ASTM F2159-21

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Crosslinked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

ABSTRACT
This specification establishes requirements for sulfone plastic insert fittings utilizing a copper crimp ring for SDR9 cross-linked polyethylene (PEX) tubing for cold- and hot-water distribution systems. Material for fitting shall be molded from sulfone plastic. Molded part shall not crack, split, or shatter and be free of visible splay. Fittings shall be tested for performance requirements such as hydrostatic burst, hydrostatic sustained pressure strength, thermocycling, excessive temperature-pressure capability, dimensions, workmanship, finish, appearance, assembly, crimp joint, and insert crush test.
SCOPE
1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings, or alternate stainless steel clamps for four sizes Nominal Tubing Sizes (NTS) (3/8 , 1/2 , 3/4 , and 1) of cross-linked polyethylene (PEX) tubing that meet the requirements for Specification F876 or Specification F3253, or polyethylene of raised temperature (PE-RT) tubing that meet the requirements of Specification F2623 or Specification F2769. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180 °F (82 °C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings.  
1.1.1 When used with PEX tubing in accordance with Specification F876, the fittings covered by this specification are intended for use in, but not limited to, residential and commercial, hot- and cold-potable water distribution systems, reclaimed water, fire protection, municipal water service lines, radiant heating and cooling systems, hydronic distribution systems, snow and ice melting systems, geothermal ground loops, district heating, turf conditioning, compressed air distribution, and building services pipe.  
1.1.2 When used with PEX tubing in accordance with Specification F3253, the fittings covered by this specification are intended for use in residential and commercial hydronic heating and cooling systems.  
1.1.3 When used with PE-RT tubing in accordance with Specification F2769, the fittings covered by this specification are intended for use in residential and commercial, hot- and cold-potable water distribution systems.  
1.1.4 When used with PE-RT tubing in accordance with Specification F2623, the fittings covered by this specification are intended for use in general fluid transport, including hydronics and irrigations systems.  
1.2 Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings.  
1.3 The following is an index of the appendix in this specification:    
GO/NO-GO Crimp Gauges  
Appendix X1  
1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 30-Apr-2021
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.10 - Fittings

