iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E636-02

(Guide)

Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E 706 (IH)

Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E 706 (IH)

SIGNIFICANCE AND USE
Practice E 185 describes a minimum program for the surveillance of reactor vessel materials, specifically mechanical property changes that occur in service. Guide E 636 may be applied in order to generate additional specific fracture toughness property information on radiation-induced property changes to better assist the determination of the optimum reactor vessel operation schemes.
SCOPE
1.1 This guide discusses test procedures that can be used in conjunction with, but not as alternatives to, those required by Practice E 185 for the surveillance of nuclear reactor vessels. The supplemental mechanical property tests outlined permit the acquisition of additional information on radiation-induced changes in fracture toughness, notch ductility, and tensile strength properties of the reactor vessel steels.
1.2 This guide provides recommendations for the preparation of test specimens for irradiation, and identifies special precautions and requirements for reactor surveillance operations and postirradiation test planning. Guidance on data reduction and computational procedures is also given. Reference is made to other ASTM test methods for the physical conduct of specimen tests and for raw data acquisition.

General Information

Status
Historical
Publication Date
09-Jun-2002
ICS
27.120.10 - Reactor engineering
Technical Committee
E10 - Nuclear Technology and Applications
Drafting Committee
E10.02 - Behavior and Use of Nuclear Structural Materials
Current Stage
Ref Project

Relations

Replaces
ASTM E636-95(2001) - Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E706 (IH)
Effective Date
10-Jun-2002
Replaced By
ASTM E636-09 - Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E 706 (IH)
Effective Date
01-Feb-2009
Referred By
ASTM E2215-19 - Standard Practice for Evaluation of Surveillance Capsules from Light-Water Moderated Nuclear Power Reactor Vessels
Effective Date
10-Jun-2002
Referred By
ASTM E509/E509M-21 - Standard Guide for In-Service Annealing of Light-Water Moderated Nuclear Reactor Vessels
Effective Date
10-Jun-2002
Referred By
ASTM E1005-21 - Standard Test Method for Application and Analysis of Radiometric Monitors for Reactor Vessel Surveillance
Effective Date
10-Jun-2002
Referred By
ASTM E185-21 - Standard Practice for Design of Surveillance Programs for Light-Water Moderated Nuclear Power Reactor Vessels
Effective Date
10-Jun-2002

