ASTM G90-17
(Practice)Standard Practice for Performing Accelerated Outdoor Weathering of Materials Using Concentrated Natural Sunlight
Standard Practice for Performing Accelerated Outdoor Weathering of Materials Using Concentrated Natural Sunlight
SIGNIFICANCE AND USE
4.1 Results obtained from this practice can be used to compare the relative durability of materials subjected to the specific test cycle used. Results obtained from this practice can be considered as representative of natural weathering only when the degree of comparative performance has been established for the specific materials being tested.
4.2 The acceleration factor relating the rate of degradation in this accelerated exposure to the rate of degradation in a natural weathering exposure varies with the type and formulation of the material. Each material and formulation may respond differently to the increased level of irradiance and differences in temperature and humidity. Thus an acceleration factor determined for one material may not be applicable to other materials. For this reason, the use of a single acceleration factor is not recommended. Also, a different acceleration factor may be obtained by using different mirror types and configurations. Because of variability in test results for both accelerated and natural weathering exposures, results from a sufficient number of tests must be obtained to determine an acceleration factor for a material. Further, the acceleration factor is applicable to only one exposure location because results from natural weathering will vary due to seasonal or annual differences in climatic factors.
4.3 The relative durability of materials determined by this practice can be used to determine the relative durability of the materials exposed under natural weathering conditions provided the materials have similar acceleration factors. However, even if results from a specific accelerated test condition are found to be useful for comparing the durability of materials exposed in a particular exterior location, it cannot be assumed that they will be useful for determining the relative durability for a different location. The relative durability of materials in natural weathering exposure can be very different depending on the loc...
SCOPE
1.1 Fresnel-reflecting concentrators using the sun as source are utilized in the accelerated outdoor exposure testing of materials.
1.2 This practice covers a procedure for performing accelerated outdoor exposure testing of materials using a Fresnel-reflector accelerated outdoor weathering test machine. The apparatus (see Fig. 1 and Fig. 2) and guidelines are described herein to minimize the variables encountered during outdoor accelerated exposure testing.
1.3 This practice does not specify the exposure conditions best suited for the materials to be tested but is limited to the method of obtaining, measuring, and controlling the procedures and certain conditions of the exposure. Sample preparation, test conditions, and evaluation of results are covered in existing methods or specifications for specific materials.
1.4 The Fresnel-reflector accelerated outdoor exposure test machines described may be suitable for the determination of the relative durability of materials exposed to sunlight, heat, and moisture, provided the mechanisms of chemical or physical change, or both, which control the acceleration factors for the materials do not differ significantly.
1.5 This practice establishes uniform sample mounting and in-test maintenance procedures. Also included in the practice are standard provisions for maintenance of the machine and Fresnel-reflector mirrors to ensure cleanliness and durability.
1.6 This practice shall apply to specimens whose size meets the dimensions of the target board as described in 8.2.
1.7 For test machines currently in use, this practice may not apply to specimens exceeding 13 mm (1/2 in.) in thickness because cooling may be questionable.
1.8 Values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are provided for information only.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with it...
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: G90 − 17
Standard Practice for
Performing Accelerated Outdoor Weathering of Materials
1
Using Concentrated Natural Sunlight
This standard is issued under the fixed designation G90; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.8 Values stated in SI units are to be regarded as the
standard. The inch-pound units in parentheses are provided for
1.1 Fresnel-reflecting concentrators using the sun as source
information only.
are utilized in the accelerated outdoor exposure testing of
1.9 This standard does not purport to address all of the
materials.
safety concerns, if any, associated with its use. It is the
1.2 This practice covers a procedure for performing accel-
responsibility of the user of this standard to establish appro-
erated outdoor exposure testing of materials using a Fresnel-
priate safety, health, and environmental practices and deter-
reflector accelerated outdoor weathering test machine. The
mine the applicability of regulatory limitations prior to use.
apparatus (see Fig. 1 and Fig. 2) and guidelines are described
1.10 This international standard was developed in accor-
herein to minimize the variables encountered during outdoor
dance with internationally recognized principles on standard-
accelerated exposure testing.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
1.3 This practice does not specify the exposure conditions
mendations issued by the World Trade Organization Technical
best suited for the materials to be tested but is limited to the
Barriers to Trade (TBT) Committee.
method of obtaining, measuring, and controlling the proce-
dures and certain conditions of the exposure. Sample
2. Referenced Documents
preparation, test conditions, and evaluation of results are
2
covered in existing methods or specifications for specific
2.1 ASTM Standards:
materials.
