ASTM D2665-04ae2
(Specification)Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, hydrostatic burst resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings. A form of marking is also included. Plastic which does not meet the material requirements specified in Section 5 is excluded. Installation procedures are given in the Appendix.
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units given in parentheses may be approximate.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
e2
Designation: D 2665 – 04a
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent
1
Pipe and Fittings
This standard is issued under the fixed designation D2665; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Section 6.4 was editorially corrected in January 2005.
2
e NOTE—Table 3 was editorially corrected in May 2005.
1. Scope lic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to
1.1 This specification covers requirements and test methods
Plastics
for materials, dimensions and tolerances, pipe stiffness, crush
D1784 SpecificationforRigidPoly(VinylChloride)(PVC)
resistance, impact resistance, hydrostatic burst resistance, and
Compounds and Chlorinated Poly(Vinyl Chloride)
solvent cement for poly(vinyl chloride) plastic drain, waste,
(CPVC) Compounds
and vent pipe and fittings.Aform of marking is also included.
D2122 Test Method for Determining Dimensions of Ther-
Plasticwhichdoesnotmeetthematerialrequirementsspecified
moplastic Pipe and Fittings
in Section 5 is excluded. Installation procedures are given in
D2412 TestMethodforDeterminationofExternalLoading
the Appendix.
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.2 Thevaluesstatedininch-poundunitsaretoberegarded
D2444 Test Method for Determination of the Impact Re-
as the standard. The metric equivalents of inch-pound units
sistance ofThermoplastic Pipe and Fittings by Means of a
given in parentheses may be approximate.
Tup (Falling Weight)
1.3 Thetextofthisspecificationreferencesnotes,footnotes,
D2564 Specification for Solvent Cements for Poly(Vinyl
and appendixes which provide explanatory material. These
Chloride) (PVC) Plastic Piping Systems
notesandfootnotes(excludingthoseintablesandfigures)shall
D3311 Specification for Drain, Waste, and Vent (DWV)
not be considered as requirements of the specification.
Plastic Fittings Patterns
1.4 The following safety hazards caveat pertains only to the
D4396 SpecificationforRigidPoly(VinylChloride)(PVC)
test methods portion, Section 7, of this specification: This
and Chlorinated Poly(Vinyl Chloride) (CPVC) Com-
standard does not purport to address all of the safety concerns,
pounds for Plastic Pipe and Fittings Used in Nonpressure
if any, associated with its use. It is the responsibility of the user
Applications
of this standard to establish appropriate safety and health
F402 Practice for Safe Handling of Solvent Cements,
practices and determine the applicability of regulatory limita-
Primers,andCleanersUsedforJoiningThermoplasticPipe
tions prior to use.
and Fittings
2. Referenced Documents F412 Terminology Relating to Plastic Piping Systems
2
F1498 Specification for Taper Pipe Threads 60° for Ther-
2.1 ASTM Standards:
moplastic Pipe and Fittings
D618 Practice for Conditioning Plastics for Testing
F1866 Specification for Poly (Vinyl Chloride) (PVC) Plas-
D1599 Test Method for Resistance to Short-Time Hydrau-
tic Schedule 40 Drainage and DWV Fabricated Fittings
F2135 Specification for Molded Drain, Waste, and Vent-
(DWV) Short-Pattern Plastic Fittings
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
3. Terminology
CurrenteditionapprovedJune1,2004PublishedJune2004.Originallyapproved
in 1968. Last previous edition approved in 2004 as D2665–04.
3.1 Definitions—DefinitionsareinaccordancewithTermi-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
nology F412, and abbreviations are in accordance with Ter-
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
minology D1600, unless otherwise specified.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
e2
D 2665 – 04a
4. Significance and Use 6. Requirements
4.1 The requirements of this specification are intended to 6.1 General—The pipe and fittings shall be homogeneous
throughoutandfreeofvisiblecracks,holes,foreigninclusions,
provide pipe and fittings suitable for the drainage and venting
or other injurious defects. The pipe shall be as uniform as
of sewage and certain other liquid wastes.
commercially practicable in color, opacity, density, and other
NOTE 1—Industrial waste disposal lines should be installe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.