iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D520-00(2011)

(Specification)

Standard Specification for Zinc Dust Pigment

Standard Specification for Zinc Dust Pigment

ABSTRACT
This specification covers three types of zinc dust, for use as a pigment in paints. The pigments shall consist substantially of metallic zinc and shall conform to the requirements for composition prescribed. The total and metallic zinc shall be shall be tested to meet the requirements prescribed. Lead, cadmium, and iron shall be tested to meet the requirements prescribed. Oily or fatty matter, or both shall, and the coarse particle shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers three types of zinc dust, for use as a pigment in paints.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

General Information

Status
Historical
Publication Date
31-May-2011
ICS
87.060.10 - Pigments and extenders
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.31 - Pigment Specifications
Current Stage
Ref Project

Relations

Replaces
ASTM D520-00(2005) - Standard Specification for Zinc Dust Pigment
Effective Date
01-Jun-2011
Replaced By
ASTM D520-00(2019) - Standard Specification for Zinc Dust Pigment
Effective Date
01-May-2019

Buy Standard

ASTM D520-00(2011) - Standard Specification for Zinc Dust PigmentASTM D520-00(2011) - Standard Specification for Zinc Dust Pigment
PreviousNext
Technical specification
ASTM D520-00(2011) - Standard Specification for Zinc Dust Pigment
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D520 −00(Reapproved 2011)
Standard Specification for
Zinc Dust Pigment
This standard is issued under the fixed designation D520; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 3.2 In such physical properties as are specified by the
purchaser, the pigment shall satisfactorily match a reference
1.1 This specification covers three types of zinc dust, for use
sample mutually agreed upon between the purchaser and the
as a pigment in paints.
seller.
1.2 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are for information
4. Sampling
only.
4.1 Two samples shall be taken at random from different
packages from each lot, batch, day’s pack, or other unit of
2. Referenced Documents
production in a shipment. When no markings distinguishing
2.1 ASTM Standards:
between units of production appear, samples shall be taken
B214 Test Method for Sieve Analysis of Metal Powders
from different packages in the ratio of two samples for each
D185 Test Methods for Coarse Particles in Pigments
5000 kg (10 000 lb), except that for shipments of less than
D521 Test Methods for Chemical Analysis of Zinc Dust
5000 kg, two samples shall be taken. At the option of the
(Metallic Zinc Powder)
purchaser, the samples may be tested separately or after
E40 Method for Chemical Analysis of Slab Zinc (Spelter)
blending in equal quantities the samples from the same
(Withdrawn 1993)
production unit to form a composite sample.
3. Composition and Properties
5. Test Methods
3.1 The pigments shall consist substantially of metallic zinc
5.1 Tests shall be conducted in accordance with the follow-
and shall conform to the requirements for composition pre-
ing ASTM test methods. Test procedures not covered by these
scribed in Table 1.
ASTM test methods shall be mutually agreed upon between the
purchaser and the seller.
This specification is under the jurisdiction of ASTM Committee D01 on Paint
5.1.1 Total and Metallic Zinc—Test Methods D521.
and Related Coatings, Materials, andApplications and is the direct responsibility of
5.1.2 Lead, Cadmium, and Iron—Sections 8, 18.2, and 22,
Subcommittee D01.31 on Pigment Specifications.
Current edition approved June 1, 2011. Published June 2011. Originally
respectively, of Test Methods E40.
approved in 1939. Last previous edition approved in 2005 as D520 – 00 (2005).
5.1.3 Oily or Fatty Matter, or Both—Test Methods D521.
DOI: 10.1520/D0520-00R11.
5.1.4 CoarseParticles—Te
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2745-00(2023)(Test Method)
Standard Test Method for Relative Tinting Strength of White Pigments by Reflectance Measurements

