercial single and dual motor upright vacuum cleaners (uprights with separate motors for creating the vacuum and driving the floor brush). Self-propelled or power-assist cleaners are not within the scope of this test method.  
1.2 This test method is limited to evaluation of the upright vacuum cleaner electric motor(s).  
1.3 This test method provides a test to determine operating life of the motor(s), before servicing is needed, by an accelerated laboratory procedure. Motor(s) are tested while mounted and operated in the upright vacuum cleaner.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F884-01(2023)(Test Method)
Standard Test Method for Motor Life Evaluation of a Built-In (Central Vacuum) Vacuum Cleaner

SIGNIFICANCE AND USE
4.1 The test results provide an indication of the motor life of an electric vacuum cleaner. The end of the motor life will be judged in accordance with Section 3.
SCOPE
1.1 This test method is limited to motor life evaluation of central vacuum cleaners.  
1.2 This test method provides a test to determine operating life of the motor, before servicing is needed, by an accelerated laboratory procedure. The motor is tested while mounted and is operated in central vacuum cleaner.  
1.3 The values as stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1692-01(2023)(Test Method)
Standard Test Method for Life Evaluation of a Turbine-Powered Nozzle for Household Central Vacuum Cleaning Systems

SIGNIFICANCE AND USE
4.1 The test results provide an indication of the turbine-powered nozzle life. The end of turbine life will be judged in accordance with 3.1.1.
SCOPE
1.1 This test method covers the turbine-powered nozzle used in household central vacuum cleaning systems.  
1.2 This test method provides a test for determining the operating turbine life in hours by an accelerated laboratory procedure. The turbine is tested while mounted and operated in the power nozzle.  
1.3 This test method covers only the turbine-powered nozzle. The system used to provide the airflow source is not under consideration.  
1.4 This test method is limited to the determination of turbine life for a household turbine-powered nozzle.  
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F922-01(2023)(Test Method)
Standard Test Method for Motor Life Evaluation of an Electric Motorized Nozzle

SIGNIFICANCE AND USE
4.1 The test results provide an indication of the motor life of an electric motorized nozzle. End of motor life will be judged in accordance with Section 3.
SCOPE
1.1 This test method covers the motorized nozzle used with household or commercial vacuum cleaner systems, that is, combination cleaners.  
1.2 This test method provides a test for determining operating motor life in hours by an accelerated laboratory procedure. The motors are tested while mounted and operated in the motorized nozzle.  
1.3 This test method covers only the motorized nozzle. The system used to provide the airflow source is not under consideration.  
1.4 This test method is limited to the determination of motor life for an electrically powered household or commercial motorized nozzle.  
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM F1409-23(Test Method)
Standard Test Method for Straight Line Movement of Vacuum Cleaners While Cleaning Carpets

SIGNIFICANCE AND USE
4.1 This test method measures the horizontal component of the relative work required by the user during the cleaning operation for the movement of a vacuum cleaner in the home or other cleaning location on standardized laboratory carpeting. Work is determined from the forces measured in the horizontal direction only by the mobility equipment.  
4.2 This measurement is relative to the work performed by the user of vacuum cleaners and may be used for comparison between vacuum cleaners.  
4.3 The relation between actual vacuum cleaner usage and the method of operation is valid only if the vacuum cleaner user operates the vacuum cleaner properly and in accordance with the manufacturer's instructions.
SCOPE
1.1 This test method covers a measurement of the relative work required to move an upright, canister, stick, or combination vacuum cleaner in a straight line with forward and backward stroking on a selection of typical carpeted surfaces.  
1.1.1 This test method measures only the horizontal component of work required to move the vacuum cleaner on carpet.  
1.2 This test method can be used in the testing of household and commercial vacuum cleaners.  
1.3 This test method measures the relative work needed to move the vacuum cleaner with its motor or motors in operation.  
1.4 This test method applies to the vacuum cleaning of carpets only.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: The F11.21 subcommittee is actively pursuing new market relevant carpets with the assistance of the carpet industry. Section 12 has been revised to remove carpets that are no longer available (that is, plush, Frieze).  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off