Buy Standard

ASTM E636-02 - Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E 706 (IH)ASTM E636-02 - Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E 706 (IH)
PreviousNext
Guide
ASTM E636-02 - Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E 706 (IH)
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E 636 – 02
Standard Guide for
Conducting Supplemental Surveillance Tests for Nuclear
1
Power Reactor Vessels, E 706 (IH)
This standard is issued under the fixed designation E636; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope E1221 Test Method for Determining Plane-Strain Crack-
2
Arrest Fracture Toughness, K , of Ferritic Steels
1.1 This guide discusses test procedures that can be used in 1a
E1253 GuideforReconstitutionofIrradiatedCharpy-Sized
conjunction with, but not as alternatives to, those required by
3
Specimens
Practice E185 for the surveillance of nuclear reactor vessels.
E1820 Test Method for Measurement of Fracture Tough-
The supplemental mechanical property tests outlined permit
3
ness
the acquisition of additional information on radiation-induced
E1921 Test Method for Determination of Reference Tem-
changes in fracture toughness, notch ductility, and tensile
3
perature, T , for Ferritic Steels in the Transition Range
strength properties of the reactor vessel steels. 0
2.2 Other Standards:
1.2 This guide provides recommendations for the prepara-
ASME Boiler and Pressure Vessel Code, Section III, Sub-
tion of test specimens for irradiation, and identifies special
4
section NB (Class 1 Components)
precautions and requirements for reactor surveillance opera-
ISO 14556 Steel Charpy V-notch Pendulum Impact Test-
tions and postirradiation test planning. Guidance on data
5
Instrumented Test Method
reduction and computational procedures is also given. Refer-
ence is made to other ASTM test methods for the physical
3. Significance and Use
conduct of specimen tests and for raw data acquisition.
3.1 Practice E185 describes a minimum program for the
2. Referenced Documents surveillance of reactor vessel materials, specifically mechani-
calpropertychangesthatoccurinservice.GuideE636maybe
2.1 ASTM Standards:
2
applied in order to generate additional specific fracture tough-
E8 TestMethodsforTensionTestingofMetallicMaterials
ness property information on radiation-induced property
E23 Test Methods for Notched Bar Impact Testing of
2
changes to better assist the determination of the optimum
Metallic Materials
reactor vessel operation schemes.
E184 Practice for Effects of High-Energy Neutron Radia-
tion on the Mechanical Properties of Metallic Materials,
4. Supplemental Mechanical Property Test
3
E706 (IB)
4.1 Fracture Toughness Test—This test involves the dy-
E185 Practice for Conducting Surveillance Tests for Light
3 namicorstatictestingofafatigue-precrackedspecimenduring
Water Cooled Nuclear Power Reactor Vessels, E706 (IF)
which a record of force versus displacement is used to
E399 Test Method for Plane-Strain Fracture Toughness of
2 determine material fracture toughness properties such as the
Metallic Materials
plane strain fracture toughness (K ), the J-integral fracture
Ic
E482 Guide forApplication of NeutronTransport Methods
3 toughness (J ), the J-R curve, and the reference temperature
Ic
for Reactor Vessel Surveillance, E706 (IID)
(T ) (see Test Methods E399, E1820, and E1921, respec-
0
E560 Practice for Extrapolating Reactor Vessel Surveil-
3
tively). These test methods generally apply to elastic, elastic-
lance Dosimetry Results, E706 (IC)
2 plastic, or fully plastic behavior. The rate of specimen loading
E616 Terminology Relating to Fracture Testing
or stress intensity increase required for test classification as
E706 Master Matrix for Light-Water Reactor Pressure
3 static or dynamic is indicated by the referenced test methods.
Vessel Surveillance Standards, E706 (0)
Presently,onlyTestMethodsE399andE1820specifyalower
limit on loading rate for dynamic test performed in the linear
1
This guide is under the jurisdiction of ASTM Committee E10 on Nuclear elastic regime.
Technology and Applications and is the direct responsibility of Subcommittee
E10.02 on Behavior and Use of Nuclear Structural Materials.
4
Current edition approved June 10, 2002. Published September 2002. Originally
Available from American Society of Mechanical Engineers, 345 E. 47th St.,
published as E636–83. Last previous edition E636–95. New York, NY 10017.
2 5
Annual Book of ASTM Standards, Vol 03.01. Available from International Organization for Standardization (ISO), 1 rue de
3
Annual Book of ASTM Standards, Vol 12.02. Varembe, Case postale 56, CH-1211, Geneva 20, Switzerland.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E636–02
4.2 Precracked Charpy Impact Test—This test involves
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2956-23(Guide)
Standard Guide for Monitoring the Neutron Exposure of LWR Reactor Pressure Vessels