SIGNIFICANCE AND USE
4.1 Tinting strength is one of the most important properties of a white pigment. This test method provides a means of testing this property for quality control.  
4.2 This test method is a referee method, and the vehicle for preparing the dispersion and the black for tinting are suggested, but others may be used provided both the purchaser and the seller agree to the changes.  
4.3 The results obtained with a muller do not necessarily agree with industrial situations where different dispersing conditions exist. However, dispersing with a muller is a fast, relatively inexpensive way of testing tinting strength for routine quality control.
SCOPE
1.1 This test method describes the procedure for determining the relative tinting strength of white pigments by reflectance measurements of black tints.  
1.2 This test method is applicable only for comparing the test pigment with a reference standard of the same type and grade.  
Note 1: Test Method D332 describes a procedure for visual assessment of blue-tinted samples.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6131-17(2023)(Test Method)
Standard Test Method for Evaluating the Relative Tint Undertone of Titanium Dioxide Pigments

SIGNIFICANCE AND USE
5.1 This test method allows the user to make a determination of the blueness or yellowness of the tint undertone of titanium dioxide pigments, versus a reference pigment agreed upon by the parties to the test. This is an important measure of tone, since it gives both a measure of effective particle size, and quick approximation of the blue/yellow undertone that can be expected when a coating containing the titanium dioxide is tinted.  
5.2 Such matters as the vehicle for preparing the dispersions and the mechanical method of preparing the dispersion are left to the user. However, variation in these practices will lead to increased variance in the results, so users ought to fix these parameters, in-so-far as is possible, within any one laboratory. This will lead to reduced uncertainty of the results within that laboratory, and it is seldom that interlaboratory comparisons of this test result is needed.  
5.3 Each user must decide whether the loss of accuracy in his measurements due to variation of these parameters is negligibly small for the purpose for which the data are obtained.
SCOPE
1.1 This test method is intended to be used to determine the tint undertone (blue or yellow) of titanium dioxide pigments. This relates to the effective particle size of the pigment  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6580-17(2023)(Test Method)
Standard Test Method for The Determination of Metallic Zinc Content in Both Zinc Dust Pigment and in Cured Films of Zinc-Rich Coatings

SIGNIFICANCE AND USE
4.1 This test method is useful for determining the amount of metallic zinc in zinc dust pigment, and also in dried films of both inorganic and organic zinc-rich coatings. Test Methods D521 is an appropriate method for analyzing zinc dust, but has shortcomings when applied to samples of cured coatings.
SCOPE
1.1 This test method covers the determination by differential scanning calorimetry of the metallic zinc content of both zinc-dust pigment, and of dried films of zinc-rich coatings. This test method is applicable to both inorganic and organic zinc-rich coatings.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D280-01(2023)(Test Method)
Standard Test Methods for Hygroscopic Moisture (and Other Matter Volatile Under the Test Conditions) in Pigments

ABSTRACT
These test methods establish the standard procedures for determining the hygroscopic moisture (and other matter volatile under the test conditions) in pigments. Method A shall be performed on pigments that do not decompose at a specified temperature. This method shall require the use of a wide-mouth cylindrical glass weighing bottle, an oven, and an analytical balance. Method B, on the other hand, shall be used for pigments that decompose at the same specified temperature. This method shall also need a wide-mouth cylindrical glass weighing bottle, an open-tube manometer, a glass desiccator, an oil vacuum pump, and an analytical balance.
SCOPE
1.1 These test methods cover procedures for determining hygroscopic moisture (and other matter volatile under the test conditions) in pigments.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D85-05(2023)(Specification)
Standard Specification for Ochre Pigment

ABSTRACT
This specification covers ferrous earthy pigment included under the general term “ochre.” The pigment shall be a hydrated oxide of iron permeating a siliceous base and shall be free from added impurities and added coloring matter. The following test methods shall be conducted: chemical analysis of dry pigment; coarse particles; mass color and tinting strength; volatile matter; and moisture. The results of these test methods should conform to the pigment requirements.
SCOPE
1.1 This specification covers ferrous earthy pigment included under the general term “ochre.” The pigment may be purchased in the dry form.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D34-08(2023)(Guide)
Standard Guide for Chemical Analysis of White Pigments

