ASTM B690-02(2013)

Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Seamless Pipe and Tube

ABSTRACT
This specification covers iron-nickel-chromium-molybdenum alloys (UNS N08366 and UNS N08367) cold-finished annealed of hot-finished annealed seamless pipe and tube intended for use in special corrosive service and for heat-resisting applications. Pipe and tube shall be supplied in the solution heat treated and descaled condition. When bright annealing is used, descaling is not necessary. The tensile strength, yield strength, and elongation shall conform to the specified values. The pipe and tube shall be subject to a hydrostatic test.
SCOPE
1.1 This specification covers iron-nickel-chromium-molybdenum alloys (UNS N08366 and UNS N08367)* cold-finished annealed or hot-finished annealed seamless pipe and tube intended for use in special corrosive service and for heat-resisting applications.  
1.2 Pipe and tube shall be supplied in the solution heat treated and descaled condition. When bright annealing is used, descaling is not necessary.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Jan-2013
• ICS: 23.040.10 - Iron and steel pipes
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B690-02(2007) - Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Seamless Pipe and Tube
• Effective Date: 01-Feb-2013
• Referred By: ASTM B366/B366M-23 - Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• Effective Date: 01-Feb-2013
• Referred By: ASTM B924-02(2022) - Standard Specification for Seamless and Welded Nickel Alloy Condenser and Heat Exchanger Tubes With Integral Fins
• Effective Date: 01-Feb-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B690 −02 (Reapproved 2013)
Standard Specification for
Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and
1
UNS N08367) Seamless Pipe and Tube
This standard is issued under the fixed designation B690; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E8Test Methods for Tension Testing of Metallic Materials
E29Practice for Using Significant Digits in Test Data to
1.1 This specification covers iron-nickel-chromium-
Determine Conformance with Specifications
molybdenum alloys (UNS N08366 and UNS N08367)* cold-
E1473Test Methods for Chemical Analysis of Nickel,
finished annealed or hot-finished annealed seamless pipe and
Cobalt, and High-Temperature Alloys
tube intended for use in special corrosive service and for
heat-resisting applications.
3. Terminology
1.2 Pipe and tube shall be supplied in the solution heat
3.1 Definitions of Terms Specific to This Standard:
treated and descaled condition.When bright annealing is used,
3.1.1 average diameter, n—average of the maximum and
descaling is not necessary.
minimum outside diameters, or the maximum and minimum
1.3 The values stated in inch-pound units are to be regarded insidediameters,asdeterminedatanycrosssectionofthetube.
as standard. The values given in parentheses are mathematical
3.1.2 pipe, n—seamless tube conforming to the particular
conversions to SI units that are provided for information only
dimensions commercially known as standard pipe (Appendix
and are not considered standard.
X1).
1.4 The following safety hazards caveat pertains only to the
3.1.3 tube, n—hollow product of round or any other cross
test method portion, Section 12, of this specification. This
section having a continuous periphery.
standard does not purport to address all of the safety concerns,
4. Ordering Information
if any, associated with its use. It is the responsibility of the user
of this standard to become familiar with all hazards including
4.1 It is the responsibility of the purchaser to specify all
those identified in the appropriate Material Safety Data Sheet
requirements that are necessary for material ordered under this
(MSDS) for this product/material as provided by the
specification. Examples of such requirements include, but are
manufacturer, to establish appropriate safety and health
not limited to, the following:
practices, and determine the applicability of regulatory limi-
4.1.1 Quantity (feet, metres, or number of lengths),
tations prior to use.
4.1.2 Form (seamless tube or pipe),
4.1.3 Name of material or UNS number,
2. Referenced Documents
4.1.4 Finish,
2
2.1 ASTM Standards:
4.1.5 Dimensions:
A450/A450MSpecification for General Requirements for
4.1.5.1 Tube—Outside diameter, minimum wall thickness,
Carbon and Low Alloy Steel Tubes
4.1.5.2 Pipe—Standard pipe size and schedule (Appendix
B880Specification for General Requirements for Chemical
X1),
Check Analysis Limits for Nickel, Nickel Alloys and
4.1.5.3 Length—Specified or random,
Cobalt Alloys
4.1.6 Certification, if required (Section 15),
4.1.7 Purchaser’s inspection, if required, (Section 13),
1
This specification is under the jurisdiction of ASTM Committee B02 on
4.1.8 ASTM designation and year of issue, and
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
4.1.9 Samples for product analysis, if required.
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved Feb. 1, 2013. Published February 2013. Originally
5. Chemical Composition
approved in 1981. Last previous edition approved in 2007 as B690–02 (2007).
DOI: 10.1520/B0690-02R13.
5.1 The material shall conform to the composition limits
*New designation established in accordance withASTM E527 and SAE S1086,
specified in Table 1.
Practice for Numbering Metals and Alloys (UNS).
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.2 If a product (check) analysis is made by the purchaser,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
the material shall conform to the permissible variations for
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. product (check) analysis in Specification B880.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B690−02 (2013)
TABLE 1 Chemical Requirements TABLE 4 Permissible Variations in Outside Diameter, Pipe
Composition Limits, % Permissible Variations in Outside Diameter
Element
N08366 N08367 Nominal Pipe Size in. (mm) Plus Minus
Carbon 0.035 max 0.0
...