ASTM D2683-10e3

Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing

ABSTRACT
This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe and tubing. Fittings covered by this specification are normally molded. In-line fittings such as couplings, unions, bushings, caps, nipples, etc., may be extruded or machined from extruded stock. Special fittings such as transition fittings and tapping teets shall be assembled and fabricated. Conditioning, dimensions, short-term rupture test, and sustained pressure test shall be performed to conform with the requirements specified.
SCOPE
1.1 This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe as specified by Specifications D3035 and D2513. Requirements for materials, workmanship, dimensions, and pressure performance are included. Where applicable in this specification, “ pipe” shall mean “pipe and tubing.”  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 28-Feb-2010
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.10 - Fittings

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´3
Designation:D2683 −10 AnAmerican National Standard
Standard Specification for
Socket-Type Polyethylene Fittings for Outside Diameter-
1
Controlled Polyethylene Pipe and Tubing
This standard is issued under the fixed designation D2683; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—6.2.2 was editorially corrected in March 2013.
2
ε NOTE—8.5.2 was editorially corrected in March 2014.
3
ε NOTE—6.2.2 was editorially corrected in May 2014.
1. Scope* D2122 Test Method for Determining Dimensions of Ther-
moplastic Pipe and Fittings
1.1 This specification covers polyethylene socket-type fit-
D2513 Specification for Polyethylene (PE) Gas Pressure
tings for use with outside diameter-controlled polyethylene
Pipe, Tubing, and Fittings
pipeasspecifiedbySpecificationsD3035andD2513.Require-
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe
ments for materials, workmanship, dimensions, and pressure
and Fittings
performance are included. Where applicable in this
D3035 SpecificationforPolyethylene(PE)PlasticPipe(DR-
specification, “ pipe” shall mean “pipe and tubing.”
PR) Based on Controlled Outside Diameter
1.2 The values stated in inch-pound units are to be regarded
D3350 Specification for Polyethylene Plastics Pipe and Fit-
as standard. The values given in parentheses are mathematical
tings Materials
conversions to SI units that are provided for information only
F412 Terminology Relating to Plastic Piping Systems
and are not considered standard.
2.2 Federal Standard:
3
1.3 The following safety hazards caveat pertains only to the
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
test method portion, Section 8, of this specification: This
2.3 Military Standard:
3
standarddoesnotpurporttoaddressallofthesafetyconcerns,
MIL-STD-129 Marking for Shipment and Storage
ifany,associatedwithitsuse.Itistheresponsibilityoftheuser 4
2.4 Plastic Pipe Institute
of this standard to establish appropriate safety and health
PPI TR-3 Policies and Procedures for Developing Hydro-
practices and determine the applicability of regulatory limita-
static Design Basis (HDB), Pressure Design Basis (PDB),
tions prior to use.
Strength Design Basis (SDB), and Minimum Required
Strength (MRS) Ratings for Thermoplastic Piping Mate-
2. Referenced Documents
rials or Pipe7
2
2.1 ASTM Standards:
PPI TR-4 HDB/SDB/PDB/MRS Listed Materials, PPI List-
D618 Practice for Conditioning Plastics for Testing
ing of Hydrostatic Design Basis (HDB), Strength Design
D1598 Test Method for Time-to-Failure of Plastic Pipe
Basis(SDB),PressureDesignBasis(PDB),andMinimum
Under Constant Internal Pressure
Required Strength (MRS) Ratings for Thermoplastic Pip-
D1599 Test Method for Resistance to Short-Time Hydraulic
ing Materials or Pipe
Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology forAbbreviatedTerms Relating to Plas- 3. Terminology
tics
3.1 Definitions are in accordance with Terminology F412
and abbreviations are in accordance with Terminology D1600,
unless otherwise specified. The abbreviation of polyethylene
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
plastic is PE.
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved March 1, 2010. Published April 2010. Originally
approved in 1968. Last previous edition approved in 2004 as D2683 – 04. DOI:
3
10.1520/D2683-10E03. Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM dodssp.daps.dla.mil.
4
Standards volume information, refer to the standard’s Document Summary page on Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825,
the ASTM website. Irving, TX 75062, http://www.plasticpipe.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´3
D2683−10
3.2 standard thermoplastic pipe dimension ratio (SDR)— 6. Requirements
the ratio of pipe outside diameter to wall thickness. It is
6.1 Dimensions and Tolerances:
calculated by dividing the average outside diameter of the pipe
6.1.1 Fittings, sockets, dimensions, and tolerances shall be
by the minimum wall thickness.
as shown in Table 2, Tab
...