ASTM C1344-97(2013)
(Test Method)Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Single-Standard Gas Source Mass Spectrometer Method (Withdrawn 2020)
Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Single-Standard Gas Source Mass Spectrometer Method (Withdrawn 2020)
SIGNIFICANCE AND USE
5.1 Uranium hexafluoride is a basic material used to prepare nuclear reactor fuel. To be suitable for this purpose, the material must meet the criteria for isotopic composition. This test method is designed to determine whether the material meets the requirements described in Specifications C787 and C996.
5.2 ASTM Committee C-26 Safeguards Statement:
5.2.1 The material (uranium hexafluoride) to which this test method applies is subject to the nuclear safeguards regulations governing its possession and use. The analytical procedure in this test method has been designated as technically acceptable for generating safeguards accountability data.
5.2.2 When used in conjunction with appropriate certified reference materials (CRMs), this procedure can demonstrate traceability to the national measurement base. However, adherence to this procedure does not automatically guarantee regulatory acceptance of the regulatory safeguards measurements. It remains the sole responsibility of the user of this test method to ensure that its application to safeguards has the approval of the proper regulatory authorities.
SCOPE
1.1 This test method covers the isotopic analysis of uranium hexafluoride (UF6) and may be used for the entire range of 235U isotopic compositions for which standards are available.
1.2 This test method is applicable to the determination of the isotopic relationship between two UF6 samples. If the abundance of a specific isotope of one sample (the standard) is known, its abundance in the other can be determined. This test method is flexible in that the number of times a given material is admitted to the ion source may be adjusted to the minimum required for a specified precision level.
1.3 The sensitivity with which differences between two materials can be detected depends on the measuring system used, but ratio-measuring devices can generally read ratio-of-mol ratio differences as small as 0.0001.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 7.
WITHDRAWN RATIONALE
This test method covers the isotopic analysis of uranium hexafluoride (UF6) and may be used for the entire range of 235U isotopic compositions for which standards are available.
Formerly under the jurisdiction of Committee C26 on Nuclear Fuel Cycle, this test method was withdrawn in January 2020. This standard is being withdrawn without replacement due to its limited use by industry.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1344 −97 (Reapproved 2013)
Standard Test Method for
Isotopic Analysis of Uranium Hexafluoride by Single-
Standard Gas Source Mass Spectrometer Method
This standard is issued under the fixed designation C1344; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 Other Document:
USEC-651, Uranium Hexafluoride: A Manual of Good
1.1 Thistestmethodcoverstheisotopicanalysisofuranium
Handling Practices
hexafluoride (UF ) and may be used for the entire range of
U isotopic compositions for which standards are available.
3. Terminology
1.2 This test method is applicable to the determination of
3.1 Definitions of Terms Specific to This Standard:
the isotopic relationship between two UF samples. If the
3.1.1 drop through, n—a measurement of the amount of the
abundance of a specific isotope of one sample (the standard) is
238 + 235 +
UF ion beam that can be passed through the UF
5 5
known, its abundance in the other can be determined.This test
235 +
collector slit and measured on the UF collector, stated as
method is flexible in that the number of times a given material
238 +
a percentage of the total UF signal.
is admitted to the ion source may be adjusted to the minimum
3.1.2 memory corrections, n—corrections applied to the
required for a specified precision level.
sample analysis results for memory effects.
1.3 The sensitivity with which differences between two
3.1.3 memory effect, n—the inability of the mass spectrom-
materials can be detected depends on the measuring system
eter to omit completely the isotopic composition of the sample
used, but ratio-measuring devices can generally read ratio-of-
analyzed previously from attributing to the results of further
mol ratio differences as small as 0.0001.
samples analyzed.
1.4 The values stated in SI units are to be regarded as
3.1.4 normal isotopic abundance material, n—UF havinga
standard. No other units of measurement are included in this
value of 0.711 weight percent (wt%) U.
standard.
235 238
3.1.5 ratio-of-mol-ratios, n—the mol ratio ( U/ U) of
1.5 This standard does not purport to address all of the
the sample divided by the mol ratio of the standard, or the
safety concerns, if any, associated with its use. It is the
inverseconditionofthemolratioofthestandarddividedbythe
responsibility of the user of this standard to establish appro-
mol ratio of the sample.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. Specific hazards
4. Summary of Test Method
statements are given in Section 7.
4.1 Test Method—The unknown sample and a standard with
2. Referenced Documents
an isotopic composition close to that of the sample are
+
introduced in sequence into the Neir mass spectrometer. UF
2.1 ASTM Standards: 5
ions of the isotopes are focused through a mass-resolving
C787Specification for Uranium Hexafluoride for Enrich-
collector slit and onto a faraday cup collector. Measurements
ment
235 + +
are made of UF to the total of the other UF isotopes.
5 5
C996Specification for Uranium Hexafluoride Enriched to
Withtheknowncompositionofthestandard,calculationofthe
Less Than 5 % U
U composition of the sample can be determined.
