ASTM D6511/D6511M-18
(Test Method)Standard Test Methods for Solvent Bearing Bituminous Compounds
Standard Test Methods for Solvent Bearing Bituminous Compounds
SIGNIFICANCE AND USE
3.1 These tests are useful in sampling and testing solvent bearing bituminous compounds to establish uniformity of shipments.
SCOPE
1.1 These test methods cover procedures for sampling and testing solvent bearing bituminous compounds for use in roofing and waterproofing.
1.2 The test methods appear in the following order:
Section
Sampling
4
Uniformity
5
Weight per gallon
6
Nonvolatile content
7
Solubility
8
Ash content
9
Water content
10
Consistency
11
Behavior at 60°C [140°F]
12
Pliability at –0°C [32°F]
13
Aluminum content
14
Reflectance of aluminum roof coatings
15
Strength of laps of rolled roofing adhered with roof adhesive
16
Adhesion to damp, wet, or underwater surfaces
17
Mineral stabilizers and bitumen
18
Mineral matter
19
Volatile organic content
20
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D6511/D6511M − 18
Standard Test Methods for
1
Solvent Bearing Bituminous Compounds
This standard is issued under the fixed designation D6511/D6511M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 These test methods cover procedures for sampling and 2.1 ASTM Standards:
testing solvent bearing bituminous compounds for use in C670 Practice for Preparing Precision and Bias Statements
roofing and waterproofing. for Test Methods for Construction Materials
D4 Test Method for Bitumen Content
1.2 The test methods appear in the following order:
D88 Test Method for Saybolt Viscosity
Section
D95 Test Method for Water in Petroleum Products and
Sampling 4
Bituminous Materials by Distillation
Uniformity 5
Weight per gallon 6
D140/D140M Practice for Sampling Asphalt Materials
Nonvolatile content 7
D146/D146M Test Methods for Sampling and Testing
Solubility 8
Ash content 9 Bitumen-Saturated Felts and Woven Fabrics for Roofing
Water content 10
and Waterproofing
Consistency 11
D224 Specification for Smooth-SurfacedAsphalt Roll Roof-
Behavior at 60°C [140°F] 12
3
Pliability at –0°C [32°F] 13 ing (Organic Felt) (Withdrawn 2002)
Aluminum content 14
D249 Specification for Asphalt Roll Roofing (Organic Felt)
Reflectance of aluminum roof coatings 15
3
Surfaced with Mineral Granules (Withdrawn 2002)
Strength of laps of rolled roofing adhered with roof adhesive 16
Adhesion to damp, wet, or underwater surfaces 17
D562 Test Method for Consistency of Paints Measuring
Mineral stabilizers and bitumen 18
KrebsUnit(KU)ViscosityUsingaStormer-TypeViscom-
Mineral matter 19
eter
Volatile organic content 20
D1475 Test Method for Density of Liquid Coatings, Inks,
1.3 The values stated in either SI units or inch-pound units
and Related Products
are to be regarded separately as standard. The values stated in
D2369 Test Method for Volatile Content of Coatings
each system may not be exact equivalents; therefore, each
D2824/D2824M Specification forAluminum-PigmentedAs-
system shall be used independently of the other. Combining
phalt Roof Coatings, Nonfibered, and Fibered without
values from the two systems may result in non-conformance
Asbestos
with the standard.
D4017 Test Method for Water in Paints and Paint Materials
1.4 This standard does not purport to address all of the
by Karl Fischer Method
safety concerns, if any, associated with its use. It is the
E1 Specification for ASTM Liquid-in-Glass Thermometers
responsibility of the user of this standard to establish appro-
E145 Specification for Gravity-Convection and Forced-
priate safety, health, and environmental practices and deter-
Ventilation Ovens
mine the applicability of regulatory limitations prior to use.
E200 Practice for Preparation, Standardization, and Storage
1.5 This international standard was developed in accor-
of Standard and Reagent Solutions for ChemicalAnalysis
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
3. Significance and Use
Development of International Standards, Guides and Recom-
3.1 These tests are useful in sampling and testing solvent
mendations issued by the World Trade Organization Technical
bearing bituminous compounds to establish uniformity of
Barriers to Trade (TBT) Committee.
shipments.
1 2
These test methods are under the jurisdiction of ASTM Committee D08 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Roofing and Waterproofing and are the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D08.05onSolvent-BearingBituminousCompoundsforRoofingandWaterproofing. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved May 1, 2018. Published May 2018. Originally the ASTM website.
3
approved in 2000. Last previous edition approved in 2011 as D6511/D6511M – 06 The last approved version of this historical standard is referenced on
ɛ1
(2011) . DOI: 10.1520/D6511_D6511M-18. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6511/D6511M − 18
4. Sampling
D = weight-per-gallon of sample, lb/gal. To convert units to
3
kg/m , multiply D by 119.83.
4.1 Determine the number of containers sampled to repre-
sent a shipment in accordance
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D6511/D6511M − 06 (Reapproved 2011) D6511/D6511M − 18
Standard Test Methods for
1
Solvent Bearing Bituminous Compounds
This standard is issued under the fixed designation D6511/D6511M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Units information and other information was editorially revised in July 2011.
1. Scope
1.1 These test methods cover procedures for sampling and testing solvent bearing bituminous compounds for use in roofing and
waterproofing.