SIGNIFICANCE AND USE
4.1 Regulatory Requirements—The USA Code of Federal Regulations (10CFR Part 50, Appendix H) requires the implementation of a reactor vessel materials surveillance program for all operating LWRs. Other countries have similar regulations. The purpose of the program is to (1) monitor changes in the fracture toughness properties of ferritic materials in the reactor vessel beltline6 resulting from exposure to neutron irradiation and the thermal environment, and (2) make use of the data obtained from surveillance programs to determine the conditions under which the vessel can be operated with adequate margins of safety throughout its service life. Practice E185, derived mechanical property data, and (r, θ, z) physics-dosimetry data (derived from the calculations and reactor cavity and surveillance capsule measurements (1) using physics-dosimetry standards) can be used together with information in Guide E900 and Refs. 4, 11-18 to provide a relation between property degradation and neutron exposure, commonly called a “trend curve.” To obtain this trend curve at all points in the pressure vessel wall requires that the selected trend curve be used together with the appropriate (r, θ, z) neutron field information derived by use of this guide to accomplish the necessary interpolations and extrapolations in space and time.  
4.2 Neutron Field Characterization—The tasks required to satisfy the second part of the objective of 4.1 are complex and are summarized in Practice E853. In doing this, it is necessary to describe the neutron field at selected (r, θ, z) points within the pressure vessel wall. The description can be either time dependent or time averaged over the reactor service period of interest. This description can best be obtained by combining neutron transport calculations with plant measurements such as reactor cavity (ex-vessel) and surveillance capsule or RPV cladding (in-vessel) measurements, benchmark irradiations of dosimeter sensor materials, and knowledge of th...
SCOPE
1.1 This guide establishes the means and frequency of monitoring the neutron exposure of the LWR reactor pressure vessel throughout its operating life.  
1.2 The physics-dosimetry relationships determined from this guide may be used to estimate reactor pressure vessel damage through the application of Practice E693 and Guide E900, using fast neutron fluence (E > 1.0 MeV and E > 0.1 MeV), displacements per atom (dpa), or damage-function-correlated exposure parameters as independent exposure variables. Supporting the application of these standards are the E853, E944, E1005, and E1018 standards, identified in 2.1.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    12 pages
    English language
    sale 15% off
  • Guide
    12 pages
    English language
    sale 15% off
ASTM
ASTM E521-23(Practice)
Standard Practice for Investigating the Effects of Neutron Radiation Damage Using Charged-Particle Irradiation

SIGNIFICANCE AND USE
4.1 A characteristic advantage of charged-particle irradiation experiments is the precise, individual control over most of the important irradiation conditions such as dose, dose rate, temperature, and quantity of gases present. Additional attributes are the lack of induced radioactivation of specimens and, in general, a substantial compression of irradiation time, from years to hours, to achieve comparable damage as measured in displacements per atom (dpa). An important application of such experiments is the investigation of radiation effects that may occur in materials exposed to environments which do not currently exist, such as in first wall materials used in fusion reactors.  
4.2 The primary shortcoming of ion bombardments stems from the damage rate, or temperature dependences of the microstructural evolutionary processes in complex alloys, or both. It cannot be assumed that the time scale for damage evolution can be comparably compressed for all processes by increasing the displacement rate, even with a corresponding shift in irradiation temperature. In addition, the confinement of damage production to a thin layer just (often ∼1 μm) below the irradiated surface can present substantial complications. It must be emphasized, therefore, that these experiments and this practice are intended for research purposes and not for the certification or the qualification of materials.  
4.3 This practice relates to the generation of irradiation-induced changes in the microstructure of metals and alloys using charged particles. The investigation of mechanical behavior using charged particles is covered in Practice E821.
SCOPE
1.1 This practice provides guidance on performing charged-particle irradiations of metals and alloys, although many of the methods may also be applied to ceramic materials. It is generally confined to studies of microstructural and microchemical changes induced by ions of low-penetrating power that come to rest in the specimen. Density changes can be measured directly and changes in other properties can be inferred. This information can be used to estimate similar changes that would result from neutron irradiation. More generally, this information is of value in deducing the fundamental mechanisms of radiation damage for a wide range of materials and irradiation conditions.  
1.2 Where it appears, the word “simulation” should be understood to imply an approximation of the relevant neutron irradiation environment for the purpose of elucidating damage mechanisms. The degree of conformity can range from poor to nearly exact. The intent is to produce a correspondence between one or more aspects of the neutron and charged-particle irradiations such that fundamental relationships are established between irradiation or material parameters and the material response.  
1.3 The practice appears as follows:    
Section  
Apparatus  
4  
Specimen Preparation  
5 – 10  
Irradiation Techniques (including Helium Injection)  
11 – 12  
Damage Calculations  
13  
Postirradiation Examination  
14 – 16  
Reporting of Results  
17  
Correlation and Interpretation  
18 – 22  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    22 pages
    English language
    sale 15% off
  • Standard
    22 pages
    English language
    sale 15% off
ASTM
ASTM E2006-22(Guide)
Standard Guide for Benchmark Testing of Light Water Reactor Calculations

