ASTM A804/A804M-04(2009)e1
(Test Method)Standard Test Methods for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Sheet-Type Test Specimens
Standard Test Methods for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Sheet-Type Test Specimens
SIGNIFICANCE AND USE
Materials Evaluation—These test methods were developed to supplement the testing of Epstein specimens for applications involving the use of flat, sheared laminations where the testing of Epstein specimens in either the as-sheared or stress-relief-annealed condition fails to provide the most satisfactory method of predicting magnetic performance in the application. As a principal example, the test methods have been found particularly applicable to the control and evaluation of the magnetic properties of thermally flattened, grain-oriented electrical steel (Condition F5, Specification A876) used as lamination stock for cores of power transformers. Inasmuch as the test methods can only be reliably used to determine unidirectional magnetic properties, the test methods have limited applicability to the testing of fully processed nonoriented electrical steels as normally practiced (Specification A677).
Specification Acceptance—The reproducibility of test results and the accuracy relative to the 25-cm [250-mm] Epstein method of test are considered such as to render the test methods suitable for materials specification testing.
Interpretation of Test Results—Because of specimen size, considerable variation in magnetic properties may be present within a single specimen or between specimens that may be combined for testing purposes. Also, variations may exist in test values that are combined to represent a test lot of material. Test results reported will therefore, in general, represent averages of magnetic quality and in certain applications, particularly those involving narrow widths of laminations, deviations in magnetic performance from those expected from reported data may occur at times. Additionally, application of test data to the design or evaluation of a particular magnetic device must recognize the influence of magnetic circuitry upon performance and the possible deterioration in magnetic properties arising from construction of the device.
Recommended Standar...
SCOPE
1.1 These test methods cover the determination of specific core loss and peak permeability of single layers of sheet-type specimens tested with normal excitation at a frequency of 50 or 60 Hz.
Note 1—These test methods have been applied only at the commercial power frequencies, 50 and 60 Hz, but with proper instrumentation and application of the principles of testing and calibration embodied in the test methods, they are believed to be adaptable to testing at frequencies ranging from 25 to 400 Hz.
1.2 These test methods use calibration procedures that provide correlation with the 25-cm [250-mm] Epstein test.
1.3 The range of test magnetic flux densities is governed by the properties of the test specimen and by the available instruments and other equipment components. Normally, nonoriented electrical steels can be tested over a range from 8 to 16 kG [0.8 to 1.6 T] for core loss. For oriented electrical steels, the normal range extends to 18 kG [1.8 T]. Maximum magnetic flux densities in peak permeability testing are limited principally by heating of the magnetizing winding and tests are limited normally to a maximum ac magnetic field strength of about 150 Oe [12 000 A/m].
1.4 These test methods cover two alternative procedures as follows:
Test Method 1—Sections 6-12
Test Method 2—Sections 13-19
1.4.1 Test Method 1 uses a test fixture having (1) two windings that encircle the test specimen, and (2) a ferromagnetic yoke structure that serves as the flux return path and has low core loss and low magnetic reluctance.
1.4.2 Test Method 2 uses a test fixture having (1) two windings that encircle the test specimen, (2) a third winding located inside the other two windings and immediately adjacent to one surface of the test specimen, and (3) a ferromagnetic yoke structure which serves as the flux-return path and has low magnetic reluctance.
1.5 The values and equations stated in customary (cgs-emu and inch-pou...
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: A804/A804M − 04(Reapproved 2009)
Standard Test Methods for
Alternating-Current Magnetic Properties of Materials at
Power Frequencies Using Sheet-Type Test Specimens
This standard is issued under the fixed designationA804/A804M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
ε NOTE—Editorial changes were made throughout in May 2009.
