ASTM F412-09
(Terminology)Standard Terminology Relating to Plastic Piping Systems
Standard Terminology Relating to Plastic Piping Systems
SCOPE
1.1 This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are generally understood or adequately defined in other readily available sources are not included.
1.2 When a term is used in an ASTM document for which Committee F17 is responsible it is included only when judged, after review, by Subcommittee F17.91 to be a generally usable term.
1.3 Definitions that are identical to those published by other ASTM committees or other standards organizations are identified with the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPAC International Union of Pure and Applied Chemistry).
1.4 A definition is a single sentence with additional information included in notes.
1.5 Definitions are followed by the committee responsible for the standard(s) (for example, [F17.26]) and standard numbers(s) in which they are used (for example, F 714).
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation:F412–09
Standard Terminology Relating to
1
Plastic Piping Systems
ThisstandardisissuedunderthefixeddesignationF412;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D882 Test Method for Tensile Properties of Thin Plastic
Sheeting
1.1 This terminology is a compilation of definitions of
D883 Terminology Relating to Plastics
technical terms used in the plastic piping industry. Terms that
D907 Terminology of Adhesives
are generally understood or adequately defined in other readily
D1003 Test Method for Haze and Luminous Transmittance
available sources are not included.
of Transparent Plastics
1.2 When a term is used in an ASTM document for which
D1079 TerminologyRelatingtoRoofingandWaterproofing
Committee F17 is responsible it is included only when judged,
D1238 Test Method for Melt Flow Rates ofThermoplastics
after review, by Subcommittee F17.91 to be a generally usable
by Extrusion Plastometer
term.
D1488 Test Method for Amylaceous Matter in Adhesives
1.3 Definitionsthatareidenticaltothosepublishedbyother
D1505 Test Method for Density of Plastics by the Density-
ASTM committees or other standards organizations are iden-
Gradient Technique
tified with the committee number (for example, D20) or with
D1527 Specification for Acrylonitrile-Butadiene-Styrene
the abbreviation of the name of the organization (for example,
(ABS) Plastic Pipe, Schedules 40 and 80
IUPAC International Union of Pure and Applied Chemistry).
D1785 SpecificationforPoly(VinylChloride)(PVC)Plastic
1.4 A definition is a single sentence with additional infor-
Pipe, Schedules 40, 80, and 120
mation included in notes.
D2104 Specification for Polyethylene (PE) Plastic Pipe,
1.5 Definitions are followed by the committee responsible
Schedule 40
for the standard(s) (for example, [F17.26]) and standard
D2239 Specification for Polyethylene (PE) Plastic Pipe
numbers(s) in which they are used (for example, F714).
(SIDR-PR) Based on Controlled Inside Diameter
2. Referenced Documents D2241 Specification for Poly(Vinyl Chloride) (PVC)
2
Pressure-Rated Pipe (SDR Series)
2.1 ASTM Standards:
D2282 Specification for Acrylonitrile-Butadiene-Styrene
C114 Test Methods for Chemical Analysis of Hydraulic
3
(ABS) Plastic Pipe
Cement
D2444 Test Method for Determination of the Impact Resis-
D256 Test Methods for Determining the Izod Pendulum
tance of Thermoplastic Pipe and Fittings by Means of a
Impact Resistance of Plastics
Tup (Falling Weight)
D638 Test Method for Tensile Properties of Plastics
D2447 Specification for Polyethylene (PE) Plastic Pipe,
D648 Test Method for Deflection Temperature of Plastics
Schedules 40 and 80, Based on Outside Diameter
Under Flexural Load in the Edgewise Position
D2513 Specification for Thermoplastic Gas Pressure Pipe,
D747 Test Method forApparent Bending Modulus of Plas-
Tubing, and Fittings
tics by Means of a Cantilever Beam
D2661 Specification for Acrylonitrile-Butadiene-Styrene
D790 Test Methods for Flexural Properties of Unreinforced
(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe
andReinforcedPlasticsandElectricalInsulatingMaterials
and Fittings
3
D2666 Specification for Polybutylene (PB) Plastic Tubing
1
This terminology is under the jurisdiction ofASTM Committee F17 on Plastic
D2680 Specification for Acrylonitrile-Butadiene-Styrene
PipingSystemsandisthedirectresponsibilityofSubcommitteeF17.91onEditorial
(ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer
and Terminology.
Piping
Current edition approved May 1, 2009. Published June 2009. Originally
approved in 1975. Last previous edition approved in 2007 as F412–07. DOI:
10.1520/F0412-09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Withdrawn. The last approved version of this historical standard is referenced
the ASTM website. on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F412–09
D2683 Specification for Socket-Type Polyethylene Fittings F1473 Test Method for Notch Tensile Test to Measure the
for Outside Diameter-Controlled Polyethylene Pipe and Resistance to Slow Crack Growth of Polyethylene Pipes
Tubing and Resins
D2737 Specification for Polyethylene (PE) Plastic Tubing F1488 Specification for Coextruded Composite Pipe
F1499 Specification for Coextruded Composite
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F 412–07 Designation:F 412–09
Standard Terminology Relating to
1
Plastic Piping Systems
This standard is issued under the fixed designation F 412; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are
generally understood or adequately defined in other readily available sources are not included.
1.2 When a term is used in anASTM document for which Committee F17 is responsible it is included only when judged, after
review, by Subcommittee F17.91 to be a generally usable term.
1.3 Definitions that are identical to those published by otherASTM committees or other standards organizations are identified
with the committee number (for example, D20) or with the abbreviation of the name of the organization (for example, IUPAC
International Union of Pure and Applied Chemistry).
1.4 A definition is a single sentence with additional information included in notes.
1.5 Definitions are followed by the committee responsible for the standard(s) (for example, [F17.26]) and standard numbers(s)
in which they are used (for example, F 714).
2. Referenced Documents
2
2.1 ASTM Standards:
C114 Test Methods for Chemical Analysis of Hydraulic Cement
D 256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D 638 Test Method for Tensile Properties of Plastics
D 648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D 747 Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam
D 790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D 882 Test Method for Tensile Properties of Thin Plastic Sheeting
D 883 Terminology Relating to Plastics
D 907 Terminology of Adhesives
D 1003 Test Method for Haze and Luminous Transmittance of Transparent Plastics
D 1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D 1488 Test Method for Amylaceous Matter in Adhesives
D 1505 Test Method for Density of Plastics by the Density-Gradient Technique
D 1527 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80
D 1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
D 2104 Specification for Polyethylene (PE) Plastic Pipe, Schedule 40
D 2239 Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
D 2241 Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
D 2282 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe
D 2444 Test Method for Determination of the Impact Resistance ofThermoplastic Pipe and Fittings by Means of aTup (Falling
Weight)
D 2447 Specification for Polyethylene (PE) Plastic Pipe, Schedules 40 and 80, Based on Outside Diameter
D 2513 Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
D 2661 Specification forAcrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
1
This terminology is under the jurisdiction ofASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.91 on Editorial and
Terminology.
Current edition approved Dec. 15, 2007. Published January 2008. Originally approved in 1975. Last previous edition approved in 2006 as F412–06.
Current edition approved May 1, 2009. Published June 2009. Originally approved in 1975. Last previous edition approved in 2007 as F 412 – 07.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F412–09
D 2666 Specification for Polybutylene (PB) Plastic Tubing
D 2680 Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping
D 2683 Specification for Socket-Ty
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.