ASTM B711-12

Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel Reinforced (AACSR) (6201)

ABSTRACT
This specification covers concentric-lay-stranded conductors made from round-alloy 6201-T81 hard:solution heat treated, cold worked, and then artificially aged wire and round zinc-coated, Zn-5Al-MM coated, aluminum-coated, or aluminum-clad steel core wire for use as overhead electric conductors. Cold-pressure welds, electric-butt welds, and electric-butt, cold-upset welds in the finished individual aluminum alloy wires composing the conductor may be made during the stranding process. The direction of lay of the outside layer of aluminum-alloy wires shall be right-hand. The direction of lay of the aluminum alloy and steel wires shall be reversed in successive layers. The rated strength of a conductor shall be taken as the sum of the strengths of the aluminum alloy and steel components. The mass and electrical resistance of a unit length of stranded conductor shall be calculated. The ares of cross section may be determined by calculations from diameter measurements of the component aluminum wires at any point when measured perpendicularly to their axes.
SCOPE
1.1 This specification covers concentric-lay-stranded conductors made from round aluminum-alloy 6201-T81 hard: solution heat treated, cold worked, and then artificially aged wire and round zinc-coated, Zn-5Al-MM coated, aluminum-coated, or aluminum-clad steel core wire for use as overhead electric conductors (Explanatory Note 1 and Note 2). Note 1—The alloy and temper designations conform to ANSI H35.1. Aluminum alloy 6201 corresponds to Unified Numbering System alloy A96201 in accordance with Practice E527.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 14-Oct-2012
• ICS: 29.240.20 - Power transmission and distribution lines
• Technical Committee: B01 - Electrical Conductors
• Drafting Committee: B01.07 - Conductors of Light Metals