1. Scope cent to one surface of the test specimen, and (3) a ferromag-
netic yoke structure which serves as the flux-return path and
1.1 These test methods cover the determination of specific
has low magnetic reluctance.
core loss and peak permeability of single layers of sheet-type
specimenstestedwithnormalexcitationatafrequencyof50or
1.5 The values and equations stated in customary (cgs-emu
60 Hz.
and inch-pound) units or SI units are to be regarded separately
as standard. Within this standard, SI units are shown in
NOTE 1—These test methods have been applied only at the commercial
brackets except for the sections concerning calculations where
power frequencies, 50 and 60 Hz, but with proper instrumentation and
applicationoftheprinciplesoftestingandcalibrationembodiedinthetest
there are separate sections for the respective unit systems. The
methods, they are believed to be adaptable to testing at frequencies
values stated in each system may not be exact equivalents;
ranging from 25 to 400 Hz.
therefore,eachsystemshallbeusedindependentlyoftheother.
1.2 These test methods use calibration procedures that
Combiningvaluesfromthetwosystemsmayresultinnoncon-
provide correlation with the 25-cm [250-mm] Epstein test.
formance with this standard.
1.3 The range of test magnetic flux densities is governed by
1.6 This standard does not purport to address all of the
the properties of the test specimen and by the available
safety concerns, if any, associated with its use. It is the
instruments and other equipment components. Normally, non-
responsibility of the user of this standard to establish appro-
orientedelectricalsteelscanbetestedoverarangefrom8to16
priate safety and health practices and determine the applica-
kG[0.8to1.6T]forcoreloss.Fororientedelectricalsteels,the
bility of regulatory limitations prior to use.
normal range extends to 18 kG [1.8 T]. Maximum magnetic
flux densities in peak permeability testing are limited princi-
2. Referenced Documents
pally by heating of the magnetizing winding and tests are
2.1 ASTM Standards:
limited normally to a maximum ac magnetic field strength of
A34/A34MPractice for Sampling and Procurement Testing
about 150 Oe [12000 A/m].
of Magnetic Materials
1.4 These test methods cover two alternative procedures as
A340Terminology of Symbols and Definitions Relating to
follows:
Magnetic Testing
Test Method 1—Sections6–12
A343/A343MTest Method for Alternating-Current Mag-
Test Method 2—Sections13–19
netic Properties of Materials at Power Frequencies Using
1.4.1 Test Method 1 uses a test fixture having (1) two
Wattmeter-Ammeter-Voltmeter Method and 25-cm Ep-
windings that encircle the test specimen, and (2) a ferromag-
stein Test Frame
netic yoke structure that serves as the flux return path and has
A677Specification for Nonoriented Electrical Steel Fully
low core loss and low magnetic reluctance.
Processed Types
1.4.2 Test Method 2 uses a test fixture having (1) two
A683Specification for Nonoriented Electrical Steel, Semi-
windings that encircle the test specimen, (2) a third winding
processed Types
located inside the other two windings and immediately adja-
A876Specification for Flat-Rolled, Grain-Oriented, Silicon-
Iron, Electrical Steel, Fully Processed Types
These test methods are under the jurisdiction of ASTM Committee A06 on
Magnetic Properties and are the direct responsibility of Subcommittee A06.01 on
Test Methods. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved May 1, 2009. Published January 2010. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1982. Last previous edition approved in 2004 as A804/A804M–04. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A0804_A0804M-04R09E01. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
´1
A804/A804M − 04 (2009)
3. Terminology material. Test results reported will therefore, in general, repre-
sent averages of magnetic quality and in certain applications,
3.1 Definitions:
particularly those involving narrow widths of laminations,
3.1.1 General—The definitions of terms, symbols, and con-
deviations in magnetic performance from those expected from
version factors relating to magnetic testing found in Terminol-
reported data may occur at times. Additionally, application of
ogy A340 are used in these test methods.
test data to the design or evaluation of a particular magnetic
3.2 Definitions of Terms Specific to This Standard:
devicemustrecognizetheinfluenceofmagneticcircuitryupon
3.2.1 sheet specimen—a rectangular specimen comprised of
performance and the possible deterioration in magnetic prop-
a single piece of material or paralleled multiple strips of
erties arising from construction of the device.
material arranged in a single layer.
4.4 Recommended Standard Tests—Thesetestmethodshave
been principally applied to the magnetic testing of thermally
4. Significance and Use
flattened, grain-oriented electrical steels at 50 and 60 Hz.