5. Significance and Use
ThistestmethodisunderthejurisdictionofASTMCommitteeC26onNuclear
Fuel Cycle and is the direct responsibility of Subcommittee C26.05 on Methods of
5.1 Uraniumhexafluorideisabasicmaterialusedtoprepare
Test.
nuclear reactor fuel. To be suitable for this purpose, the
CurrenteditionapprovedJuly1,2013.PublishedJuly2013.Originallyapproved
ε1.
in 1997. Last previous edition approved in 2008 as C1344–97 (2008) DOI: material must meet the criteria for isotopic composition. This
10.1520/C1344-97R13.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on Available from U.S. Enrichment Corporation, 6903 Rockledge Dr., Bethesda,
the ASTM website. MD 20817, http://www.usec.com.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
C1344−97 (2013)
test method is designed to determine whether the material tolerated. The memory characteristics of a spectrometer must
meets the requirements described in Specifications C787 and be established from periodic measurement of the effect. Cur-
C996. rent memory values usually will apply until the ion source is
replaced, repairs are made on the sample inlet system, or the
5.2 ASTM Committee C-26 Safeguards Statement:
instrument is refocused so the flow rate of UF is altered
5.2.1 The material (uranium hexafluoride) to which this test
significantly.
method applies is subject to the nuclear safeguards regulations
6.1.1.8 Thecomputercontrolofthemassspectrometermust
governing its possession and use. The analytical procedure in
allow the operator to monitor parameters of the spectrometer
this test method has been designated as technically acceptable
and check other operating conditions. The development of an
for generating safeguards accountability data.
interactive program allows input of sample information, per-
5.2.2 When used in conjunction with appropriate certified
forms necessary calculations, makes memory corrections, and
reference materials (CRMs), this procedure can demonstrate
records data. Flexibility of the interactive program allows
traceabilitytothenationalmeasurementbase.However,adher-
pausing of the instrument for adjustment or restart capability,
ence to this procedure does not automatically guarantee regu-
or both. Suggested methods of analysis checks include the
latory acceptance of the regulatory safeguards measurements.
standard deviation (SD) on individual data points, linearity of
Itremainsthesoleresponsibilityoftheuserofthistestmethod
thedataset,andacheckofsourcepressuredifferencesbetween
to ensure that its application to safeguards has the approval of
thestandardandsamplethatcanbemonitoredbythecomputer
the proper regulatory authorities.
program. Manifold valve actuation, conditioning time, and
pump-out time are features of the computer control program.
6. Apparatus
6.1 Neir Mass Spectrometer,withthefollowingfeaturesand
7. Hazards
capabilities:
7.1 Since UF is radioactive, toxic, and highly reactive,
6.1.1 Asingle-focusing spectrometer, with a 127-mm mini- 6
especially with reducing substances and moisture (see USEC-
mum deflection radius, is satisfactory when equipped and
651), appropriate facilities and practices for analysis must be
focused as follows:
provided.
6.1.1.1 The sample inlet system must have two sample
holders, to which UF containers can be attached, and the
8. Procedure
necessary valves to evacuate the sample lines through which
the sample and standard are introduced. The sample inlet
8.1 Calibration of Isotopic Standards:
systemshouldbenickelorMonelforusewithcorrosivegases,
8.1.1 One working standard is required for the analysis of a
and should have minimum volume.
sample at any specific concentration of any isotope. Two
6.1.1.2 A single adjustable leak, operated by an automatic
working standards are required to determine memory correc-
leak control mechanism for admitting the sample into the
tions. Memory can be measured more precisely with a large
spectrometer ion source, is preferred.
difference between two working standards, but the adverse
6.1.1.3 The pumping system of the spectrometer analyzer
effect of introducing wide concentration ranges into the mass
−8
tube must maintain a pressure below 5×10 torr with sample
spectrometer must be considered. Ideally, the values obtained
flowing into the ion source.
from the high- and low-memory standards should symmetri-
6.1.1.4 Focus the instrument for resolution consistent with
cally bracket those of the sample to be corrected. Working
−10
precision requirements. A high-current ion beam of 5×10
standards approximately 5% apart (having a ratio of ratios of
−9
to 1×10 amps is necessary, with a signal-to-noise ratio
1.05) are suitable for most applications.
greater than 3000 in the low-current amplifier system.
8.1.2 A reasonable limit for the relative e between the
6.1.1.5 Adual collector must be used, so that ions from one
unknown sample and the working standard to which it is
isotope are passed through a resolving slit and focused on a
compared is 2.5%. A series of working standards prepared at
low-current collector, and ions from all other isotopes are
5% intervals and used for sample comparisons thus enables
focused on a high-current collector. The preferred method of
this 2.5% limit.
maintaining the low-current ion beam within the collector slit
8.1.3 Prepare a working standard, and standardize against
isbyanautomaticbeampositionercircuit.Aresolvingslitwith
an oxide blend of CRM standards that is within 0.02% of the
adjustable width features enhances the measurement of all
value of the working standard.
isotopes but is not mandatory for isotopic measurements.
8.2 Sample Preparation:
6.1.1.6 The amplified high- and low-current signals are fed
8.2.1 Attach tubes containing the appropriate working
into a multimeter or other device capable of ratioing high- and
standard,S,andthesample,X,tothespectrometerinletsystem,
low-current signals. If a multimeter is used, the multimeter
and prepare the materials for introduction into the ion source,
must have a minimum of 5.5 digits of resolution, a means of
as follows:
ratioing the high- and low-current signals, and interactive
communication capability with the controller. 8.2.1.1 If adequate sample and working standard are
6.1.1.7 The memory effect of the spectrometer must be available, open all valves between the sample and working
consistent with the precision required since a high memory standard containers and the pumping system, except the valves
level is usually more variable than a low one. Memory values on the sample and working standard containers. If the amount
of 2 to 3% are typical, but up to 10% memory can be of sample or working standard is limited, proceed to 8.2.2.
C1344−97 (2013)
8.2.1.2 Open the valve on the sample container, and then into the ion source, cond
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.