ASTM D2380-04(2011)
(Test Method)Standard Test Method for Methanol Content of Formaldehyde Solutions
Standard Test Method for Methanol Content of Formaldehyde Solutions
SIGNIFICANCE AND USE
This test method provides a measurement of methanol content of formaldehyde solutions. The results of these measurements can be used for specification acceptance.
This test method is applicable to 37 % formaldehyde solutions containing 0 to 2 %, 6 to 8 %, or 12 to 15 % methanol.
SCOPE
1.1 This test method provides for the calculation of the methanol content of commercially available 37 % formaldehyde solutions and is based on the relationship of specific gravity to formaldehyde and methanol content. Separate equations are given for three ranges of methanol: 0 to 2 %, 6 to 8 %, and 12 to 15 %.
1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 4.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2380 − 04 (Reapproved 2011)
Standard Test Method for
Methanol Content of Formaldehyde Solutions
This standard is issued under the fixed designation D2380; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* E29 Practice for Using Significant Digits in Test Data to
Determine Conformance with Specifications
1.1 This test method provides for the calculation of the
methanol content of commercially available 37 % formalde-
3. Significance and Use
hyde solutions and is based on the relationship of specific
gravity to formaldehyde and methanol content. Separate 3.1 This test method provides a measurement of methanol
equations are given for three ranges of methanol: 0 to 2 %, 6 to
content of formaldehyde solutions. The results of these mea-
8 %, and 12 to 15 %. surements can be used for specification acceptance.
1.2 For purposes of determining conformance of an ob-
3.2 This test method is applicable to 37 % formaldehyde
served or a calculated value using this test method to relevant solutions containing 0 to 2 %, 6 to 8 %, or 12 to 15 %
specifications, test result(s) shall be rounded off “to the nearest
methanol.
unit” in the last right-hand digit used in expressing the
specification limit, in accordance with the rounding-off method
4. Hazards
of Practice E29.
4.1 Formaldehyde and formaldehyde solutions are hazard-
1.3 The values stated in SI units are to be regarded as
ous. Minimize exposure and contact to avoid acute effects and
standard. No other units of measurement are included in this possible sensitizing. Consult the supplier’s Material Safety
standard.
Data Sheet for specific hazard information.
1.4 For hazard information and guidance, see the supplier’s
5. Procedure
Material Safety Data Sheet.
5.1 Determine the apparent specific gravity of the material
1.5 This standard does not purport to address all of the
by a method that is accurate to the fourth decimal place, the
safety concerns, if any, associated with its use. It is the
temperature of both the specimen and the water being 25°C.
responsibility of the user of this standard to establish appro-
See Guide D268.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. Specific hazard
5.2 Determine the formaldehyde content of the material in
statements are given in Section 4.
accordance with Test Method D2194.
2. Referenced Documents
6. Calculation
2.1 ASTM Standards:
6.1 Calculate the methanol content as follows using the
D268 Guide for Sampling and Testing Volatile Solvents and
appropriate equation for the expected methanol range:
Chemical Intermediates for Use in Paint and Related
6.1.1 0 to 2 % Methanol:
Coatings and Material
Methanol, wt% 5 ~1.001710.003F 2 D!/0.00253 (1)
D2194 Test Method for Concentration of Formaldehyde
Solutions
6.1.2 6 to 8 % Methanol:
Methanol, wt% 5 1.001510.003F 2 D /0.00250 (2)
~ !
This test method is under the jurisdiction of ASTM Committee D01 on Paint
6.1.3 12 to 15 % Methanol :
and Related Coatings, Materials, andApplications and is the direct responsibility of
Subcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates.
Methanol, wt% 5 1.021010.0025F 2 D /0.00257 (3)
~ !
Current edition approved Feb. 1, 2011. Published February 2011. Originally
approved in 1965. Last previous edition approved in 2004 as D2380 – 04. DOI: where:
10.1520/D2380-04R11.
F = formaldehyde content, weight %, a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.