ASTM B589-94(2005)
(Specification)Standard Specification for Refined Palladium
Standard Specification for Refined Palladium
ABSTRACT
This specification covers refined palladium as sponge, cast bar, and wrought forms in one grade designated as Grade 99.95 (UNS PO3995). The metal may be produced by any refining process that yields a product capable of meeting the chemical composition requirements prescribed for palladium, platinum group metals other than palladium, gold, silver, lead, tin, zinc, iron, copper, silicon, magnesium, calcium, aluminum, nickel, chromium, cobalt, manganese, and antimony. The surfaces of bars and wrought forms shall exhibit quality generally acceptable to the trade. Sampling requirements for chemical analysis including lot size are given.
SCOPE
1.1 This specification covers refined palladium as sponge, cast bar, and wrought forms (Note 1) in one grade as follows:
1.1.1 Grade 99.95 (UNS PO3995)—Palladium having a purity of 99.95 %.
Note 1—Other forms of unfabricated palladium of commerce are not to be excluded under this specification.
Note 2—For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right hand place of figures used in expressing the limiting value, in accordance with the rounding method of Practice E 29.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B589 −94(Reapproved2005)
Standard Specification for
Refined Palladium
This standard is issued under the fixed designation B589; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2 The surfaces of bars and wrought forms shall exhibit
quality generally acceptable to the trade.
1.1 This specification covers refined palladium as sponge,
cast bar, and wrought forms (Note 1) in one grade as follows:
4. Chemical Composition
1.1.1 Grade 99.95 (UNS PO3995)— Palladium having a
4.1 The refined palladium shall conform to the requirements
purity of 99.95 %.
as to the chemical composition prescribed in Table 1.
NOTE1—Otherformsofunfabricatedpalladiumofcommercearenotto
5. Sampling
be excluded under this specification.
NOTE 2—For the purposes of determining conformance with this
5.1 The value of this material is such that special attention
specification, an observed value obtained from analysis shall be rounded
must be paid to sampling procedures. The purchaser and
to the nearest unit in the last right hand place of figures used in expressing
manufacturer shall agree upon the sampling procedures used.
the limiting value, in accordance with the rounding method of Practice
E29.
5.2 Lot Size—Sampling lots shall consist of the following:
1.2 The values stated in inch-pound units are to be regarded
5.2.1 Sponge—A single refining lot, and
as the standard. The values given in parentheses are for
5.2.2 Other Forms— A single melt or primary consolida-
information only.
tion.
1.3 This standard does not purport to address all of the
6. Method of Analysis
safety concerns, if any, associated with its use. It is the
6.1 Pending the development of standardASTM methods of
responsibility of the user of this standard to become familiar
chemical or spectrographic analysis, or both, the methods to be
with all hazards including those identified in the appropriate
used shall be a matter of agreement between the manufacturer
Material Safety Data Sheet for this product/material as pro-
and the purchaser.
vided by the manufacturer, to establish appropriate safety and
health practices, and determine the applicability of regulatory
7. Rejection and Rehearing
limitations prior to use.
7.1 Material that fails to conform to the requirements of this
2. Referenced Documents specification may be rejected. Rejection should be reported to
the producer or supplier promptly and in writing. In case of
2.1 ASTM Standards:
dissatisfaction with the results of the test, the producer or
E29 Practice for Using Significant Digits in Test Data to
supplier may make claim for rehearing.
Determine Conformance with Specifications
7.1.1 If the palladium satisfies the requirements of this
specification, it shall not be rejected for defects in the products
3. Materials and Manufacture
in which it is used.
3.1 The metal may be produced by any refining process that
7.2 Investigation of Claims—In a question of chemical
yields a product capable of meeting the chemical requirements
composition, a new sample shall be drawn by representatives
of this specification. The purchaser, upon request, shall be
of both parties in accord
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.