ASTM A614-79

Specification for Special Requirements for Bolting Material for Nuclear and Other Special Applications (Withdrawn 1986)

General Information

• Status: Withdrawn
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.22 - Steel Forgings and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications

Standards Content (Sample)

9009276 0001552 967 D
ANSI/ASTM A 614 - 79
AMERICAN SOCIETY FOR TESTING AND MATERIALS
1918 Race St., Philadelphia, Pa, 19103
Reprinted from the Annual Book of ASTM Standards, Copyright ASTM
if not listed in the current combined Index will appear in the next edition
Standard Specification for
SPECIAL REQUIREMENTS FOR BOLTING MATERIAL FOR
NUCLEAR AND OTHER SPECIAL APPLICATIONS’
This standard is issued under the fixed designation A 614 the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval.
1. scope 2.1.3 American Society for Nondestructive
Testing Standard6
1,l This specification’ provides special re-
ASNT-TC- 1A Recommended Practice for
quirements for bolting material for use in nu-
Nondestmctive Testing Personnel Qualifica-
clear and other special applications. These spe-
tion and Certification.
cial applications are applicable to the specifi-
2.2 ASTM basic material specifications and
cations listed under 2.2. The requirements in
their ASME (SA) equivalents to which this
3.1 are mandatory under this specification. The
specification may be applied, include, but are
requirements in 3.2 are applicable as indicated
not limited to the following specifications:
when specified in the inquiry or purchase or-
193 Alloy-Steel and Stainless Steel Bolt-
ders.
ing Materials for High-Temperature Ser-
1.2 The requirements of this specification
vice’
are supplemental to the requirements of the
194 Carbon and Alloy Steel Nuts for Bolts
basic material specification.
for High-pressure and High-Temperature
1.3 Where any examination, test, or treat-
Service’
ment, included in this specification and speci-
307 Carbon Steel Externally and Inter-
fied in the order is also required by the basic
nally Threaded Standard Fasteners’
material specification, the examination, test, or
320 Alloy-Steel Bolting Materials for
treatment need be performed only once in such
Low-Temperature Service7
a way that the requirements of this specification
325 High-Strength Bolts for Structural
are met.
Joints’
Non-The values stated in inch-pound units are
354 Quenched and Tempered Alloy Steel
to be regarded as the standard.
2. Applicable Documents
’ This specification is under the jurisdiction of ASTM
Committee A-1 on Steel, Stainless Steel and Related Alloys
2.1 Reference Documents:
of Subcommittee A01.22 on
and is the direct responsibility
2.1.1 ASTM Standards:
Valves and Fittings.
A 275 Magnetic Particle Examination of
Current edition approved Aug. 31, 1979. hbiished Oc-
tober 1979. Originally published as A 614 - 73. Last previous
Steel Forgings3
- 76.
edition A 614
A 370 Methods and Definitions for Mechan-
’ For ASME Boiler and Pressure Vessel Code applications
see related Specification SA-614 in Section II of that Code.
ical Testing of Steel Products4
Annual Book of ASTM Standards, Part 5.
A 388 Recommended Practice for Ultra-
’Annual Book ofASTM Standards, Parts I, 2,3,4,5, and
sonic Examination of Heavy Steel Forg- 10.
’ Available from American Society of Mechanical Engi-
ing~~
neers, 345 E. 47th St., New York, N. Y. 10017.
2.1.2 American Society of Mechanical Engi-
e Available from American Society for Nondestructive
Testing, 914 Chicago Ave., Evanston, Ili. 60202.
neers Standard:5
Annual Book of ASTM Standards, Part I.
Boiler and Pressure Vessel Code-Sections
Annual Book of ASTM Standards, Parts 1 and 4.
II, III, and 17 (herein referred to as the “Code”). ‘Annual Book of ASTM Standards, Part 4.



k-d

---------------------- Page: 1 ----------------------
m 900927b 0003553 ôT3 m
A 614
length of the tension specimens and the area
Bolts, Studs, and Other Externally
under the notch of Charpy specimens shall be
Threaded Fasteners*
at least one diameter or thickness from the heat
A 453 Bolting Materials, High-Tempera-
treated end.
ture, 50 to 120 ksi Yield Strength, with
Expansion Coefficients Comparable to
6. RL Provisions for Repair by Welding
Austenitic Steels7
6.1 Weld repairs of bolts, studs, and nuts are
A 493 Stainless and Heat-Resisting Steel for
not permitted.
Cold Heading and Cold Forging-Bar
and Wire”
7. RM Elimination of Surface Defects
A 540 Alloy-Steel Bolting Materials for Spe-
7.1 Unacceptable surface defects on fmished
cial Applications7
bolts, studs, and nuts are not permitted, and
A 564 Hot-Rolled and Cold-Finished Age-
are cause for rejection.
Hardening Stainless and Heat-Resisting
Steel Bars and Shapes3
8. RO Certification and Identification
A 637 Precipitatiw Hardening Nickel Alloy
8.1 Certijkation:
Bars, Forgings, and Forging Stock for
8.1.1 Except as provided in 8.1.2 and 8.1.3,
High-Temperature Service3
the material
...