Relations

• Replaces: ASTM B711-05 - Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel Reinforced (AACSR) (6201)
• Effective Date: 15-Oct-2012
• Replaced By: ASTM B711-13 - Standard Specification for Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel Reinforced (AACSR) (6201)
• Effective Date: 01-Jan-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B711 −12
StandardSpecification for
Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel
1
Reinforced (AACSR) (6201)
This standard is issued under the fixed designation B711; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope B398/B398M Specification for Aluminum-Alloy 6201-T81
Wire for Electrical Purposes
1.1 This specification covers concentric-lay-stranded con-
B498/B498M Specification for Zinc-Coated (Galvanized)
ductors made from round aluminum-alloy 6201-T81 hard:
Steel Core Wire for Use in Overhead Electrical Conduc-
solution heat treated, cold worked, and then artificially aged
tors
wire and round zinc-coated, Zn-5Al-MM coated, aluminum-
B500/B500M Specification for Metallic Coated or Alumi-
coated, or aluminum-clad steel core wire for use as overhead
num Clad Stranded Steel Core for Use in Overhead
electric conductors (Explanatory Note 1 and Note 2).
Electrical Conductors
NOTE 1—The alloy and temper designations conform to ANSI H35.1.
B502 Specification for Aluminum-Clad Steel Core Wire for
Aluminum alloy 6201 corresponds to Unified Numbering System alloy
Use in Overhead Electrical Aluminum Conductors
A96201 in accordance with Practice E527.
B606 Specification for High-Strength Zinc-Coated (Galva-
1.2 The values stated in SI units are to be regarded as
nized) Steel Core Wire for Aluminum and Aluminum-
standard. No other units of measurement are included in this
Alloy Conductors, Steel Reinforced
standard.
B802/B802M Specification for Zinc–5 % Aluminum-
1.3 This standard does not purport to address all of the Mischmetal Alloy-Coated Steel Core Wire for Aluminum
Conductors, Steel Reinforced (ACSR)
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- B803 Specification for High-Strength Zinc–5 %Aluminum-
Mischmetal Alloy-Coated Steel Core Wire for Use in
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. Overhead Electrical Conductors
B957 Specification for Extra-High-Strength and Ultra-High-
2. Referenced Documents
Strength Zinc-Coated (Galvanized) Steel Core Wire for
2.1 The following documents of the issue in effect on date
Overhead Electrical Conductors
of material purchase form a part of this specification to the B958 Specification for Extra-High-Strength and Ultra-High-
extent referenced herein.
Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-
2
Coated Steel Core Wire for Use in Overhead Electrical
2.2 ASTM Standards:
Conductors
B263 Test Method for Determination of Cross-Sectional
E29 Practice for Using Significant Digits in Test Data to
Area of Stranded Conductors
Determine Conformance with Specifications
B341/B341M Specification for Aluminum-Coated (Alumi-
E527 Practice for Numbering Metals and Alloys in the
nized) Steel Core Wire for Aluminum Conductors, Steel
3
Unified Numbering System (UNS)
Reinforced (ACSR/AZ) (Withdrawn 2007)
2.3 American National Standards Institute Standard:
B354 Terminology Relating to Uninsulated Metallic Electri-
H35.1M Alloy and Temper Designation Systems forAlumi-
cal Conductors
4
num
2.4 Other Standards:
1
This specification is under the jurisdiction of ASTM Committee B01 on
5
Electrical Conductors and is the direct responsibility of Subcommittee B01.07 on NBS Handbook 100—Copper Wire Tables
Conductors of Light Metals.
Current edition approved Oct. 15, 2012. Published January 2013. Originally
3. Terminology
approved in 1982. Last previous edition approved in 2005 as B711 – 05. DOI:
3.1 Definitions of Terms Specific to This Standard:
10.1520/B0711-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036.
5
3
The last approved version of this historical standard is referenced on Available from National Institute of Standards and Technology (NIST), 100
www.astm.org. Bureau Dr., Stop 3460, Gaithersburg, MD 20899-3460.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B711 − 12
3.1.1 AACSR—covered by this specification has five types 5.3 Steel core supplied in a stranded construction shall meet
of coated steel and one type of aluminum-clad steel core wire the requirements of Specification B500/B500M, if applicabl
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B711 − 05 B711 − 12
Standard Specification for
Concentric-Lay-Stranded Aluminum-Alloy Conductors, Steel
1
Reinforced (AACSR) (6201)
This standard is issued under the fixed designation B711; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers concentric-lay-stranded conductors made from round aluminum-alloy 6201-T81 hard: solution
heat treated, cold worked, and then artificially aged wire and round zinc-coated, Zn-5Al-MM coated, aluminum-coated, or
aluminum-clad steel core wire for use as overhead electric conductors (Explanatory Note 1 and Note 2).
NOTE 1—The alloy and temper designations conform to ANSI H35.1. Aluminum alloy 6201 corresponds to Unified Numbering System alloy A96201
in accordance with Practice E527.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the extent
referenced herein.
2
2.2 ASTM Standards:
B263 Test Method for Determination of Cross-Sectional Area of Stranded Conductors
B341/B341M Specification for Aluminum-Coated (Aluminized) Steel Core Wire for Aluminum Conductors, Steel Reinforced
3
(ACSR/AZ) (Withdrawn 2007)
B354 Terminology Relating to Uninsulated Metallic Electrical Conductors
B398/B398M Specification for Aluminum-Alloy 6201-T81 Wire for Electrical Purposes
B498/B498M Specification for Zinc-Coated (Galvanized) Steel Core Wire for Use in Overhead Electrical Conductors
B500/B500M Specification for Metallic Coated or Aluminum Clad Stranded Steel Core for Use in Overhead Electrical
Conductors
B502 Specification for Aluminum-Clad Steel Core Wire for Use in Overhead Electrical Aluminum Conductors
B606 Specification for High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Aluminum and Aluminum-Alloy
Conductors, Steel Reinforced
B802/B802M Specification for Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Aluminum Conductors,
Steel Reinforced (ACSR)
B803 Specification for High-Strength Zinc–5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead
Electrical Conductors
B957 Specification for Extra-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Overhead
Electrical Conductors
B958 Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-Coated
Steel Core Wire for Use in Overhead Electrical Conductors
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
1
This specification is under the jurisdiction of ASTM Committee B01 on Electrical Conductors and is the direct responsibility of Subcommittee B01.07 on Conductors
of Light Metals.
Current edition approved March 1, 2005Oct. 15, 2012. Published March 2005January 2013. Originally approved in 1982. Last previous edition approved in 19992005 as
B711 – 99.B711 – 05. DOI: 10.1520/B0711-05.10.1520/B0711-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B711 − 12
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
2.3 American National Standards Institute Standard:
4
H35.1M Alloy and Temper Designation Systems for Aluminum
2.4 Other Standards:
5
NBS Handbook 100—Copper Wire Tables
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 AACSR—covered by this specification has five types of coated steel and one type of aluminum-clad steel core wire which
are designated by abbreviati
...