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2159 − 21 An American National Standard
Standard Specification for
Plastic Insert Fittings Utilizing a Copper Crimp Ring, or
Alternate Stainless Steel Clamps for SDR9 Crosslinked
Polyethylene (PEX) Tubing and SDR9 Polyethylene of
1
Raised Temperature (PE-RT) Tubing
This standard is issued under the fixed designation F2159; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* are intended for use in general fluid transport, including
hydronics and irrigations systems.
1.1 This specification establishes requirements for sulfone
1.2 Included are the requirements for material, molded part
plastic insert fittings and copper crimp rings, or alternate
properties, performance, workmanship, dimensions, and mark-
stainless steel clamps for four sizes Nominal Tubing Sizes
3 1 3
ings to be used on the fittings and rings.
(NTS) ( ⁄8, ⁄2, ⁄4, and 1) of cross-linked polyethylene (PEX)
tubing that meet the requirements for Specification F876 or
1.3 The following is an index of the appendix in this
Specification F3253, or polyethylene of raised temperature
specification:
(PE-RT) tubing that meet the requirements of Specification
GO/NO-GO Crimp Gauges Appendix X1
F2623 or Specification F2769. These fittings are intended for
1.4 Units—The values stated in inch-pound units are to be
use in 100 psi (690 kPa) cold- and hot-water distribution
regarded as standard. The values given in parentheses are
systems operating at temperatures up to and including 180 °F
mathematical conversions to SI units that are provided for
(82 °C). Included are the requirements for material, molded
information only and are not considered standard.
part properties, performance, workmanship, dimensions, and
1.5 The following precautionary caveat pertains only to the
markings to be used on the fittings and rings.
test method portions, Sections 11 and 12, of this specification.
1.1.1 When used with PEX tubing in accordance with
This standard does not purport to address all of the safety
Specification F876, the fittings covered by this specification are
concerns, if any, associated with its use. It is the responsibility
intended for use in, but not limited to, residential and
of the user of this standard to establish appropriate safety,
commercial, hot- and cold-potable water distribution systems,
health, and environmental practices and determine the appli-
reclaimed water, fire protection, municipal water service lines,
cability of regulatory limitations prior to use.
radiant heating and cooling systems, hydronic distribution
1.6 This international standard was developed in accor-
systems, snow and ice melting systems, geothermal ground
dance with internationally recognized principles on standard-
loops, district heating, turf conditioning, compressed air
ization established in the Decision on Principles for the
distribution, and building services pipe.
Development of International Standards, Guides and Recom-
1.1.2 When used with PEX tubing in accordance with
mendations issued by the World Trade Organization Technical
Specification F3253, the fittings covered by this specification
Barriers to Trade (TBT) Committee.
are intended for use in residential and commercial hydronic
heating and cooling systems.
2. Referenced Documents
1.1.3 When used with PE-RT tubing in accordance with
2
Specification F2769, the fittings covered by this specification 2.1 ASTM Standards:
are intended for use in residential and commercial, hot- and D618 Practice for Conditioning Plastics for Testing
cold-potable water distribution systems. D1598 Test Method for Time-to-Failure of Plastic Pipe
1.1.4 When used with PE-RT tubing in accordance with Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic
Specification F2623, the fittings covered by this specification
Pressure of Plastic Pipe, Tubing, and Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved May 1, 2021. Published May 2021. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved 2001. Last previous edition approved in 2020 as F2159-20. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F2159-21. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2159 − 20 F2159 − 21 An American National Standard
Standard Specification for
Plastic Insert Fittings Utilizing a Copper Crimp Ring, or
Alternate Stainless Steel Clamps for SDR9 Crosslinked
Polyethylene (PEX) Tubing and SDR9 Polyethylene of
1
Raised Temperature (PE-RT) Tubing
This standard is issued under the fixed designation F2159; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings, or alternate stainless steel
3 1 3
clamps for four sizes Nominal Tubing Sizes (NTS) ( ⁄8, ⁄2, ⁄4, and 1) of cross-linked polyethylene (PEX) tubing that meet the
requirements for Specification F876 or Specification F3253, or polyethylene of raised temperature (PE-RT) tubing that meet the
requirements of Specification F2623 or Specification F2769. These fittings are intended for use in 100 psi (690 kPa) cold- and
hot-water distribution systems operating at temperatures up to and including 180 °F (82 °C). Included are the requirements for
material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings.
1.1.1 When used with PEX tubing in accordance with Specification F876, the fittings covered by this specification are intended
for use in, but not limited to, residential and commercial, hot- and cold-potable water distribution systems, reclaimed water, fire
protection, municipal water service lines, radiant heating and cooling systems, hydronic distribution systems, snow and ice melting
systems, geothermal ground loops, district heating, turf conditioning, compressed air distribution, and building services pipe.
1.1.2 When used with PEX tubing in accordance with Specification F3253, the fittings covered by this specification are intended
for use in residential and commercial hydronic heating and cooling systems.
1.1.3 When used with PE-RT tubing in accordance with Specification F2769, the fittings covered by this specification are intended
for use in residential and commercial, hot- and cold-potable water distribution systems.
1.1.4 When used with PE-RT tubing in accordance with Specification F2623, the fittings covered by this specification are intended
for use in general fluid transport, including hydronics and irrigations systems.
1.2 Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to
be used on the fittings and rings.
1.3 The following is an index of the appendix in this specification:
GO/NO-GO Crimp Gauges Appendix X1
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Nov. 1, 2020May 1, 2021. Published November 2020May 2021. Originally approved 2001. Last previous edition approved in 20192020 as
F2159-19a.-20. DOI: 10.1520/F2159-20.10.1520/F2159-21.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2159 − 21
1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification. This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory
limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1598 Test Method for Time-to-Failure
...