iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E236-66(2006)

(Specification)

Standard Specification for Apparatus For Microdetermination Of Alkoxyl Groups

Standard Specification for Apparatus For Microdetermination Of Alkoxyl Groups

ABSTRACT
This specification covers the design and dimensional requirements for the apparatus used in the microdetermination of methoxyl and ethoxyl groups in organic compounds. This apparatus is composed of a reaction flask, condenser with scrubber, delivery tube, and two types of receivers—one for volumetric analysis, and the other for gravimetric analysis.
SCOPE
1.1 This specification covers apparatus for the microdetermination of methoxyl and ethoxyl groups in organic compounds.  Note 1-This specification was originally developed by the Committee on Microchemical Apparatus, Division of Analytical Chemistry, American Chemical Society.

General Information

Status
Historical
Publication Date
31-Oct-2006
ICS
71.040.20 - Laboratory ware and related apparatus
Technical Committee
E41 - Laboratory Apparatus
Drafting Committee
E41.01 - Laboratory Ware and Supplies
Current Stage
Ref Project

Relations

Replaces
ASTM E236-66(1996) - Standard Specification for Apparatus For Microdetermination Of Alkoxyl Groups
Effective Date
01-Nov-2006
Replaced By
ASTM E236-66(2011) - Standard Specification for Apparatus for Microdetermination of Alkoxyl Groups
Effective Date
01-Dec-2011

Buy Standard

ASTM E236-66(2006) - Standard Specification for Apparatus For Microdetermination Of Alkoxyl GroupsASTM E236-66(2006) - Standard Specification for Apparatus For Microdetermination Of Alkoxyl Groups
PreviousNext
Technical specification
ASTM E236-66(2006) - Standard Specification for Apparatus For Microdetermination Of Alkoxyl Groups
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E236 – 66 (Reapproved 2006)
Standard Specification for
1
Apparatus for Microdetermination of Alkoxyl Groups
This standard is issued under the fixed designation E236; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers apparatus for the microdeter-
mination of methoxyl and ethoxyl groups in organic com-
pounds.
NOTE 1—This specification was originally developed by the Committee
on MicrochemicalApparatus, Division ofAnalytical Chemistry,American
2
Chemical Society.
2. Reaction Flask
2.1 The reaction flask shall be of borosilicate glass and shall
conform to the requirements of Fig. 1.
3. Condenser with Scrubber
3.1 The West-type condenser with scrubber shall be of
borosilicate glass and conform to the requirements of Fig. 2.
NOTE 2—Spent scrubbing solution may be removed from the scrubber
by inserting through the side arm of the scrubber a drawn-out medicine
dropper or small rubber tube connected to a vacuum source.
NOTE 3—The scrubber is constricted to prevent scrubbing solution
All dimensions are in millimetres.
from being sucked back into the reaction flask or carried over into the
FIG. 1 Reaction Flask
receiver.
5. Receivers
4. Delivery Tube
5.1 Two types of receivers are specified, as follows:
4.1 The delivery tube shall be of borosilicate glass and
3
5.1.1 Receiver for Volumetric Analysis shall be of borosili-
conform to the requirements of Fig. 3.
cate glass and conform to the requirements of Fig. 4.
5.1.2 Receiver for Gravimetric Analysis shall be of boro-
silicate glass and conform to the requirements of Fig. 5.
1
This specification is under the jurisdiction of ASTM Committee E41 on
Laboratory Apparatus and is the direct responsibility of Subcommittee E41.01 on
6. Keywords
Apparatus.
Current edition approved Nov. 1, 2006. Published December 2006. Originally
6.1 alkoxyl; apparatus; groups; microdetermination
´1
approved in 1964. Last previous edition approved in 2001 as E236 – 66 (2001) .
DOI: 10.1520/E0236-66R06
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E617-23(Specification)
Standard Specification for Laboratory Weights and Precision Mass Standards