SIGNIFICANCE AND USE
4.1 This guide deals with the difficult problem of benchmarking neutron transport calculations carried out to determine fluences for plant specific reactor geometries. The calculations are necessary for fluence determination in locations important for material radiation damage estimation and which are not accessible to measurement. Typically, the most important application of such calculations is the estimation of fluence within the reactor vessel of operating light water reactors (LWR) to provide accurate estimates of the irradiation embrittlement of the base and weld metal in the vessel. The benchmark procedure must not only prove that calculations give reasonable results but that their uncertainties are propagated with due regard to the sensitivities of the different input parameters used in the transport calculations. Benchmarking is achieved by building up data bases of benchmark experiments that have different influences on uncertainty propagation. For example, in simple vessel wall mockups where measurements are made within a simulated reactor vessel wall, the integral effect of uncertainties in iron cross sections (absorption and elastic and inelastic scattering) are dominant and have been bounded by the agreement between calculation and measurement. For more complicated integral benchmarks, other factors such as: uncertainties in the distribution of fission sources, geometry, the energy-dependent cross sections, and the angular scattering distribution for elemental components of major materials in the neutron field (such as water and iron) may all be important uncertainty contributors. This guide describes general procedures for using neutron fields with known characteristics to corroborate the calculational methodology and nuclear data used to derive neutron field information from measurements of neutron sensor response.  
4.2 The bases for benchmark field referencing are usually irradiations performed in standard neutron fields with well-known energy spe...
SCOPE
1.1 This guide covers general approaches for benchmarking neutron transport calculations for pressure vessel surveillance programs in light water reactor systems. A companion guide (Guide E2005) covers use of benchmark fields for testing neutron transport calculations and cross sections in well controlled environments. This guide covers experimental benchmarking of neutron fluence calculations (or calculations of other exposure parameters such as dpa) in more complex geometries relevant to reactor pressure vessel surveillance. Particular sections of the guide discuss: the use of well-characterized benchmark neutron fields to provide an indication of the accuracy of the calculational methods and nuclear data when applied to typical cases; and the use of plant specific measurements to indicate bias in individual plant calculations. Use of these two benchmark techniques will serve to limit plant-specific calculational uncertainty, and, when combined with analytical uncertainty estimates for the calculations, will provide uncertainty estimates for reactor fluences with a higher degree of confidence.  
1.2 Although this guide and the companion guide, Guide E2005, are focused on power reactors, the principle of this guide is also applicable to non-power light water reactor pressure vessel surveillance programs.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM E185-21(Practice)
Standard Practice for Design of Surveillance Programs for Light-Water Moderated Nuclear Power Reactor Vessels

