ASTM C568/C568M-15

Standard Specification for Limestone Dimension Stone

SCOPE
1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of limestone for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of limestone dimension stone.  
1.2 Dimension limestone shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically exclude molded, cast, or otherwise artificially aggregated units of composed fragments, and also crushed and broken stone.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

General Information

• Status: Historical
• Publication Date: 30-Nov-2015
• ICS: 91.100.15 - Mineral materials and products
• Technical Committee: C18 - Dimension Stone
• Drafting Committee: C18.03 - Material Specifications

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C568/C568M −15
Standard Specification for
1
Limestone Dimension Stone
This standard is issued under the fixed designation C568/C568M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope C1528 Guide for Selection of Dimension Stone
1.1 This specification covers the material characteristics,
3. Terminology
physical requirements, and sampling appropriate to the selec-
tion of limestone for general building and structural purposes.
3.1 Definitions—All definitions are in accordance with Ter-
Refer to Guides C1242 and C1528 for the appropriate selection minology C119.
and use of limestone dimension stone.
4. Classification
1.2 Dimension limestone shall include stone that is sawed,
cut, split, or otherwise finished or shaped and shall specifically
4.1 Dimension limestone shall be classified into three
exclude molded, cast, or otherwise artificially aggregated units
categories, generally descriptive of those limestones having
of composed fragments, and also crushed and broken stone.
densities in approximate ranges, as follows:
1.3 The values stated in either SI units or inch-pound units
4.1.1 I (Low-Density)—Limestone having a density ranging
3 3
are to be regarded separately as standard. The values stated in
from 110 through 135 lb/ft [1760 through 2160 kg/m ].
each system may not be exact equivalents; therefore, each
4.1.2 II (Medium-Density)—Limestone having a density
3
system shall be used independently of the other. Combining
greater than 135 and not greater than 160 lb/ft [2160 through
3
values from the two systems may result in non-conformance
2560 kg/m ].
with the standard.
4.1.3 III (High-Density)—Limestone having a density
3 3
greater than 160 lb/ft [2560 kg/m ].
2. Referenced Documents
2
2.1 ASTM Standards:
5. Physical Requirements
C97/C97M Test Methods for Absorption and Bulk Specific
Gravity of Dimension Stone
5.1 Limestone supplied under this specification shall con-
C99/C99M Test Method for Modulus of Rupture of Dimen-
form to the physical requirements listed in Table 1.
sion Stone
5.2 Limestone shall be sound, durable, and free of spalls,
C119 Terminology Relating to Dimension Stone
cracks, open seams, pits, or other defects that are likely to
C170/C170M Test Method for Compressive Strength of
impair its structural integrity in its intended use.
Dimension Stone
C241/C241M Test Method forAbrasion Resistance of Stone
5.3 The desired color and texture, with their permissible
Subjected to Foot Traffic
natural variations in material characteristics for all material to
C1242 Guide for Selection, Design, and Installation of
be produced for the project, shall be established by control
Dimension Stone Attachment Systems
samples. Select representative samples by viewing a sufficient
C1353 Test Method for Abrasion Resistance of Dimension
number of physical samples prior to production that show the
Stone Subjected to Foot Traffic Using a Rotary Platform
complete range of variations in color and texture of the
Abraser
limestone specified.
1
This specification is under the jurisdiction of ASTM Committee C18 on
6. Sampling
Dimension Stone and is the direct responsibility
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C568/C568M − 10 C568/C568M − 15
Standard Specification for
1
Limestone Dimension Stone
This standard is issued under the fixed designation C568/C568M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of
limestone for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use
of limestone dimension stone.
1.2 Dimension limestone shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically
exclude molded, cast, or otherwise artificially aggregated units of composed fragments, and also crushed and broken stone.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
2. Referenced Documents
2
2.1 ASTM Standards:
C97/C97M Test Methods for Absorption and Bulk Specific Gravity of Dimension Stone
C99/C99M Test Method for Modulus of Rupture of Dimension Stone
C119 Terminology Relating to Dimension Stone
C170/C170M Test Method for Compressive Strength of Dimension Stone
C241/C241M Test Method for Abrasion Resistance of Stone Subjected to Foot Traffic
C1242 Guide for Selection, Design, and Installation of Dimension Stone Attachment Systems
C1353 Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser
C1528 Guide for Selection of Dimension Stone
3. Terminology
3.1 Definitions—All definitions are in accordance with Terminology C119.
4. Classification
4.1 Dimension limestone shall be classified into three categories, generally descriptive of those limestones having densities in
approximate ranges, as follows:
3 3
4.1.1 I (Low-Density)—Limestone having a density ranging from 110 through 135 lb/ft [1760 through 2160 kg/m ].
3
4.1.2 II (Medium-Density)—Limestone having a density greater than 135 and not greater than 160 lb/ft [2160 through 2560
3
kg/m ].
3 3
4.1.3 III (High-Density)—Limestone having a density greater than 160 lb/ft [2560 kg/m ].
5. Physical Requirements
5.1 Limestone supplied under this specification shall conform to the physical requirements listed in Table 1.
5.2 Limestone shall be sound, durable, and free of spalls, cracks, open seams, pits, or other defects that are likely to impair its
structural integrity in its intended use.
1
This specification is under the jurisdiction of ASTM Committee C18 on Dimension Stone and is the direct responsibility of Subcommittee C18.03 on Material
Specifications.
Current edition approved Sept. 1, 2010Dec. 1, 2015. Published October 2010January 2016. Originally approved in 1965 .1965. Last previous edition approved in 20082010
as C568 – 08a.C568/C568M – 10. DOI: 10.1520/C0568_C0586M-10.10.1520/C0568_C0586M-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C568/C568M − 15
TABLE 1 Physical Requirements
NOTE 1—The values in Table 1 were established using samples prepared according to the individual test methods. Finishes, other than those specified
in the individual test methods, may result in a deviation from established values.
Test Requirements Classification Test Meth-
Physical Property
od(s)
Absorption by weight, max, % 12 I low-density C97/C97M
7.5 II medium-density
3 III high-density
3 3
Density, min, lb/ft [kg/m ] 110 [1760] I low-density C97/C97M
135 [2160] II medium-density
160 [2560] III high-density
Compressive strength, min, psi [MPa] 1800 [12] I low-density C170/C170M
4000 [28] II medium-density
8000 [55] III high-density
Modulus of rupture min, psi [MPa] 400 [2.8] I low-density C99/C99M
5
...