ABSTRACT
This specification covers laboratory weights and precision mass standards including their principal physical characteristics and metrological requirements. Maximum permissible error, magnetic property, density, and surface roughness for each weight shall be within the limits indicated in this specification. Physical characteristics shall be based on construction, design, surface area, materials, magnetism, density, surface finish, weight adjustment, and marking.
SCOPE
1.1 This specification covers weights and mass standards used in laboratories, specifically classes 000, 00, 0, 1, 2, 3, 4, 5, 6, and 7. This specification replaces National Bureau of Standards Circular 547, Section 1, which is out of print.  
1.2 This specification and calibration method is intended for use by weight manufacturers, national metrology institutes, weight calibration laboratories, accreditation bodies, users of weights, and regulatory bodies.  
1.3 This specification contains the principal physical characteristics and metrological requirements for weights that are used.  
1.3.1 For the verification of weighing instruments;  
1.3.2 For the calibration of weights of a lower class of accuracy; and  
1.3.3 With weighing instruments.  
1.4 Maximum Permissible Errors (formerly tolerances) and design restrictions for each class are described in order that both individual weights or sets of weights can be chosen for appropriate applications.  
1.5 Weight manufacturers must be able to provide evidence that all new weights comply with specifications in this standard (for example, material, density, magnetism, surface finish, mass values, uncertainties) to make any claim of compliance to Specification E617, Maximum Permissible Errors, weight classes, or metrological traceability.  
1.5.1 During subsequent calibrations, calibration laboratories must meet the requirements of ISO/IEC 17025:2017.  
1.5.2 Subsequent calibrations must meet all the requirements, including Sections 7, 8, and 9, Table 8 and Table 11 (environmental parameters) to make any claim of compliance to Specification E617, Maximum Permissible Errors, weight classes, or metrological traceability.
Note 1: Requirements set forth in NIST IR 6969 and NIST IR 5672 are compliant with all the requirements of Specification E617, Sections 7, 8, and 9.  
1.6 The values stated in SI units are to be regarded as standard.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    16 pages
    English language
    sale 15% off
  • Technical specification
    16 pages
    English language
    sale 15% off
ASTM
ASTM E1154-23(Specification)
Standard Specification for Piston or Plunger Operated Volumetric Apparatus and Operator Qualification

ABSTRACT
This specification covers piston or plunger operated volumetric apparatus (POVA), in particular, the requirements, operating conditions, and test methods. POVA covered by this specification are pipettes, dispensers (with and without valve), dilutors, and displacement burets (with and without valve). Single measurement, replicate delivery, durability, functional (such as tests for leakage, broken parts, existence of air bubbles, and contamination), volumetric, and gravimetric tests shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers requirements, operating conditions, and test procedures for piston or plunger operated volumetric apparatus (POVA), as well as requirements for pipette operator training and qualification.  
1.2 This specification is applicable to all types of POVA. The following precautionary caveat pertains only to the test procedure portion, Annex A1 and Annex A2, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    16 pages
    English language
    sale 15% off
  • Technical specification
    16 pages
    English language
    sale 15% off
ASTM
ASTM E1379-90(2022)(Specification)
Standard Specification for Laboratory Glass Dewar Flask

ABSTRACT
This specification provides the material and performance requirements for glass Dewar flasks suitable for general laboratory use. Flasks shall be made of Type I, Class A borosilicate glass conforming to specified maximum residual thermal stress. The properties to which the flasks shall conform are appearance, design, capacity, and dimensions.
SCOPE
1.1 This specification provides standard material and performance requirements for glass Dewar flasks suitable for general laboratory use.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1378-99(2022)(Specification)
Standard Specification for Laboratory Glass Multiple Neck Distilling/Boiling Flasks

ABSTRACT
This specification provides the standard appearance, capacity, design, and dimensional requirements for eight types of multiple neck distilling/boiling glass flasks for laboratory use. Flasks, which shall be made of borosilicate glass conforming to specified maximum residual thermal stresses, are available in the following types: Type I, standard taper necks of equal height; Type II, three tooled necks of unequal height; Type III, three standard taper necks of unequal height; Type IV, three standard taper necks of equal height; Type V, three tooled necks that are angled; Type VI, three standard taper necks that are angled; Type VII, two standard taper necks of unequal height; and Type VIII, two standard taper necks that are angled.
SCOPE
1.1 This specification provides standard dimensional requirements for multiple neck distilling/boiling flasks.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM E1189-00(2022)(Specification)
Standard Specification for Micro-Burets (Koch Style)