D859 Test Method for Silica in Water
D1014 Practice for Conducting Exterior Exposure Tests of
1.4 The Fresnel-reflector accelerated outdoor exposure test
Paints and Coatings on Metal Substrates
machines described may be suitable for the determination of
D1435 Practice for Outdoor Weathering of Plastics
the relative durability of materials exposed to sunlight, heat,
3
D1898 Practice for Sampling of Plastics (Withdrawn 1998)
and moisture, provided the mechanisms of chemical or physi-
D4141 Practice for Conducting Black Box and Solar Con-
cal change, or both, which control the acceleration factors for
centrating Exposures of Coatings
the materials do not differ significantly.
D4364 Practice for Performing Outdoor Accelerated Weath-
1.5 This practice establishes uniform sample mounting and
ering Tests of Plastics Using Concentrated Sunlight
in-test maintenance procedures. Also included in the practice D4517 Test Method for Low-Level Total Silica in High-
are standard provisions for maintenance of the machine and
Purity Water by Flameless Atomic Absorption Spectros-
Fresnel-reflector mirrors to ensure cleanliness and durability. copy
D5722 Practice for Performing Accelerated Outdoor Weath-
1.6 This practice shall apply to specimens whose size meets
ering of Factory-Coated Embossed Hardboard Using Con-
the dimensions of the target board as described in 8.2.
centrated Natural Sunlight and a Soak-Freeze-Thaw Pro-
1.7 For test machines currently in use, this practice may not cedure
1
apply to specimens exceeding 13 mm ( ⁄2 in.) in thickness
E816 Test Method for Calibration of Pyrheliometers by
because cooling may be questionable. Comparison to Reference Pyrheliometers
1 2
This practice is under the jurisdiction of ASTM Committee G03 on Weathering For referenced ASTM standards, visit the ASTM website, www.astm.org, or
and Durabilityand is the direct responsibility of Subcommittee G03.02 on Natural contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Environmental Exposure Tests. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Dec. 1, 2017. Published December 2017. Originally the ASTM website.
3
approved in 1985. Last previous edition approved in 2010 as G90 – 10. DOI: The last approved version of this historical standard is referenced on
10.1520/G0090-17. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
G90 − 17
FIG. 1 Schematic of Fresnel-Reflecting Concentrator Accelerated Weathering Machine Single Axis Tracking
E824 Test
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: G90 − 10 G90 − 17
Standard Practice for
Performing Accelerated Outdoor Weathering of Nonmetallic
1
Materials Using Concentrated Natural Sunlight
This standard is issued under the fixed designation G90; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 Fresnel-reflecting concentrators using the sun as source are utilized in the accelerated outdoor exposure testing of
nonmetallic materials.
1.2 This practice covers a procedure for performing accelerated outdoor exposure testing of nonmetallic materials using a
Fresnel-reflector accelerated outdoor weathering test machine. The apparatus (see Fig. 1 and Fig. 2) and guidelines are described
herein to minimize the variables encountered during outdoor accelerated exposure testing.
1.3 This practice does not specify the exposure conditions best suited for the materials to be tested but is limited to the method
of obtaining, measuring, and controlling the procedures and certain conditions of the exposure. Sample preparation, test conditions,
and evaluation of results are covered in existing methods or specifications for specific materials.
1.4 The Fresnel-reflector accelerated outdoor exposure test machines described may be suitable for the determination of the
relative durability of materials exposed to sunlight, heat, and moisture, provided the mechanisms of chemical or physical change,
or both, which control the rates of acceleration factors for the materials do not differ significantly.
1.5 This practice establishes uniform sample mounting and in-test maintenance procedures. Also included in the practice are
standard provisions for maintenance of the machine and Fresnel-reflector mirrors to ensure cleanliness and durability.
1.6 This practice shall apply to specimens whose size meets the dimensions of the target board as described in 8.2.
1
1.7 For test machines currently in use, this practice may not apply to specimens exceeding 13 mm ( ⁄2 in.) in thickness because
cooling may be questionable.
1.8 Values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are provided for information
only.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.10 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D859 Test Method for Silica in Water
D1014 Practice for Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates
D1435 Practice for Outdoor Weathering of Plastics
3
D1898 Practice for Sampling of Plastics (Withdrawn 1998)
D4141 Practice for Conducting Black Box and Solar Concentrating Exposures of Coatings
1
This practice is under the jurisdiction of ASTM Committee G03 on Weathering and Durabilityand is the direct responsibility of Subcommittee G03.02 on Natural and
Environmental Exposure Tests.
Current edition approved June 1, 2010Dec. 1, 2017. Published June 2010December 2017. Originally approved in 1985. Last previous edition approved in 20052010 as
G90 – 05.G90 – 10. DOI: 10.1520/G0090-10.10.1520/G0090-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
G90 − 17
FIG. 1 Schematic of Fresnel-Reflecting Concentrator Accelerated Weathering Machine Single Axis Tracking
D4364 Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight
D4517 Test Method for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.