ASTM B722-06(2011)
(Specification)Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Seamless Pipe and Tube
Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Seamless Pipe and Tube
ABSTRACT
This specification covers hot or cold-finished seamless pipes made from NUS N06333 alloy that is intended for heat and corrosion resistance applications. The chemical composition, dimensions and mechanical properties for the welded pipes should be in accordance with those contained in this document and other ASTM documents specified herein.
SCOPE
1.1 This specification covers alloy N06333 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat-resisting applications and general corrosive service. The general requirements for pipe and tube are covered in Specification B829.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B722 −06(Reapproved 2011)
Standard Specification for
Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon
Alloy (UNS N06333) Seamless Pipe and Tube
This standard is issued under the fixed designation B722; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* specification. Examples of such requirements include but are
not limited to the following:
1.1 This specification covers alloy N06333 in the form of
4.1.1 Alloy name or UNS number.
hot-finished and cold-finished seamless pipe and tube intended
4.1.2 ASTM designation and year of issue.
for heat-resisting applications and general corrosive service.
4.1.3 Quantity (feet or number of pieces).
The general requirements for pipe and tube are covered in
Specification B829.
4.1.4 Dimensions:
4.1.4.1 Pipe size.
1.2 The values stated in inch-pound units are to be regarded
4.1.4.2 Tube dimensions (outside or inside diameter and
as standard. The values given in parentheses are mathematical
nominal wall thickness).
conversions to SI units that are provided for information only
and are not considered standard. 4.1.4.3 Length (specific or random).
4.1.5 Hydrostatic Test or Nondestructive Electric Test—
1.3 This standard does not purport to address all of the
Specify type of test (see 5.2).
safety concerns, if any, associated with its use. It is the
4.1.6 Certification—State if certification is required.
responsibility of the user of this standard to become familiar
with all hazards including those identified in the appropriate 4.1.7 Samples for Product (Check) Analysis—State whether
samples for product (check) analysis should be furnished.
Material Safety Data Sheet (MSDS) for this product/material
as provided by the manufacturer, to establish appropriate
4.1.8 Purchaser Inspection—If purchaser wishes to witness
safety and health practices, and determine the applicability of
tests or inspection of material at place of manufacture, the
regulatory limitations prior to use.
purchase order must so state indicating which tests or inspec-
tions are to be witnessed.
2. Referenced Documents
2.1 ASTM Standards: 5. Mechanical and Other Requirements
B829 Specification for General Requirements for Nickel and
5.1 Tension Test—The mechanical properties of the material
Nickel Alloys Seamless Pipe and Tube
at room temperature shall conform to those shown in Table 1.
The sampling and specimen preparation are covered in Speci-
3. General Requirement
fication B829.
3.1 Material furnished under this specification shall con-
5.2 Hydrostatic or Nondestructive Electric Test—Each pipe
form to the applicable requirements of Specification B829
or tube shall be subjected to either the hydrostatic test or to the
unless otherwise provided herein.
nondestructive electric test. The type of test to be used shall be
4. Ordering Information at the option of the manufacturer, unless otherwise specified in
the purchase order.
4.1 It is the responsibility of the purchaser to specify all
requirements that are necessary for material ordered under this
6. Dimensions and Permissible Variations
6.1 The requirements of Specification B829 will apply
This specification is under the jurisdiction of ASTM Committee B02 on
except for hot-finished pipe and tube dimensional requirements
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.07 on Refined Nickel and Cobalt and Their Alloys. shown in Table 2.
Current edition approved June 1, 2011. Published June 2011. Originally
approved in 1983. Last previous edition approved in 2006 as B722 – 06. DOI:
7. Chemical Requirements
10.1520/B0722-06R11.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
7.1 The material shall conform to the requirements as to
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
chemical composition specified in Table 3. One test is required
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. for each lot as defined in Specification B829.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor D
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.