ASTM D3965-11
(Specification)Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
ABSTRACT
This specification covers materials made from only virgin ABS polymers and blends of ABS polymers suitable for use in the extrusion of pipe and molding of fittings. ABS polymers and blends of ABS polymers shall be classified according to cell limits: Cell 0; Cell 1; Cell 2; Cell 3; Cell 4; and Cell 5. The ABS material shall be produced by polymerization of the monomers, acrylonitrile, butadiene, and styrene, or their closely related chemical derivatives, or from a blend of ABS polymers from those monomers. The blend of ABS polymers can be intimately mixed by melt compounding, or it can be a homogeneous physical mixture of discrete ABS polymers. Materials shall be measured using techniques in accordance with the following test methods: impact testing; deflection temperature under load; tensile stress at yield point; modulus of elasticity in tension; and specific gravity.
SCOPE
1.1 This classification system covers materials made from only virgin ABS polymers and blends of ABS polymers suitable for use in the extrusion of pipe and molding of fittings.
1.2 The requirements of this classification system are applicable only to the ABS polymers and blends of ABS polymers as classified and do not address the requirements of the finished pipe or fittings. The applicable ASTM standard specification for pipe or fittings shall be consulted for their requirements.
1.3 This classification system excludes ABS polymers and blends of ABS polymers made from reprocessed, regrind, reclaimed, or recycled materials. ABS rework, generated in-house by the original plastic manufacturer, may be used by that original manufacturer, provided the ABS product shipped meets the physical and mechanical properties required by its callout in Table 1.
1.4 This classification system and subsequent line callout (specification) provides a means for describing ABS materials used in the manufacture of pipe and fittings. It is not intended for the selection of materials. Material selection shall be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material other than those covered by this classification system, and the economics.
1.5 This classification system and subsequent line callout (specification) provides for the classification of ABS polymers and blends of ABS polymers into groups based on five properties: Izod impact strength at room temperature, Izod impact strength at low temperature, deflection temperature under load, tensile stress at yield point, and modulus of elasticity in tension. The properties included are those required to identify the ABS material by the cell classifications.
Note 1—Other requirements necessary to identify particular characteristics of ABS polymers and blends of ABS polymers will be added as test methods become available or the need is identified.
Note 2—Due to pipe and fitting standards requirements a separate standard is planned for recycled materials.
Note 3—This classification system and ISO 7245-1984 are not equivalent.
1.6 The values stated in SI units shall be the standard. The values given in parentheses are for information only.
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this classification system:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
TABLE 1 Physical Property Requirements for ABS Pipe and Fitting Materials
Note—The minimum property value for any material will determine the cell number although the maximum expected value may fall within the next higher cell. ASTM
Test Method...
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D3965 −11
StandardClassification System and Basis for Specifications for
Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for
1
Pipe and Fittings
This standard is issued under the fixed designation D3965; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
NOTE 1—Other requirements necessary to identify particular character-
1. Scope*
istics ofABS polymers and blends ofABS polymers will be added as test
1.1 This classification system covers materials made from
methods become available or the need is identified.
only virgin ABS polymers and blends of ABS polymers NOTE 2—Due to pipe and fitting standards requirements a separate
standard is planned for recycled materials.
suitable for use in the extrusion of pipe and molding of fittings.
NOTE 3—This classification system and ISO 7245-1984 are not equiva-
1.2 The requirements of this classification system are appli-
lent.
cable only to the ABS polymers and blends of ABS polymers
1.6 The values stated in SI units shall be the standard. The
asclassifiedanddonotaddresstherequirementsofthefinished
values given in parentheses are for information only.
pipe or fittings. The applicable ASTM standard specification
1.7 The following safety hazards caveat pertains only to the
for pipe or fittings shall be consulted for their requirements.
test methods portion, Section 13, of this classification system-
1.3 This classification system excludes ABS polymers and
:This standard does not purport to address all of the safety
blends of ABS polymers made from reprocessed, regrind,
concerns, if any, associated with its use. It is the responsibility
reclaimed, or recycled materials. ABS rework, generated in-
of the user of this standard to establish appropriate safety and
house by the original plastic manufacturer, may be used by that
health practices and determine the applicability of regulatory
original manufacturer, provided the ABS product shipped
limitations prior to use.
meets the physical and mechanical properties required by its
callout in Table 1.
