ASTM D2680-01(2009)

Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping

ABSTRACT
This specification covers acrylonitrile-butadiene-styrene (ABS) and poly(vinyl chloride) (PVC) thermoplastic composite pipe, fittings, and a joining system for use in gravity flow, nonpressure sanitary sewer, and storm drain installations. ABS or PVC composite pipes shall consist of two concentric thermoplastic tubes integrally braced across the annulus and the resultant annular space shall be filled to provide continuous support between the inner and outer tubes. Referee and quality control tests shall be conducted in the standard laboratory atmosphere under the specified temperature and humidity conditions. The pipe shall be tested for performance requirements such as stiffness, deflection without rupture, acid conditioning, joint (solvent cement and elastomeric seal joints) tightness, and extrusion quality.
SCOPE
1.1 This specification covers thermoplastic composite pipe, fittings and a joining system for use in gravity flow, nonpressure sanitary sewer, and storm drain installations. The pipe and fittings are made of ABS or PVC plastic material. Recommended installation practices are referenced in Appendix X1.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in 7.2.4.

General Information

• Status: Historical
• Publication Date: 28-Feb-2009
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.62 - Sewer

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2680 −01(Reapproved 2009) An American National Standard
Standard Specification for
Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl
1
Chloride) (PVC) Composite Sewer Piping
This standard is issued under the fixed designation D2680; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D2235Specification for Solvent Cement for Acrylonitrile-
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
1.1 This specification covers thermoplastic composite pipe,
D2321PracticeforUndergroundInstallationofThermoplas-
fittings and a joining system for use in gravity flow, nonpres-
tic Pipe for Sewers and Other Gravity-Flow Applications
suresanitarysewer,andstormdraininstallations.Thepipeand
D2412Test Method for Determination of External Loading
fittings are made of ABS or PVC plastic material. Recom-
Characteristics of Plastic Pipe by Parallel-Plate Loading
mended installation practices are referenced in Appendix X1.
D2564Specification for Solvent Cements for Poly(Vinyl
1.2 The values stated in inch-pound units are to be regarded
Chloride) (PVC) Plastic Piping Systems
as standard. The values given in parentheses are mathematical
D3138Specification for Solvent Cements for Transition
conversions to SI units that are provided for information only
Joints Between Acrylonitrile-Butadiene-Styrene (ABS)
and are not considered standard.
and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping
1.3 The following safety hazards caveat pertains only to the Components
test method portion, Section 10, of this specification: This
D3212Specification for Joints for Drain and Sewer Plastic
standard does not purport to address all of the safety problems, Pipes Using Flexible Elastomeric Seals
if any, associated with its use. It is the responsibility of the user
D3965ClassificationSystemandBasisforSpecificationsfor
of this standard to establish appropriate safety and health Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials
practices and determine the applicability of regulatory limita-
for Pipe and Fittings
tions prior to use.Specific precautionary information is given D4396Specification for Rigid Poly(Vinyl Chloride) (PVC)
in 7.2.4.
and Chlorinated Poly(Vinyl Chloride) (CPVC) Com-
pounds for Plastic Pipe and Fittings Used in Nonpressure
2. Referenced Documents
Applications
2
F402 Practice for Safe Handling of Solvent Cements,
2.1 ASTM Standards:
Primers, and Cleaners Used for Joining Thermoplastic
D618Practice for Conditioning Plastics for Testing
Pipe and Fittings
D1084Test Methods for Viscosity of Adhesives
F412Terminology Relating to Plastic Piping Systems
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
F477Specification for Elastomeric Seals (Gaskets) for Join-
tics
ing Plastic Pipe
D1784Specification for Rigid Poly(Vinyl Chloride) (PVC)
F913Specification for Thermoplastic Elastomeric Seals
Compounds and Chlorinated Poly(Vinyl Chloride)
(Gaskets) for Joining Plastic Pipe
(CPVC) Compounds
2.2 Federal Standard:
D2122Test Method for Determining Dimensions of Ther-
3
Fed. Std. No. 123Marking for Shipment (Civil Agencies)
moplastic Pipe and Fittings
2.3 Military Standard:
D2152Test Method for Adequacy of Fusion of Extruded
3
MIL-STD-129 Marking for Shipment and Storage
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
Acetone Immersion
3. Terminology
3.1 Definitions:
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
3.1.1 General—Definitions are in accordance with Termi-
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
nology F412 and abbreviations are in accordance with Termi-
Current edition approved March 1, 2009. Published March 2009. Originally
published as D2680–68T. Last previous edition D2680–01. DOI: 10.1520/ nologyD1600,unlessotherwisespecified.Theabbreviationfor
D2680-01R09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2680−01 (2009)
acrylonitrile-butadiene-styreneisABSandtheabbreviationfor fittings production may be used by the same manufacturer
poly(vinyl chloride) is PVC. provided that the pipe and fittings produced meet all the
require
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D 2680–95a Designation: D 2680 – 01 (Reapproved 2009)
Standard Specification for
Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl
1
Chloride) (PVC) Composite Sewer Piping
This standard is issued under the fixed designation D 2680; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers thermoplastic composite pipe, fittings and a joining system for use in gravity flow, nonpressure
sanitary sewer, and storm drain installations. The pipe and fittings are made of ABS or PVC plastic material. Recommended
installation practices are referenced in Appendix XI.X1.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 Thefollowingsafetyhazardscaveatpertainsonlytothetestmethodportion,Section10,ofthisspecification: This standard
does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Specific precautionary information is given in Note 67.2.4.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics and Electrical Insulating Materials for Testing Practice for Conditioning Plastics for
Testing
D1084 Test Methods for Viscosity of Adhesives
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2152 Test Method for DegreeAdequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
Acetone Immersion
D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity–-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D3138 Specification for Solvent Cements for Transition Joints BetweenAcrylonitrile-Butadiene-Styrene (ABS) and Poly(Vi-
nyl Chloride) (PVC) Non-Pressure Piping Components
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3965 Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) CompoundsMaterials for Pipe and Fittings
4
D4396 Specification for Rigid Poly(Vinyl Chloride)(PVC) and Related Plastic Compounds for Nonpressure Piping Products
Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic
Pipe and Fittings Used in Nonpressure Applications
F402 Practice for Safe Handling of Solvent Cements, Primers, and PrimersCleaners Used for Joining Thermoplastic Pipe and
Fittings
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
1
This specification is under the jurisdiction ofASTM Committee F-17F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
Current edition approved Sept. 10, 1995.March 1, 2009. Published November 1995.March 2009. Originally published as D2680–68T. Last previous edition
D2680–95.D2680–01.
2
Annual Book of ASTM Standards, Vol 08.01.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,[e-mail] Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 2680 – 01 (2009)
F913 Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agen
...