1.2 The test methods appear in the following order:
Section
Sampling 4
Uniformity 5
Weight per gallon 6
Nonvolatile content 7
Solubility 8
Ash content 9
Water content 10
Consistency 11
Behavior at 60°C [140°F] 12
Pliability at –0°C [32°F] 13
Aluminum content 14
Reflectance of aluminum roof coatings 15
Strength of laps of rolled roofing adhered with roof adhesive 16
Adhesion to damp, wet, or underwater surfaces 17
Mineral stabilizers and bitumen 18
Mineral matter 19
Volatile organic content 20
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
D4 Test Method for Bitumen Content
D88 Test Method for Saybolt Viscosity
D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
D140D140/D140M Practice for Sampling BituminousAsphalt Materials
1
These test methods are under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and are the direct responsibility of Subcommittee D08.05 on
Solvent-Bearing Bituminous Compounds for Roofing and Waterproofing.
Current edition approved July 1, 2011May 1, 2018. Published July 2011May 2018. Originally approved in 2000. Last previous edition approved in 20062011 as
ɛ1
D6511D6511/D6511M – 06. 06 (2011) . DOI: 10.1520/D6511_D6511M-06R11E01.10.1520/D6511_D6511M-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6511/D6511M − 18
D146D146/D146M Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and
Waterproofing
3
D224 Specification for Smooth-Surfaced Asphalt Roll Roofing (Organic Felt) (Withdrawn 2002)
3
D249 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules (Withdrawn 2002)
D562 Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer
D1475 Test Method for Density of Liquid Coatings, Inks, and Related Products
D2369 Test Method for Volatile Content of Coatings
D2824D2824/D2824M Specification for Aluminum-Pigmented Asphalt Roof Coatings, Nonfibered, Asbestos Fibered, and
Fibered without Asbestos
D4017 Test Method for Water in Paints and Paint Materials by Karl Fischer Method
E1 Specification for ASTM Liquid-in-Glass Thermometers
E145 Specification for Gravity-Convection and Forced-Ventilation Ovens
E200 Practice for Preparation, Standardization, and Storage of Standard and Reagent Solutions for Chemical Analysis
3. Significance and Use
3.1 These tests are useful in samplin
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6511/D6511M − 18
Standard Test Methods for
1
Solvent Bearing Bituminous Compounds
This standard is issued under the fixed designation D6511/D6511M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 These test methods cover procedures for sampling and 2.1 ASTM Standards:
testing solvent bearing bituminous compounds for use in C670 Practice for Preparing Precision and Bias Statements
roofing and waterproofing. for Test Methods for Construction Materials
D4 Test Method for Bitumen Content
1.2 The test methods appear in the following order:
D88 Test Method for Saybolt Viscosity
Section
D95 Test Method for Water in Petroleum Products and
Sampling 4
Uniformity 5 Bituminous Materials by Distillation
Weight per gallon 6
D140/D140M Practice for Sampling Asphalt Materials
Nonvolatile content 7
D146/D146M Test Methods for Sampling and Testing
Solubility 8
Ash content 9 Bitumen-Saturated Felts and Woven Fabrics for Roofing
Water content 10
and Waterproofing
Consistency 11
D224 Specification for Smooth-Surfaced Asphalt Roll Roof-
Behavior at 60°C [140°F] 12
3
Pliability at –0°C [32°F] 13
ing (Organic Felt) (Withdrawn 2002)
Aluminum content 14
D249 Specification for Asphalt Roll Roofing (Organic Felt)
Reflectance of aluminum roof coatings 15
3
Surfaced with Mineral Granules (Withdrawn 2002)
Strength of laps of rolled roofing adhered with roof adhesive 16
Adhesion to damp, wet, or underwater surfaces 17 D562 Test Method for Consistency of Paints Measuring
Mineral stabilizers and bitumen 18
Krebs Unit (KU) Viscosity Using a Stormer-Type Viscom-
Mineral matter 19
eter
Volatile organic content 20
D1475 Test Method for Density of Liquid Coatings, Inks,
1.3 The values stated in either SI units or inch-pound units
and Related Products
are to be regarded separately as standard. The values stated in
D2369 Test Method for Volatile Content of Coatings
each system may not be exact equivalents; therefore, each
D2824/D2824M Specification for Aluminum-Pigmented As-
system shall be used independently of the other. Combining
phalt Roof Coatings, Nonfibered, and Fibered without
values from the two systems may result in non-conformance
Asbestos
with the standard.
D4017 Test Method for Water in Paints and Paint Materials
1.4 This standard does not purport to address all of the
by Karl Fischer Method
safety concerns, if any, associated with its use. It is the
E1 Specification for ASTM Liquid-in-Glass Thermometers
responsibility of the user of this standard to establish appro-
E145 Specification for Gravity-Convection and Forced-
priate safety, health, and environmental practices and deter-
Ventilation Ovens
mine the applicability of regulatory limitations prior to use.
E200 Practice for Preparation, Standardization, and Storage
1.5 This international standard was developed in accor-
of Standard and Reagent Solutions for Chemical Analysis
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
3. Significance and Use
Development of International Standards, Guides and Recom-
3.1 These tests are useful in sampling and testing solvent
mendations issued by the World Trade Organization Technical
bearing bituminous compounds to establish uniformity of
Barriers to Trade (TBT) Committee.
shipments.
1 2
These test methods are under the jurisdiction of ASTM Committee D08 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Roofing and Waterproofing and are the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D08.05 on Solvent-Bearing Bituminous Compounds for Roofing and Waterproofing. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved May 1, 2018. Published May 2018. Originally the ASTM website.
3
approved in 2000. Last previous edition approved in 2011 as D6511/D6511M – 06 The last approved version of this historical standard is referenced on
ɛ1
(2011) . DOI: 10.1520/D6511_D6511M-18. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6511/D6511M − 18
4. Sampling
D = weight-per-gallon of sample, lb/gal. To convert units to
3
kg/m , multiply D by 119.83.
4.1 Determine the number of containers sampled to repre-
sent a shipment in accordance with Practice D140/D140M.
6.3.2 Calculate the specific gravity of the sample as follows:
4.2 Open the original containe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.