4.1 Materials Evaluation—These test methods were devel-
Specific core loss at 15 or 17 kG [1.5 or 1.7 T] and peak
oped to supplement the testing of Epstein specimens for
permeability (if required) at 10 Oe [796 A/m] are the recom-
applications involving the use of flat, sheared laminations
mended parameters for evaluating this class of material.
where the testing of Epstein specimens in either the as-sheared
5. Sampling
or stress-relief-annealed condition fails to provide the most
satisfactory method of predicting magnetic performance in the
5.1 LotSizeandSampling—Unlessotherwiseestablishedby
application.Asaprincipalexample,thetestmethodshavebeen
mutualagreementbetweenthemanufacturerandthepurchaser,
found particularly applicable to the control and evaluation of
determination of a lot size and the sampling of a lot to obtain
the magnetic properties of thermally flattened, grain-oriented
sheets for specimen preparation shall follow the recommenda-
electrical steel (Condition F5, Specification A876) used as
tions of Practice A34/A34M, Sections 5 and 6.
lamination stock for cores of power transformers. Inasmuch as
METHOD 1 TWO-WINDING YOKE-FIXTURE TEST
the test methods can only be reliably used to determine
METHOD
unidirectional magnetic properties, the test methods have
limited applicability to the testing of fully processed nonori-
6. Basic Test Circuit
ented electrical steels as normally practiced (Specification
6.1 Fig. 1 provides a schematic circuit diagram for the test
A677).
method.Apower source of precisely controllable ac sinusoidal
4.2 Specification Acceptance—The reproducibility of test
voltage is used to energize the primary circuit. To minimize
results and the accuracy relative to the 25-cm [250-mm]
flux-waveform distortion, current ratings of the power source
Epsteinmethodoftestareconsideredsuchastorenderthetest
and of the wiring and switches in the primary circuit shall be
methods suitable for materials specification testing.
such as to provide very low impedance relative to the imped-
4.3 Interpretation of Test Results—Because of specimen ance arising from the test fixture and test specimen. Ratings of
size, considerable variation in magnetic properties may be switches and wiring in the secondary circuit also shall be such
present within a single specimen or between specimens that
astocausenegligiblevoltagedropbetweentheterminalsofthe
may be combined for testing purposes. Also, variations may secondary test winding and the terminals of the measuring
exist in test values that are combined to represent a test lot of instruments.
FIG. 1 Basic Circuit Diagram for Method 1
´1
A804/A804M − 04 (2009)
7. Apparatus
7.1 The test circuit shall incorporate as many of the follow-
ing components as are required to perform the desired mea-
surements.
7.2 Yoke Test Fixture—Fig. 2 and Fig. 3 show line drawings
ofasingle-yokefixtureandadouble-yokefixture,respectively.
A double-yoke fixture is preferred in this method but a
single-yoke fixture is permitted. Directions concerning the
design, construction, and calibration of the fixture are given in
7.2.1, 7.2.2, Annex A1, and Annex A2.
7.2.1 Yoke Structure—Various dimensions and fabrication
procedures in construction are permissible. Since the recom-
mended calibration procedure provides correlation with the
25-cm [250-mm] Epstein test, the minimum inside dimension
between pole faces must be at least 22 cm [220 mm]. The
FIG. 3 Double-Yoke Fixture (Exploded View)
thickness of the pole faces should be not less than 2.5 cm [25
mm]. It is recognized that pole faces as narrow as 1.9 cm [19
mm] are being used with nickel-iron yoke systems with good
frequency used. The primary and secondary turns shall be
results. To minimize the influences of coil-end and pole-face wound in the same direction from a common starting point at
effects, the yokes should be longer than the recommended
one end of the coil form.Also, to minimize self-impedances of
minimum. For calibration purposes, it is suggested that the thewindings,theopeninginthecoilformshouldbenogreater
width of the fixture be such as to accommodate a specimen of
than required to allow easy insertion of the test specimen.
at least 36-cm [360-mm] width which corresponds to the Construction and mounting of the test coil assembly must be
combined width of twelve Epstein-type specimens. Should the such that the test specimen will be maintained without me-
fixturewidthbelessthan36cm[360mm],itwillbenecessary chanical distortion in the plane established by the pole faces of
to test each calibration specimen in two parts and average the the yoke(s) of the test fixture.
results.