SIGNIFICANCE AND USE
4.1 Predictions of neutron radiation effects on pressure vessel steels are considered in the design of light-water moderated nuclear power reactors. Changes in system operating parameters often are made throughout the service life of the reactor vessel to account for radiation effects. Due to the variability in the behavior of reactor vessel steels, a surveillance program is warranted to monitor changes in the properties of actual vessel materials caused by long-term exposure to the neutron radiation and temperature environment of the reactor vessel. This practice describes the criteria that should be considered in planning and implementing surveillance test programs and points out precautions that should be taken to ensure that: (1) capsule exposures can be related to beltline exposures, (2) materials selected for the surveillance program are samples of those materials most likely to limit the operation of the reactor vessel, and (3) the test specimen types are appropriate for the evaluation of radiation effects on the reactor vessel.  
4.2 Guides E482 and E853 describe a methodology for estimation of neutron exposure obtained for reactor vessel surveillance programs. Regulators or other sources may describe different methods.  
4.3 The design of a surveillance program for a given reactor vessel must consider the existing body of data on similar materials in addition to the specific materials used for that reactor vessel. The amount of such data and the similarity of exposure conditions and material characteristics will determine their applicability for predicting radiation effects.
SCOPE
1.1 This practice covers procedures for designing a surveillance program for monitoring the radiation-induced changes in the mechanical properties of ferritic materials in light-water moderated nuclear power reactor vessels. New advanced light-water small modular reactor designs with a nominal design output of 300 MWe or less have not been specifically considered in this practice. This practice includes the minimum requirements for the design of a surveillance program, selection of vessel material to be included, and the initial schedule for evaluation of materials.  
1.2 This practice was developed for all light-water moderated nuclear power reactor vessels for which the predicted maximum fast neutron fluence (E > 1 MeV) exceeds 1 × 1021 neutrons/m 2  (1 × 1017 n/cm2) at the inside surface of the ferritic steel reactor vessel.  
1.3 This practice does not provide specific procedures for monitoring the radiation induced changes in properties beyond the design life. Practice E2215 addresses changes to the withdrawal schedule during and beyond the design life.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
Note 1: The increased complexity of the requirements for a light-water moderated nuclear power reactor vessel surveillance program has necessitated the separation of the requirements into three related standards. Practice E185 describes the minimum requirements for design of a surveillance program. Practice E2215 describes the procedures for testing and evaluation of surveillance capsules removed from a reactor vessel. Guide E636 provides guidance for conducting additional mechanical tests. A summary of the many major revisions to Practice E185 since its original issuance is contained in Appendix X2.
Note 2: This practice applies only to the planning and design of surveillance programs for reactor vessels designed and built after the effective date of this practice. Previous versions of Practice E185 apply to earlier reactor vessels. See Appendix X2.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Or...

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM E900-21(Guide)
Standard Guide for Predicting Radiation-Induced Transition Temperature Shift in Reactor Vessel Materials

SIGNIFICANCE AND USE
4.1 Operation of commercial power reactors must conform to pressure-temperature limits during heatup and cooldown to prevent over-pressurization at temperatures that might cause non-ductile behavior in the presence of a flaw. Radiation damage to the reactor vessel is compensated for by adjusting the pressure-temperature limits to higher temperatures as the neutron damage accumulates. The present practice is to base that adjustment on the TTS  produced by neutron irradiation as measured at the Charpy V-notch 41-J (30-ft·lbf) energy level. To establish pressure temperature operating limits during the operating life of the plant, a prediction of TTS  must be made.  
4.1.1 In the absence of surveillance data for a given reactor material (see Practice E185 and E2215), the use of calculative procedures are necessary to make the prediction. Even when credible surveillance data are available, it will usually be necessary to interpolate or extrapolate the data to obtain a TTS  for a specific time in the plant operating life. The embrittlement correlation presented herein has been developed for those purposes.  
4.2 Research has established that certain elements, notably copper (Cu), nickel (Ni), phosphorus (P), and manganese (Mn), cause a variation in radiation sensitivity of reactor pressure vessel steels. The importance of other elements, such as silicon (Si), and carbon (C), remains a subject of additional research. Copper, nickel, phosphorus, and manganese are the key chemistry parameters used in developing the calculative procedures described here.  
4.3 Only power reactor (PWR and BWR) surveillance data were used in the derivation of these procedures. The measure of fast neutron fluence used in the procedure is n/m2  (E > 1 MeV). Differences in fluence rate and neutron energy spectra experienced in power reactors and test reactors have not been accounted for in these procedures.
SCOPE
1.1 This guide presents a method for predicting values of reference transition temperature shift (TTS) for irradiated pressure vessel materials. The method is based on the TTS exhibited by Charpy V-notch data at 41-J (30-ft·lbf) obtained from surveillance programs conducted in several countries for commercial pressurized (PWR) and boiling (BWR) light-water cooled (LWR) power reactors. An embrittlement correlation has been developed from a statistical analysis of the large surveillance database consisting of radiation-induced TTS and related information compiled and analyzed by Subcommittee E10.02. The details of the database and analysis are described in a separate report (ADJE090015-EA).2,3 This embrittlement correlation was developed using the variables copper, nickel, phosphorus, manganese, irradiation temperature, neutron fluence, and product form. Data ranges and conditions for these variables are listed in 1.1.1. Section 1.1.2 lists the materials included in the database and the domains of exposure variables that may influence TTS but are not used in the embrittlement correlation.  
1.1.1 The range of material and irradiation conditions in the database for variables used in the embrittlement correlation:  
1.1.1.1 Copper content up to 0.4 %.
1.1.1.2 Nickel content up to 1.7 %.
1.1.1.3 Phosphorus content up to 0.03 %.
1.1.1.4 Manganese content within the range from 0.55 to 2.0 %.
1.1.1.5 Irradiation temperature within the range from 255 to 300°C (491 to 572°F).
1.1.1.6 Neutron fluence within the range from 1 × 1021 n/m2 to 2 × 1024 n/m2 (E> 1 MeV).
1.1.1.7 A categorical variable describing the product form (that is, weld, plate, forging).  
1.1.2 The range of material and irradiation conditions in the database for variables not included in the embrittlement correlation:  
1.1.2.1 A533 Type B Class 1 and 2, A302 Grade B, A302 Grade B (modified), and A508 Class 2 and 3. Also, European and Japanese steel grades that are equivalent to these ASTM Grades.
1.1.2.2 Submerged arc welds, shielded a...

