ASTM D83-84(2014)
(Specification)Standard Specification for Red Lead Pigment
Standard Specification for Red Lead Pigment
ABSTRACT
This specification covers four grades of red pigment commercially known as red lead. The pigment may be purchased in the dry form or as a paste in oil. Chemical analysis and coarse particle shall be tested to meet the requirements prescribed. Pigment, linseed oil, and moisture and other volatile matter in paste in oil shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers four grades of red pigment commercially known as red lead. The pigment may be purchased in the dry form or as a paste in oil.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D83 −84 (Reapproved 2014)
Standard Specification for
1
Red Lead Pigment
This standard is issued under the fixed designation D83; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
Dry red lead 20 lb (9.1 kg)
Raw linseed oil 5 pt (2.4 L)
1.1 This specification covers four grades of red pigment
Turpentine 2 gills (0.24 L)
commercially known as red lead. The pigment may be pur- Liquid drier 2 gills (0.24 L)
chased in the dry form or as a paste in oil.
3.2 Paste in Oil—The paste shall be made by thoroughly
grinding the specified pigment with linseed oil (Note 1). The
1.2 The values stated in inch-pound units are to be regarded
paste as shipped by the seller, and for three months thereafter,
as standard. The values given in parentheses are mathematical
shall not be caked in the container, and shall break up readily
conversions to SI units that are provided for information only
inoiltoformasmoothpaintofbrushingconsistency.Thepaste
and are not considered standard.
shall conform to the following requirements:
2. Referenced Documents
Pigment, % 92 to 94
2
Linseed oil, % 6.0 to 8.0
2.1 ASTM Standards:
Moisture and other volatile matter, max, % 0.5
D49 Test Methods of Chemical Analysis of Red Lead
Coarse particles and skins (total residue retained on 1.5
a No. 325 (45-µm) sieve), max, % of the dry pigment
D185 Test Methods for Coarse Particles in Pigments
D1208 Test Methods for Common Properties of Certain
Whenmixedasindicatedinthefollowingtable,theresulting
Pigments
paint, brushed on a smooth, vertical iron surface, shall dry hard
and elastic without running, streaking, or sagging:
3. Composition and Properties
Red lead paste 20 lb (9.1 kg)
Raw linseed oil 3 pt (1.4 L)
3.1 Dry Pigment—The pigment shall be made by roasting
Turpentine 2 gills (0.24 L)
litharge or metallic lead, or compounds of lead that yield
Liquid drier 2 gills (0.24 L)
litharge by heating, and shall consist entirely of oxides of lead,
NOTE 1—The storage of paste red lead in places of high temperature
free of adulterants. The four grades of pigment shall conform
shouldbeavoided,asheatacceleratesthetendencyofthismaterialtocake
to the following requirements:
or harden. Purchasers are cautioned that 85 % grade red lead should not be
True red lead (Pb O ), min, %:
bought in paste form. The 95 % grade, if made into paste, should be used
3 4
85 % grade 85
within a short period of time after grinding. When pure red lead paste is
95 % grade 95
to be stored for a considerable period of time, the 97 % or 98 % grade of
97 % grade 97
red lead should be specified. Therefore the manufacturer shall identify the
98 % grade 98
grade of red lead used in the paste and the date of manufacture.
Total impurities including moisture, water soluble 1.0
matter, and matter insoluble in a mixture of
nitric acid and hydrogen peroxide, max, %
4. Sampling
Lead monoxide, PbO remainder
Coarse particles (total residue retained on a 45-µm 1.0
4.1 Two samples shall be taken at random from different
(No. 325) sieve), max, %
packages from each lot, batch, day’s pack,
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D83 − 84 (Reapproved 2008) D83 − 84 (Reapproved 2014)
Standard Specification for
1
Red Lead Pigment
This standard is issued under the fixed designation D83; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—The units statement in subsection 1.2 was corrected editorially in July 2008.
1. Scope
1.1 This specification covers four grades of red pigment commercially known as red lead. The pigment may be purchased in
the dry form or as a paste in oil.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D49 Test Methods of Chemical Analysis of Red Lead
D185 Test Methods for Coarse Particles in Pigments
D1208 Test Methods for Common Properties of Certain Pigments
3. Composition and Properties
3.1 Dry Pigment—The pigment shall be made by roasting litharge or metallic lead, or compounds of lead that yield litharge by
heating, and shall consist entirely of oxides of lead, free of adulterants. The four grades of pigment shall conform to the following
requirements:
True red lead (Pb O ), min, %:
3 4
85 % grade 85
95 % grade 95
97 % grade 97
98 % grade 98
Total impurities including moisture, water soluble 1.0
matter, and matter insoluble in a mixture of
nitric acid and hydrogen peroxide, max, %
Lead monoxide, PbO remainder
Coarse particles (total residue retained on a 45-μm 1.0
(No. 325) sieve), max, %
When mixed as indicated in the following table, the resulting paint, brushed on a smooth vertical iron surface, shall dry hard
and elastic without running, streaking, or sagging:
Dry red lead 20 lb (9.1 kg)
Raw linseed oil 5 pt (2.4 L)
Turpentine 2 gills (0.24 L)
Liquid drier 2 gills (0.24 L)
3.2 Paste in Oil—The paste shall be made by thoroughly grinding the specified pigment with linseed oil (Note 1). The paste
as shipped by the seller, and for three months thereafter, shall not be caked in the container, and shall break up readily in oil to
form a smooth paint of brushing consistency. The paste shall conform to the following requirements:
Pigment, % 92 to 94
Linseed oil, % 6.0 to 8.0
Moisture and other volatile matter, max, % 0.5
Coarse particles and skins (total residue retained on 1.5
a No. 325 (45-μm) sieve), max, % of the dry pigment
1
This specification is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.31 on Pigment Specifications.
Current edition approved July 1, 2008Dec. 1, 2014. Published August 2008December 2014. Originally approved in 1921. Last previous edition approved in 20022008 as
ε1
D83 – 84 (2002).(2008) . DOI: 10.1520/D0083-84R08E01.10.1520/D0083-84R14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sst
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.