ASTM D6262-12

Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)

SCOPE
1.1 This specification covers requirements and methods of test for the material, dimensions, and workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from PAEK.
1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications are described by using the classification system given in Section 4.
1.3 This specification allows the use of key clad plastics (see Section 4).
1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1.
1.5 The following precautionary caveat pertains only to the test method portion Section 11, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—There is no known ISO equivalent to this standard.

General Information

• Status: Historical
• Publication Date: 14-Jan-2012
• ICS: 83.140.99 - Other rubber and plastics products
• Technical Committee: D20 - Plastics
• Drafting Committee: D20.15 - Thermoplastic Materials

Relations

• Replaces: ASTM D6262-05 - Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) (Withdrawn 2010)
• Effective Date: 15-Jan-2012
• Referred By: ASTM D8033-22 - Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
• Effective Date: 15-Jan-2012

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6262 −12
Standard Specification for
Extruded, Compression Molded, and Injection Molded Basic
1
Shapes of Poly(aryl ether ketone) (PAEK)
This standard is issued under the fixed designation D6262; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This specification in intended to be a means of calling out plastic product used in the fabrication of
end items or parts.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers requirements and methods of 2.1 ASTM Standards:
test for the material, dimensions, and workmanship, and the D256 Test Methods for Determining the Izod Pendulum
properties of extruded, compression molded, and injection Impact Resistance of Plastics
molded PAEK sheet, plate, rod, and tubular bar manufactured D618 Practice for Conditioning Plastics for Testing
from PAEK. D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced
1.2 The properties included in this specification are those
and Reinforced Plastics and Electrical Insulating Materi-
required for the compositions covered. Requirements neces-
als
sary to identify particular characteristics important to special-
D883 Terminology Relating to Plastics
ized applications are described by using the classification
D3892 Practice for Packaging/Packing of Plastics
system given in Section 4.
D4000 Classification System for Specifying Plastic Materi-
1.3 This specification allows the use of key clad plastics
als
(see Section 4).
D7209 Guide for Waste Reduction, Resource Recovery, and
Use of Recycled Polymeric Materials and Products
1.4 The values are stated in inch-pound units and are
regarded as the standard in all property and dimensional tables.
3. Terminology
For reference purposes, SI units are also included in Table 1.
3.1 Definitions:
1.5 The following precautionary caveat pertains only to the
1
3.1.1 plate, n—flat stock ⁄4 in. (6.4 mm), or greater.
test method portion Section 11, of this specification. This
3.1.2 recycled plastic shape, n—a product made from up to
standard does not purport to address all of the safety concerns,
100 % recycled plastic.
if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health
3.1.3 rod, n—solid cylindrical shape with a minimum diam-
1
practices and determine the applicability of regulatory limita-
eter of ⁄8 in. (3.2 mm).
tions prior to use.
1
3.1.4 sheet, n—flat stock less than and including ⁄4 in. (6.4
NOTE 1—There is no known ISO equivalent to this standard. mm) thickness.
3.1.5 tubular bar, n—annular shapes with minimum inside
3 1
diameterof ⁄8 in.(3.5mm)andminimumwallthicknessof ⁄16
1
This specification is under the jurisdiction of ASTM Committee D20 on
in. (1.6 mm).
Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic
Materials.
2
Current edition approved Jan. 15, 2012. Published February 2012. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approvedin1998.Lastpreviouseditionapprovedin2005asD6262 - 05,whichwas contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
withdrawn November 2010 and reinstated in January 2012. DOI: 10.1520/D6262- Standards volume information, refer to the standard’s Document Summary page on
12. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6262−12
3.1.6 virgin plastic shape, n—product that is produced from 4.5 Callout Designation—Aone-linesystemshallbeusedto
100 % plastic resin that has not been subjected to subsequent specify PAEK materials covered by this specification. The
melt processing. system uses predefined cells to refer to specific aspects of this
specification, as illustrated below:
3.2 Definitions of Terms Specific to This Standard:
4.5.1 Description:
3.2.1 For definitions of other technical terms pertaining to
4.5.1.1 Example 1—Extruded natural PAEK extruded rod:
plastics used in this specification, see Terminology D883 or
Guide D7209. CELL CALLOUT: S-PAEK0111
S-PAEK01 = Product made from PAEK resin in accordance with
4. Classification and Material
Table S-PAEK
1 = Unfilled class
4.1 Product shape and size as defined in the applicable
1 = General purpose grade product
purchase order.
4.5.1.2 Example 2—Compression molded natural PAEK
4.2 This specification covers product extruded as listed in
plate.
Table S-PAEK. Products include
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D6262–05 Designation: D6262 – 12
Standard Specification for
Extruded, Compression Molded, and Injection Molded Basic
1
Shapes of Poly(aryl ether ketone) (PAEK)
This standard is issued under the fixed designation D6262; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This specification in intended to be a means of calling out plastic product used in the fabrication of
end items or parts.
1. Scope*
1.1 This specification covers requirements and methods of test for the material, dimensions, and workmanship, and the
properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from
PAEK.
1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to
identify particular characteristics important to specialized applications may beare described by using the classification system
given in Section 4.
1.3 This specification allows the use of key clad plastics (see Section 4).
1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For
reference purposes, SI units are also included in Table 1.
1.5 The following precautionary caveat pertains only to the test method portion Section 11, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
NOTE1—There is no similar or equivalent ISO standard. 1—There is no known ISO equivalent to this standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D883 Terminology Relating to Plastics
D3892 Practice for Packaging/Packing of Plastics
D4000 Classification System for Specifying Plastic Materials
D5033Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics
2.2 ANSI Standards:
Z1.4-1993Sampling Procedures and Tables for Inspection byAttributes 7209 Guide for Waste Reduction, Resource Recovery,
and Use of Recycled Polymeric Materials and Products
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.20 on Plastic Products (Section
D20.20.02).
Current edition approved July 1, 2005. Published July 2005. Originally approved in 1998. Last previous edition approved in 2003 as D6262-98(2003). DOI:
10.1520/D6262-05.
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic Materials.
Current edition approved Jan. 15, 2012. Published February 2012. Originally approved in 1998. Last previous edition approved in 2005 as D6262-05, which was
withdrawn November 2010 and reinstated in January 2012. DOI: 10.1520/D6262-12.
2
As defined in Guide D5033.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,[e-mail] Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D6262 – 12
3. Terminology
3.1 Definitions:
1
3.1.1 plate, n—flat stock ⁄4 in. [6.4 mm], or greater. in. (6.4 mm), or greater.
3.1.2 recycled plastic shape, n—a product made from up to 100% recycled plastic.
1
3.1.3 rod, n—solid cylindrical shape with a minimum diameter of ⁄8 in. [3.2 mm]. in. (3.2 mm).
1
3.1.4 sheet, n—flat stock less than and including ⁄4 in. [6.4 mm] thickness. in. (6.4 mm) thickness.
3 1
3.1.5 tubular bar, n—annular shapes with minimum inside diameter of ⁄8 in. [3.5 mm] and minimum wall thickness of ⁄16 in.
1
[1.6 mm]. in. (3.5 mm) and minimum wall thi
...