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM E1167-15(2021)(Guide)
Standard Guide for Radiation Protection Program for Decommissioning Operations

SIGNIFICANCE AND USE
4.1 A program based on this guide will provide assurance to all concerned that the appropriate elements of radiation safety have been included to protect workers, the general public, and the environment in proximity to the decommissioning activities.  
4.2 Implementation of such a program will provide assurance to those agencies responsible for review or audit of the decommissioning project that the requirements for radiation protection have been addressed.
SCOPE
1.1 This guide provides instruction to the individual charged with the responsibility for developing and implementing the radiation protection program for decommissioning operations.  
1.2 This guide provides a basis for the user to develop radiation protection program documentation that will support both the radiological engineering and radiation safety aspects of the decommissioning project.  
1.3 This guide presents a description of those elements that should be addressed in a specific radiation protection plan for each decommissioning project. The plan would, in turn, form the basis for development of the implementation procedures that execute the intent of the plan.  
1.4 This guide applies to the development of radiation protection programs established to control exposures to radiation and radioactive materials associated with the decommissioning of nuclear facilities. The intent of this guide is to supplement existing radiation protection programs as they may pertain to decommissioning workers, members of the general public and the environment by describing the basic elements of a radiation protection program for decommissioning operations.  
1.5 This guide defines the elements of a radiation protection program that will ensure that the goals and objectives of a decommissioning activity are attained within the radiological limits and restrictions imposed by applicable governing and regulating agencies. The implementation of such a program will provide radiological protection to personnel and the environment. This guide should be used for developing the documentation that defines the intent and implementation of the radiation protection program for a specific decommissioning project.  
1.6 The Radiation Protection Program should address the following elements (see Note 1). This program shall be developed and maintained such that it satisfies all applicable Quality Assurance requirements developed for the decommissioning project.  
Note 1: If the site to be decommissioned is adjacent to an operating site, the radiological impact of the operating site must be considered in the development of the Radiation Protection Program for the decommissioning site.  
1.7 This guide does not address the subjects of emergency preparedness, safeguards, accountability, waste handling, storage, and transportation. Each of these issues has a direct interface with the radiation protection program. However, each constitutes a program in and of itself from program definition through implementation.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM E509/E509M-21(Guide)
Standard Guide for In-Service Annealing of Light-Water Moderated Nuclear Reactor Vessels