SIGNIFICANCE AND USE
3.1 This compilation of available ASTM methods for the analysis of white pigment serves as a guide to chemists.
SCOPE
1.1 This guide covers procedures for the chemical analysis of white pigments.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    1 page
    English language
    sale 15% off
ASTM
ASTM D185-07(2023)(Test Method)
Standard Test Methods for Coarse Particles in Pigments

SIGNIFICANCE AND USE
3.1 In production of paints, smoothness of the paint film is of paramount importance. Agglomerates or coarse particles larger than 45 μm are difficult to disperse and may prevent obtaining a smooth film. These test methods are a valuable quality control test for grading raw materials.
SCOPE
1.1 These test methods cover the determination of the amount of coarse particles in dry pigments.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D210-05(2023)(Specification)
Standard Specification for Bone Black Pigment

ABSTRACT
This specification covers bone black, ivory black, or drop black pigment. The pigment may be in dry form or in aqueous dispersion. Dry pigment shall be made by the calcinations of bones, unmixed with any other substance. Dry pigment shall compose of ash, ash insoluble in acids, and coarse particles. Pigment in aqueous dispersion shall be made by grinding the pigment with water, dispersing agent, biocide, fungicide, pH stabilizer, and defoamer. ASTM test methods shall be conducted for coarse particles, pigment and linseed oil in paste in oil, and mass color and tinting strength.
SCOPE
1.1 This specification covers the pigment commercially known as bone black, ivory black, or drop black. The pigment may be purchased in the dry form or as an aqueous dispersion.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D209-81(2023)(Specification)
Standard Specification for Lampblack Pigment

ABSTRACT
This specification covers the pigment commercially known as lampblack, which may be purchased in the dry form or as a paste in oil. The dry pigment shall be made by burning oils or tars. It shall conform to chemical compositions of ash, acetone extract, moisture and other volatile matter, and coarse particles. The paste in oil, on the other hand, shall be made by thoroughly grinding the specified pigment with linseed oil. It shall conform to chemical compositions of pigment, linseed oil, moisture and other volatile matter, and coarse particles and skins. Both forms of the pigment shall also be sampled, and tested appropriately for mass color and character, and tinting strength.
SCOPE
1.1 This specification covers the pigment commercially known as lampblack. The pigment may be purchased in the dry form or as a paste in oil.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D50-90(2023)(Test Method)
Standard Test Methods for Chemical Analysis of Yellow, Orange, Red, and Brown Pigments Containing Iron and Manganese

SIGNIFICANCE AND USE
3.1 These test methods compile in one place, recommended procedures for analyzing inorganic colored pigments. These pigments are used extensively in paints, and for this reason their compositions are important to the formulators and user.
SCOPE
1.1 These test methods cover procedures for the chemical analysis of yellow, orange, red, and brown pigments containing iron and manganese. The test methods apply specifically to the following pigments: synthetic hydrated yellow iron oxide, yellow ocher, red and brown iron oxides, raw and burnt umber, raw and burnt sienna, and venetian red.  
1.2 The analytical procedures appear in the following order:    
ASTM  
Method  
Refer-  
Dry Pigments
Sections  
ences  
Moisture and Other Volatile Matter  
6  
D280  
Loss on Ignition  
7  
Coarse Particles  
8  
D185  
Matter Soluble in Water  
9  
D1208  
Organic Coloring Matter  
10  
Iron Oxide  
11 and 12  
Calcium Compounds (Reported as CaO)  
13 and 14  
Sulfates Soluble in Hydrochloric Acid  
15 and 16  
Lead Chromate (in Ochers)  
17  
Calcium Carbonate (in Venetian Red)  
18  
C25  
Manganese (in Siennas and Umbers)  
19 and 20  
Pigment Pastes in Oil  
Pigment Content  
21  
D1208  
Moisture and Other Volatile Matter  
22  
D1208  
Nonvolatile Matter in Vehicle  
23  
Moisture by Distillation  
24  
D1208  
Coarse Particles and Skins  
25  
D185  
Consistency (Stormer)  
26  
D562  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to us.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off