2. Referenced Documents
2
1.4 This classification system and subsequent line callout
2.1 ASTM Standards:
(specification) provides a means for describing ABS materials
D256 Test Methods for Determining the Izod Pendulum
used in the manufacture of pipe and fittings. It is not intended
Impact Resistance of Plastics
for the selection of materials. Material selection shall be made
D618 Practice for Conditioning Plastics for Testing
by those having expertise in the plastics field after careful
D638 Test Method for Tensile Properties of Plastics
considerationofthedesignandtheperformancerequiredofthe
D648 Test Method for Deflection Temperature of Plastics
part, the environment to which it will be exposed, the fabrica-
Under Flexural Load in the Edgewise Position
tion process to be employed, the inherent properties of the
D792 Test Methods for Density and Specific Gravity (Rela-
material other than those covered by this classification system,
tive Density) of Plastics by Displacement
and the economics.
D883 Terminology Relating to Plastics
D1600 Terminology forAbbreviatedTerms Relating to Plas-
1.5 This classification system and subsequent line callout
tics
(specification) provides for the classification ofABS polymers
D3641 Practice for Injection Molding Test Specimens of
and blends of ABS polymers into groups based on five
Thermoplastic Molding and Extrusion Materials
properties: Izod impact strength at room temperature, Izod
D3892 Practice for Packaging/Packing of Plastics
impact strength at low temperature, deflection temperature
D4000 Classification System for Specifying Plastic Materi-
under load, tensile stress at yield point, and modulus of
als
elasticity in tension. The properties included are those required
D5947 Test Methods for Physical Dimensions of Solid
to identify the ABS material by the cell classifications.
Plastics Specimens
F412 Terminology Relating to Plastic Piping Systems
1
ThisclassificationsystemisunderthejurisdictionofASTMCommitteeD20on
Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic
2
Materials. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2011. Published October 2011. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1980. Last previous edition approved in 2005 as D3965 - 05. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D3965-11. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM Int
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3965–05
Standard Specification for Designation: D3965 – 11
Standard Classification System and Basis for Specifications for
Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for
1
Pipe and Fittings
This standard is issued under the fixed designation D3965; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification classification system covers materials made from only virginABS polymers and blends ofABS polymers
suitable for use in the extrusion of pipe and molding of fittings.
1.2 The requirements of this specification classification system are applicable only to the ABS polymers and blends of ABS
polymers as classified and do not address the requirements of the finished pipe or fittings. The applicable ASTM standard
specification for pipe or fittings shouldshall be consulted for their requirements.
1.3 This specificationclassification system excludes ABS polymers and blends of ABS polymers made from reprocessed,
regrind, reclaimed, or recycled materials. ABS rework, generated in-house by the original plastic manufacturer, may be used by
that original manufacturer, provided theABS product shipped meets the physical and mechanical properties required by its callout
in Table 1of this specification.
1.4This specification .
1.4 This classification system and subsequent line callout (specification) provides a means for describing ABS materials used
in the manufacture of pipe and fittings. It is not intended for the selection of materials. Material selection shouldshall be made by
those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the
environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material other than
those covered by this specification, classification system, and the economics.
1.5 This classification system and subsequent line callout (specification) provides for the classification of ABS polymers and
blends of ABS polymers into groups based on five properties: Izod impact strength at room temperature, Izod impact strength at
lowtemperature,deflectiontemperatureunderload,tensilestressatyieldpoint,andmodulusofelasticityintension.Theproperties
included in this specification are those required to identify the ABS material by the cell classifications.
NOTE 1—Other requirements necessary to identify particular characteristics of ABS polymers and blends of ABS polymers will be added as test
methods become available or the need is identified.
NOTE 2—Due to pipe and fitting standards requirements a separate standard is planned for recycled materials.
NOTE3—This specification and ISO 7245-1984 3—This classification system and ISO 7245-1984 are not equivalent.
1.6 The values stated in SI units shall be the standard. The values given in bracketsparentheses are for information only.
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification:, of this
classification system:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of
regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
1
This specification classification system is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.15 on
Thermoplastic Materials.
Current edition approved JulySept. 1, 2005.2011. Published July 2005.October 2011. Originally approved in 1980. Last previous edition approved in 20042005 as
D3965 - 045. DOI: 10.1520/D3965-05.10.1520/D3965-11.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
-----
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.