ABSTRACT
This guide covers the general procedures to be considered (as well as the demonstration of their effectiveness) for conducting in-service thermal anneals of light-water moderated nuclear reactor vessels. The purpose of this in-service annealing (heat treatment) is to improve the mechanical properties, especially fracture toughness, of the reactor vessel materials previously degraded by neutron embrittlement. This guide is designed to accommodate the variable response of reactor-vessel materials in post-irradiation annealing at various temperatures and different time periods, as well as to provide direction for the development of a vessel annealing procedure and a post-annealing vessel radiation surveillance program. Guidelines are provided to determine the post-anneal reference nil-ductility transition temperature (RTNDT), the Charpy V-notch upper shelf energy level, fracture toughness properties, and the predicted reembrittlement trend for these properties for reactor vessel beltline materials.
SIGNIFICANCE AND USE
3.1 Reactor vessels made of ferritic steels are designed with the expectation of progressive changes in material properties resulting from in-service neutron exposure. In the operation of light-water-cooled nuclear power reactors, changes in pressure-temperature (P – T) limits are made periodically during service life to account for the effects of neutron radiation on the ductile-to-brittle transition temperature material properties. If the degree of neutron embrittlement becomes large, the restrictions on operation during normal heat-up and cool down may become severe. Additional consideration should be given to postulated events, such as pressurized thermal shock (PTS). A reduction in the upper shelf toughness also occurs from neutron exposure, and this decrease may reduce the margin of safety against ductile fracture. When it appears that these situations could develop, certain alternatives are available that reduce the problem or postpone the time at which plant restrictions must be considered. One of these alternatives is to thermally anneal the reactor vessel beltline region, that is, to heat the beltline region to a temperature sufficiently above the normal operating temperature to recover a significant portion of the original fracture toughness and other material properties that were degraded as a result of neutron embrittlement.  
3.2 Preparation and planning for an in-service anneal should begin early so that pertinent information can be obtained to guide the annealing operation. Sufficient time should be allocated to evaluate the expected benefits in operating life to be gained by annealing; to evaluate the annealing method to be employed; to perform the necessary system studies and stress evaluations; to evaluate the expected annealing recovery and reembrittlement behavior; to develop and functionally test such equipment as may be required to do the in-service annealing; and, to train personnel to perform the anneal.  
3.3 Selection of the annealing te...
SCOPE
1.1 This guide covers the general procedures for conducting an in-service thermal anneal of a light-water moderated nuclear reactor vessel and demonstrating the effectiveness of the procedure. The purpose of this in-service annealing (heat treatment) is to improve the mechanical properties, especially fracture toughness, of the reactor vessel materials previously degraded by neutron embrittlement. The improvement in mechanical properties generally is assessed using Charpy V-notch impact test results, or alternatively, fracture toughness test results or inferred toughness property changes from tensile, hardness, indentation, or other miniature specimen testing (1).2  
1.2 This guide is designed to accommodate the variable response of reactor-vessel materials in post-irradiation annealing at various temperatures and different time periods. Certain inherent limiting factors must be considered in developing an annealing...

  • Guide
    12 pages
    English language
    sale 15% off
  • Guide
    12 pages
    English language
    sale 15% off
ASTM
ASTM E2005-21(Guide)
Standard Guide for Benchmark Testing of Reactor Dosimetry in Standard and Reference Neutron Fields

SIGNIFICANCE AND USE
3.1 This guide describes approaches for using neutron fields with well known characteristics to perform calibrations of neutron sensors, to intercompare different methods of dosimetry, and to corroborate procedures used to derive neutron field information from measurements of neutron sensor response.  
3.2 This guide discusses only selected standard and reference neutron fields which are appropriate for benchmark testing of light-water reactor dosimetry. The Standard Fields considered here include neutron source environments that closely approximate: a) the unscattered neutron spectra from  252Cf spontaneous fission; and b) the  235U thermal neutron induced fission. These standard fields were chosen for their spectral similarity to the high energy region (E > 2 MeV) of reactor spectra. The various categories of benchmark fields are defined in Terminology E170.  
3.3 There are other well known neutron fields that have been designed to mockup special environments, such as pressure vessel mockups in which it is possible to make dosimetry measurements inside of the steel volume of the “vessel.” When such mockups are suitably characterized, they are also referred to as benchmark fields. A variety of these engineering benchmark fields have been developed, or pressed into service, to improve the accuracy of neutron dosimetry measurement techniques. These special benchmark experiments are discussed in Guide E2006, and in Refs (1)4 and (2).
SCOPE
1.1 This guide covers facilities and procedures for benchmarking neutron measurements and calculations. Particular sections of the guide discuss: the use of well-characterized benchmark neutron fields to calibrate integral neutron sensors; the use of certified-neutron-fluence standards to calibrate radiometric counting equipment or to determine interlaboratory measurement consistency; development of special benchmark fields to test neutron transport calculations; use of well-known fission spectra to benchmark spectrum-averaged cross sections; and the use of benchmarked data and calculations to determine the uncertainties in derived neutron dosimetry results.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM E636-20(Guide)
Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels

