ASTM F1488-09e1

Standard Specification for Coextruded Composite Pipe

ABSTRACT
This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite pipe conforming to the requirements prescribed are used for different applications: IPS Schedule 40 Series-coextruded composite pipe is used for above or below ground installation for communication conduit, electrical conduit, drain, waste, and vent pipe, and plastic underdrain systems for highway, airport, and similar drainage, where a Schedule 40 IPS is required; IPS-DR-PS Series-coextruded composite pipe is used for above or below ground installation for communication conduit, electrical conduit, and drain, waste, and vent pipe; and Sewer and Drain DR-PS Series-coextruded composite pipe is used for gravity flow sewer and drain pipe, and plastic underdrain systems for highway, airport, and similar drainage. The pipe stiffness, impact resistance, and bond strength shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die.
1.1.1 Materials listed in the material section are permitted to be used in any layer of the coextruded composite pipe. When coextruded composite pipe is produced with three layers, the middle layer is permitted to be solid or thermally foamed.
1.1.2 The function of this specification is to provide standardization of product, to produce technical data, and to serve as a purchasing guide.
1.2 Compounds that do not meet the requirements of the material section are excluded.
1.3 The coextruded composite pipe is permitted to be perforated in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.4 The coextruded composite pipe is permitted to be belled for joining by solvent cementing or belled for joining by an elastomeric seal (gaskets), in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.5 Recommendations for storage, joining, installation, and rationale are listed in Appendixes X1, X2, X3, and X4, respectively.
1.6 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. A companion standard written in SI units is under development.  
1.7 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

General Information

• Status: Historical
• Publication Date: 31-Jul-2009
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.11 - Composite

Relations

• Replaces: ASTM F1488-09 - Standard Specification for Coextruded Composite Pipe
• Effective Date: 01-Aug-2009
• Replaced By: ASTM F1488-14 - Standard Specification for Coextruded Composite Pipe
• Effective Date: 01-Dec-2014
• Referred By: ASTM F412-23 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Aug-2009

