ASTM A358/A358M-14
(Specification)Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications
Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications
ABSTRACT
This specification covers electric-fusion-welded austenitic chromium-nickel stainless steel pipe suitable for corrosive or high-temperature service, or both, or for general applications. The pipes shall be sorted into five different classes. Class 1 pipes shall be double welded by processes employing filler metal in all passes and shall be completely radiographed. Pipes of Class 2 shall be double welded by processes employing filler metal in all passes with no radiography. Both Class 3 and Class 4 pipes shall be single welded except that the weld pass of the latter exposed to the inside pipe surface may be without the addition of filler metal. Pipes of Class 5 shall be double welded by processes employing filler metal and shall be spot radiographed. Weld defects shall be repaired by removal to sound metal and rewelding. Subsequent heat treatment shall be as required on the original welds. The finished pipes shall be subjected to transverse tension test, transverse guided-bend weld test, and hydrostatic test.
SCOPE
1.1 This specification2 covers electric-fusion-welded austenitic chromium-nickel stainless steel pipe suitable for corrosive or high-temperature service, or both, or for general applications. Note 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”
1.2 This specification covers the grades of alloy and stainless steel listed in Table 1. The selection of the proper grade and requirements for heat treatment shall be at the discretion of the purchaser, dependent on the service conditions to be encountered.
1.3 Five classes of pipe are covered as follows:
1.3.1 Class 1—Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed.
1.3.2 Class 2—Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required.
1.3.3 Class 3—Pipe shall be single welded by processes employing filler metal in all passes and shall be completely radiographed.
1.3.4 Class 4—Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal (see 6.2.2.1 and 6.2.2.2).
1.3.5 Class 5—Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed.
1.4 Supplementary requirements covering provisions ranging from additional testing to formalized procedures for manufacturing practice are provided. Supplementary Requirements S1 through S6 are included as options to be specified when desired.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A358/A358M −14 Usedin USDOE-NE Standards
Standard Specification for
Electric-Fusion-Welded Austenitic Chromium-Nickel
Stainless Steel Pipe for High-Temperature Service and
1
General Applications
This standard is issued under the fixed designationA358/A358M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* manufacturing practice are provided. Supplementary Require-
ments S1 through S6 are included as options to be specified
2
1.1 This specification covers electric-fusion-welded auste-
when desired.
niticchromium-nickelstainlesssteelpipesuitableforcorrosive
1.5 The values stated in either inch-pound units or SI units
or high-temperature service, or both, or for general applica-
tions. are to be regarded separately as standard. Within the text, the
SI units are shown in brackets. The values stated in each
NOTE 1—The dimensionless designator NPS (nominal pipe size) has
system may not be exact equivalents; therefore, each system
been substituted in this standard for such traditional terms as “nominal
shall be used independently of the other. Combining values
diameter,” “size,” and “nominal size.”
from the two systems may result in nonconformance with the
1.2 This specification covers the grades of alloy and stain-
specification. The inch-pound units shall apply unless the “M”
less steel listed in Table 1. The selection of the proper grade
designation of this specification is specified in the order.
andrequirementsfor heat treatment shall be at the discretionof
the purchaser, dependent on the service conditions to be
2. Referenced Documents
encountered.
3
2.1 ASTM Standards:
1.3 Five classes of pipe are covered as follows:
A240/A240M Specification for Chromium and Chromium-
1.3.1 Class 1—Pipe shall be double welded by processes
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
employing filler metal in all passes and shall be completely
Vessels and for General Applications
radiographed.
A262 Practices for Detecting Susceptibility to Intergranular
1.3.2 Class 2—Pipe shall be double welded by processes
Attack in Austenitic Stainless Steels
employing filler metal in all passes. No radiography is re-
A480/A480M Specification for General Requirements for
quired.
Flat-Rolled Stainless and Heat-Resisting Steel Plate,
1.3.3 Class 3—Pipe shall be single welded by processes
Sheet, and Strip
employing filler metal in all passes and shall be completely
A941 TerminologyRelatingtoSteel,StainlessSteel,Related
radiographed.
Alloys, and Ferroalloys
1.3.4 Class 4—Same as Class 3 except that the weld pass
A999/A999M Specification for General Requirements for
exposed to the inside pipe surface may be made without the
Alloy and Stainless Steel Pipe
addition of filler metal (see 6.2.2.1 and 6.2.2.2).
E527 Practice for Numbering Metals and Alloys in the
1.3.5 Class 5—Pipe shall be double welded by processes
Unified Numbering System (UNS)
employing filler metal in all passes and shall be spot radio-
4
2.2 ASME Boiler and Pressure Vessel Code:
graphed.
Section II
1.4 Supplementary requirements covering provisions rang-
Section III
ing from additional testing to formalized procedures for
Section VIII
Section IX
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
3
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee For referenced ASTM standards, visit the ASTM website, www.astm.org, or
A01.10 on Stainless and Alloy Steel Tubular Products. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved March 1, 2014. Published March 2014. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1952. Last previous edition approved in 2012 as A358/A358M – 12. the ASTM website.
4
DOI: 10.1520/A0358_A0358M-14. Available from American Society of Mechanical Engineers (ASME), ASME
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
cations SA-358 in Section II of that Code. www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A358/A358M−14
2
TABLE 1 Plate and Filler Metal Specifications
A B
Filler Metal Classification and UNS Designation for Applicable AWS Specification
UNS ASTM Plate
Material,
Grade Desig- Specification No. A5.4/A5.4M A5.9/A5.9M A5.11/A5.11M A5.14/A5.14M A5.22/A5.22M A5.30/A5.
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A358/A358M − 12 A358/A358M − 14 Used in USDOE-NE Standards
Standard Specification for
Electric-Fusion-Welded Austenitic Chromium-Nickel
Stainless Steel Pipe for High-Temperature Service and
1
General Applications
This standard is issued under the fixed designation A358/A358M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
2
1.1 This specification covers electric-fusion-welded austenitic chromium-nickel stainless steel pipe suitable for corrosive or
high-temperature service, or both, or for general applications.
NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,”
“size,” and “nominal size.”
1.2 This specification covers the grades of alloy and stainless steel listed in Table 1. The selection of the proper grade and
requirements for heat treatment shall be at the discretion of the purchaser, dependent on the service conditions to be encountered.
1.3 Five classes of pipe are covered as follows:
1.3.1 Class 1—Pipe shall be double welded by processes employing filler metal in all passes and shall be completely
radiographed.
1.3.2 Class 2—Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required.
1.3.3 Class 3—Pipe shall be single welded by processes employing filler metal in all passes and shall be completely
radiographed.
1.3.4 Class 4—Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition
of filler metal (see 6.2.2.1 and 6.2.2.2).
1.3.5 Class 5—Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed.
1.4 Supplementary requirements covering provisions ranging from additional testing to formalized procedures for manufac-
turing practice are provided. Supplementary Requirements S1 through S6 are included as options to be specified when desired.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in nonconformance with the specification. The
inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
2. Referenced Documents
3
2.1 ASTM Standards:
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee A01.10
on Stainless and Alloy Steel Tubular Products.
Current edition approved Dec. 1, 2012March 1, 2014. Published January 2013March 2014. Originally approved in 1952. Last previous edition approved in 20082012 as
A358/A358M – 08a.A358/A358M – 12. DOI: 10.1520/A0358_A0358M-12.10.1520/A0358_A0358M-14.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifications SA-358 in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A358/A358M − 14
2
TABLE 1 Plate and Filler Metal Specifications
A B
Filler Metal Classification and UNS Designation for Applicable AWS Specification
UNS A
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.