SIGNIFICANCE AND USE
3.1 Practices E185 and E2215 describe a minimum program for the surveillance of reactor vessel materials, specifically mechanical property changes that occur in service. This guide may be applied to generate additional information on radiation-induced property changes to better assist the determination of the optimum reactor vessel operation schemes.
SCOPE
1.1 This guide discusses test procedures that can be used in conjunction with, but not as alternatives to, those required by Practices E185 and E2215 for the surveillance of nuclear reactor vessels. The supplemental mechanical property tests outlined permit the acquisition of additional information on radiation-induced changes in mechanical properties of the reactor vessel steels.  
1.2 This guide provides recommendations for the preparation of test specimens for irradiation, and identifies special precautions and requirements for reactor surveillance operations and post-irradiation test planning. Guidance on data reduction and computational procedures is also given. Reference is made to other ASTM test methods for the physical conduct of specimen tests and for raw data acquisition.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    7 pages
    English language
    sale 15% off
  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM E2215-19(Practice)
Standard Practice for Evaluation of Surveillance Capsules from Light-Water Moderated Nuclear Power Reactor Vessels

SIGNIFICANCE AND USE
4.1 Neutron radiation effects are considered in the design of light-water moderated nuclear power reactors. Changes in system operating parameters may be made throughout the service life of the reactor to account for these effects. A surveillance program is used to measure changes in the properties of actual vessel materials due to the irradiation environment. This practice describes the criteria that should be considered in evaluating surveillance program test capsules.  
4.2 Prior to the first issue date of this standard, the design of surveillance programs and the testing of surveillance capsules were both covered in a single standard, Practice E185. Between its provisional adoption in 1961 and its replacement linked to this standard, Practice E185 was revised many times (1966, 1970, 1973, 1979, 1982, 1993 and 1998). Therefore, capsules from surveillance programs that were designed and implemented under early versions of the standard were often tested after substantial changes to the standard had been adopted. For clarity, the standard practice for surveillance programs has been divided into the new Practice E185 that covers the design of new surveillance programs and this standard practice that covers the testing and evaluation of surveillance capsules. Modifications to the standard test program and supplemental tests are described in Guide E636.  
4.3 This practice is intended to cover testing and evaluation of all light-water moderated reactor pressure vessel surveillance capsules. The practice is applicable to testing of capsules from surveillance programs designed and implemented under all previous versions of Practice E185.  
4.4 The radiation-induced changes in the properties of the reactor pressure vessel are generally monitored by measuring the index temperatures, the upper-shelf energy and the tensile properties of specimens from the surveillance program capsules. The significance of these radiation-induced changes is described in Practice E185.  
4...
SCOPE
1.1 This practice covers the evaluation of test specimens and dosimetry from light water moderated nuclear power reactor pressure vessel surveillance capsules.  
1.2 Additionally, this practice provides guidance on reassessing withdrawal schedule for design life and operation beyond design life.  
1.3 This practice is one of a series of standard practices that outline the surveillance program required for nuclear reactor pressure vessels. The surveillance program monitors the irradiation-induced changes in the ferritic steels that comprise the beltline of a light-water moderated nuclear reactor pressure vessel.  
1.4 This practice along with its companion surveillance program practice, Practice E185, is intended for application in monitoring the properties of beltline materials in any light-water moderated nuclear reactor.2  
1.5 Modifications to the standard test program and supplemental tests are described in Guide E636.  
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off