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:F1488 −09 AnAmerican National Standard
Standard Specification for
1
Coextruded Composite Pipe
This standard is issued under the fixed designation F1488; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—2.2 was editorially corrected in December 2010.
1. Scope responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
1.1 This specification covers coextruded composite pipe,
bility of regulatory limitations prior to use.
produced by a coextrusion die system, in which the concentric
layers are formed and combined before exiting the die.
NOTE 1—Related specifications are as follows: D2661, D2665, D2729,
D2750, D2751, D2949, D3034, F512, F628, F758, F789, and F891.
1.1.1 Materialslistedinthematerialsectionarepermittedto
be used in any layer of the coextruded composite pipe. When
2. Referenced Documents
coextruded composite pipe is produced with three layers, the
middle layer is permitted to be solid or thermally foamed.
2.1 The following standards contain provisions which,
1.1.2 The function of this specification is to provide stan-
thoughreferencedinthisspecification,constituteprovisionsof
dardization of product, to produce technical data, and to serve
this specification. All standards are subject to revision and
as a purchasing guide.
parties using this specification shall reference the most recent
edition of the standards listed as follows.
1.2 Compounds that do not meet the requirements of the
2
material section are excluded.
2.2 ASTM Standards:
D618Practice for Conditioning Plastics for Testing
1.3 The coextruded composite pipe is permitted to be
D696TestMethodforCoefficientofLinearThermalExpan-
perforated in accordance with any specified standard or by
sion of Plastics Between −30°C and 30°C with a Vitreous
agreement between the purchaser and the supplier.
Silica Dilatometer
1.4 Thecoextrudedcompositepipeispermittedtobebelled
D883Terminology Relating to Plastics
for joining by solvent cementing or belled for joining by an
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
elastomeric seal (gaskets), in accordance with any specified
tics
standard or by agreement between the purchaser and the 3
D1898Practice for Sampling of Plastics (Withdrawn 1998)
supplier.
D1972Practice for Generic Marking of Plastic Products
3
1.5 Recommendations for storage, joining, installation, and (Withdrawn 2014)
rationale are listed in Appendixes X1, X2, X3, and X4,
D2122Test Method for Determining Dimensions of Ther-
respectively. moplastic Pipe and Fittings
D2235Specification for Solvent Cement for Acrylonitrile-
1.6 Thevaluesstatedininch-poundunitsaretoberegarded
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
asstandard.Nootherunitsofmeasurementareincludedinthis
D2321PracticeforUndergroundInstallationofThermoplas-
standard. A companion standard written in SI units is under
tic Pipe for Sewers and Other Gravity-Flow Applications
development.
D2412Test Method for Determination of External Loading
1.7 Thetextofthisspecificationreferencesnotes,footnotes,
Characteristics of Plastic Pipe by Parallel-Plate Loading
and appendixes which provide explanatory material. These
D2444Test Method for Determination of the Impact Resis-
notesandfootnotes(excludingthoseintablesandfigures)shall
tance of Thermoplastic Pipe and Fittings by Means of a
not be considered as requirements of this specification.
Tup (Falling Weight)
1.8 This standard does not purport to address all of the
D2564Specification for Solvent Cements for Poly(Vinyl
safety concerns, if any, associated with its use. It is the
1 2
This specification is under the jurisdiction ofASTM Committee F17 on Plastic For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Piping Systems and is the direct responsibility of Subcommittee F17.11 on contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Composite. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Aug. 1, 2009. Published August 2009. Originally the ASTM website.
3
approved in 1994. Last previous edition approved in 2003 as F1488–03. DOI: The last approved version of this historical standard is referenced on
10.1520/F1488-09E01. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
F1488−09
Chloride) (PVC) Plastic Piping Systems F891Specification for Coextruded Poly(Vinyl Chloride)
D2661 Specification for Acrylonitrile-Butadiene-
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
´1
Designation:F1488–09 Designation: F1488 – 09
Standard Specification for
1
Coextruded Composite Pipe
This standard is issued under the fixed designation F1488; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—2.2 was editorially corrected in December 2010.
1. Scope
1.1 This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers
are formed and combined before exiting the die.
1.1.1 Materials listed in the material section are permitted to be used in any layer of the coextruded composite pipe. When
coextruded composite pipe is produced with three layers, the middle layer is permitted to be solid or thermally foamed.
1.1.2 The function of this specification is to provide standardization of product, to produce technical data, and to serve as a
purchasing guide.
1.2 Compounds that do not meet the requirements of the material section are excluded.
1.3 The coextruded composite pipe is permitted to be perforated in accordance with any specified standard or by agreement
between the purchaser and the supplier.
1.4 The coextruded composite pipe is permitted to be belled for joining by solvent cementing or belled for joining by an
elastomeric seal (gaskets), in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.5 Recommendationsforstorage,joining,installation,andrationalearelistedinAppendixesX1,X2,X3,andX4,respectively.
1.6 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard. A companion standard written in SI units is under development.
1.7 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
NOTE 1—Related specifications are as follows: D2661, D2665, D2729, D2750, D2751, D2949, D3034, F512, F628, F758, F789, and F891.
2. Referenced Documents
2.1 The following standards contain provisions which, though referenced in this specification, constitute provisions of this
specification.All standards are subject to revision and parties using this specification shall reference the most recent edition of the
standards listed as follows.
2
2.2 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between 30C and 30C with a Vitreous Silica
Dilatometer
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
3
D1898 Standard Practice for Sampling of Plastics
D1972 Practice for Generic Marking of Plastic Products
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.11 on Composite.
Current edition approved Aug. 1, 2009. Published August 2009. Originally approved in 1994. Last previous edition approved in 2003 as F1488–03. DOI:
10.1520/F1488-09.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,[e-mail] Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
´1
F1488 – 09
D2444 TestMethodforDeterminationoftheImpactResistanceofThermoplasticPipeandFittingsbyMeansofaTup(Falli
...