ABSTRACT
This specification covers two styles of "Koch" type glass microburets for general laboratory use. Burets shall be made from Type I, Class A or B glass. Both burets shall have permanently attached stopcocks with either glass plugs, or PTFE plugs. Materials shall be tested and the individual grades shall conform to design requirements with the specified values of capacity, scale length, diameter, outflow time, and tolerance.
SCOPE
1.1 This specification covers two styles of glass micro-burets of the “Koch” type for general laboratory use.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1377-99(2022)(Specification)
Standard Specification for Laboratory Glass Kjeldahl Flasks

ABSTRACT
This specification provides standard dimensional requirements for glass Kjeldahl flasks for nitrogen digestion analysis. The ungraduated flasks, Type I, and graduated flasks, Type II, shall conform to the specified capacities. Flasks shall be made of borosilicate glass, conforming to the required maximum residual stress, tolerance of volumetric accuracy, and dimensions.
SCOPE
1.1 This specification provides standard dimensional requirements for glass Kjeldahl flasks for nitrogen digestion analysis.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM E147-61(2022)(Specification)
Standard Specification for Apparatus for Microdetermination of Nitrogen by Kjeldahl Method

ABSTRACT
This specification covers the design and dimensional requirements for the digestion and distillation apparatus used for the microdetermination of nitrogen by the Kjeldahl method, and modifications thereof at atmospheric pressure. This apparatus is comprised primarily of digestion flasks, micro Kjeldahl digestion rack, one-piece model distillation apparatus, and Pregl (Parnas-Wagner) type distillation apparatus.
SCOPE
1.1 This specification covers digestion and distillation apparatus used for the microdetermination of nitrogen by the Kjeldahl method, and modifications thereof at atmospheric pressure.  
Note 1: This specification is based on those originally developed by the Committee on Microchemical Apparatus, Division of Analytical Chemistry, American Chemical Society.2  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM E1406-95(2022)(Specification)
Standard Specification for Laboratory Glass Filter Flasks

ABSTRACT
This specification provides standard dimensional requirements for glass filtering flasks suitable for general laboratory use. Glass filter flasks shall be in the following types: Type I, Type II (Class 1 and Class 2), and Type III (Class 1, Class 2, and Class 3). Flasks shall be made of the specified borosilicate glass and shall conform to the prescribed maximum residual thermal stress. The general appearance of the flasks are illustrated. The design for (1) conical flasks including bottom concavity and bottom heel radius, (2) neck finish, and (3) side-arm are specified. Filtering flasks shall conform to the prescribed requirements for (1) capacity; (2) dimensions such as body outside diameter, overall height, rubber stopper size, bottom and heel wall thickness, and base/heel radius; and (4) pressure resistance. Each flask shall be permanently marked with the name or known trademark of the manufacturer and the nominal capacity. There shall be an area on one side of the flask for marking with a pencil.
SCOPE
1.1 This specification provides standard dimensional requirements for glass filtering flasks suitable for general laboratory use.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM E784-89(2022)(Specification)
Standard Specification for Clamps, Utility, Laboratory, and Holders, Buret and Clamp

ABSTRACT
This specification covers clamps and clamp holders for use in securing laboratory apparatus to support stands. The clamp and clamp holders are classified into types, sizes and classes and are presented in details. Clamps and clamp holders shall be manufactured from aluminum-base alloy, zinc-base alloy, or cast iron. Fittings such as screws, nuts, and rivets for clamps and clamp holders shall be forged aluminum or chemical-resistant alloy for either aluminum-base alloy or zinc-base alloy clamps and clamp holders. Component springs of clamps shall be phosphor bronze or corrosion-resistant steel. Component sleeves of clamps may be rubber, plastic, fiber glass, non-hazardous minerals, or replaceable plastic.
SCOPE
1.1 This specification covers clamps and clamp holders for use in securing laboratory apparatus to support stands.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1405-98(2022)(Specification)
Standard Specification for Laboratory Glass Distillation Flasks

ABSTRACT
This specification covers standard dimensional requirements for glass distillation flasks. It includes general purpose flasks and flasks designed for specific tests especially in the petroleum testing area. Distillation flasks shall be of the following types: Type I and Type II. Type II distilling flasks shall be of the following classes: Class 1; Class 2; Class 3; Class 4; and Class 5.
SCOPE
1.1 This specification covers standard dimensional requirements for glass distillation flasks. It includes general purpose flasks and flasks designed for specific tests especially in the petroleum testing area.  
Note 1: For packaging standards, choose among Specifications E920, E1157, and E1133.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off