7.3 Air-Flux Compensator—To provide a means of deter-
7.2.2 Test Windings—The test windings, which shall consist
mining intrinsic induction in the test specimen, an air-core
of a primary (exciting) winding and a secondary (potential)
mutual inductor shall constitute part of the test-coil system.
winding, shall be uniformly and closely wound on a
The respective primary and secondary windings of the air-core
nonmagnetic, nonconducting coil form and each shall span the
inductorandthetest-specimencoilshallbeconnectedinseries
greatestpracticabledistancebetweenthepolefacesoftheyoke
andthevoltagepolaritiesofthesecondarywindingsshallbein
fixture. It is recommended that the number of turns in the
opposition. By proper adjustment of the mutual inductance of
primaryandsecondarywindingsbeequal.Thenumberofturns
the air-core inductor, the average of the voltage developed
may be chosen to suit the instrumentation, mass of specimen
across the combined secondary windings is proportional to the
and test frequency. The secondary winding shall be the
intrinsic induction in the test specimen. Directions for con-
innermost winding and, with instrumentation of suitably high
struction and adjustment of the air-core mutual inductor for
input resistance, normally may consist of a single layer. To
air-flux compensation are found in Annex A3.
reduce self-impedance and thereby minimize flux-waveform
7.4 Flux Voltmeter, V—Afull-wave,true-averagevoltmeter,
f
distortion, it is recommended that the primary winding consist
with scale reading in average voltage times 1.111 so that its
of multiple layers of equal turns connected in parallel. The
indications will be identical with those of a true rms voltmeter
number of such layers should be optimized based on consid-
on a pure sinusoidal voltage, shall be provided for evaluating
eration of a reduction in winding resistance versus an increase
thepeakvalueofthetestmagneticfluxdensity.Toproducethe
ininductivereactanceatthethirdharmonicoftheprincipaltest
estimated precision of test under this method, the full-scale
metererrorsshallnotexceed0.25%(Note2).Metersof0.5%
or more error may be used at reduced accuracy. Either digital
or analog flux voltmeters are permitted. The normally high
input impedance of digital voltmeters is desirable to minimize
loading effects and to reduce the magnitude of instrument loss
compensations. The input resistance of an analog flux voltme-
ter shall not be less than 1000 Ω/V of full-scale indication. A
resistive voltage divider, a standard-ratio transformer, or other
variablescalingdevicemaybeusedtocausethefluxvoltmeter
to indicate directly in units of magnetic flux density if the
combination of basic instrument and scaling device conforms
to the specifications stated above.
FIG. 2 Single-Yoke Fixture (Exploded View) NOTE 2—Inaccuracies in setting the test voltage produce percentage
´1
A804/A804M − 04 (2009)
errors approximately two times as large in the specific core loss. Care
maximum rms primary current to be encountered during
should also be taken to avoid errors caused by temperature and frequency
core-loss testing. Preferably the current-carrying capacity
effects in the instrument.
should be at least 10 rms amperes.
7.4.1 If used with a mutual inductor as a peak ammeter at
7.6.2 Electronic Digital Wattmeter—Electronic digital watt-
magnetic flux densities well above the knee of the magnetiza-
meters have been developed that have proven satisfactory for
tion curve, the flux voltmeter must be capable of accurately
use under the provisions of this test method. Usage of a
measuringtheextremelynonsinusoidal(peaked)voltagethatis
suitable electronic digital wattmeter is permitted as an alterna-
induced in the secondary winding of the mutual inductor.
tive to an electrodynamometer wattmeter in this test method.
Additionally, if so used, an analog flux voltmeter should have
An electronic digital wattmeter oftentimes is preferred in this
an input resistance of 5000 to 10000 Ω/V of full-scale
test method because of its digital readout and its capability for
indication.
direct interfacing with electronic data acquisition systems.
7.6.2.1 The voltage input circuitry of the electronic digital
7.5 RMS Voltmeter, V —A true rms-indicating voltmeter
rms
wattmeter must have an input impedance sufficiently high that
shall be pr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.