iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6719-05

(Guide)

Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor Covering

Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor Covering

SCOPE
1.1 This guide provides users with an index of procedures in the form of test methods, practices, and related documents that are currently used in industry for determination of properties of pile yarn floor covering. This guide is not considered as all-inclusive for testing procedures related to pile yarn floor covering.
1.1.1 It is the responsibility of the user to choose from this guide those procedures that provide test information on properties of interest for pile yarn floor covering that relate to its physical and esthetic properties and performance.
1.1.2 Procedures for particular properties appear in the following sections:
1.2 In general, values stated in SI units are to be regarded as the standard. Values given in parentheses are for information only and may be approximate.
1.2.1 Some of the listed procedures may cite other units as standard. In this event, language of the procedure is controlling.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
28-Feb-2005
ICS
97.150 - Floor coverings
Technical Committee
D13 - Textiles
Drafting Committee
D13.21 - Pile Floor Coverings
Current Stage
Ref Project

Relations

Replaces
ASTM D6719-04 - Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor Covering
Effective Date
01-Mar-2005
Replaced By
ASTM D6719-07 - Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor Covering
Effective Date
01-Jan-2007
Referred By
ASTM D5253-04(2016) - Standard Terminology Relating to Floor Coverings and Textile Upholstered Furniture
Effective Date
01-Mar-2005
Referred By
ASTM D5684-19a - Standard Terminology Relating to Pile Floor Coverings
Effective Date
01-Mar-2005

Buy Standard

ASTM D6719-05 - Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor CoveringASTM D6719-05 - Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor Covering
PreviousNext
Guide
ASTM D6719-05 - Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor Covering
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6719–05
Standard Guide for
Standard Test Methods and Practices for Evaluating Pile
1
Yarn Floor Covering
This standard is issued under the fixed designation D 6719; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
1.1 Thisguideprovidesuserswithanindexofproceduresin
bility of regulatory limitations prior to use.
the form of test methods, practices, and related documents that
arecurrentlyusedinindustryfordeterminationofpropertiesof
2. Referenced Documents
pile yarn floor covering. This guide is not considered as
2
2.1 ASTM Standards:
all-inclusive for testing procedures related to pile yarn floor
D 123 Terminology Relating To Textiles
covering.
D 418 Test Methods for Testing Pile Yarn Floor Covering
1.1.1 It is the responsibility of the user to choose from this
3
Construction
guide those procedures that provide test information on prop-
D 629 Test Method for Quantitative Analysis of Textiles
erties of interest for pile yarn floor covering that relate to its
D 1335 Test Method for Tuft Bind of Pile Yarn Floor
physical and esthetic properties and performance.
Covering
1.1.2 Procedures for particular properties appear in the
D 1776 Practice for Conditioning and Testing Textiles
following sections:
D 2646 TestMethodsforBackingFabricsCharacteristicsof
Property Section
Pile Yarn Floor Coverings
Surface Appearance Change 8.1-8.32
D 2859 TestMethodforIgnitionCharacteristicsofFinished
Antimicrobial 8.5
Textile Floor Covering Materials
Binding Sites 8.6
D 3936 Test Method for Resistance to Delamination of the
Backing Characteristics 8.7
Colorfastness 8.8-8.12
Secondary Backing of Pile Yarn Floor Coverings
Carpets, Cleaning 8.13 and 8.14
D 5251 Practice for the Operation of the Tetrapod Walker
Conditioning 7
Tester
Delamination Resistance 8.15
Fiber Analysis 8.16
D 5252 Practice for the Operation of the Hexapod Tumble
Flammability 8.17-8.20
Drum Tester
Pile Thickness 8.21
D 5417 Practice for the Operation of the Vetterman Drum
Mass per Unit Area 8.22
Soiling 8.23-8.26
Tester
Stain Resistance 8.27
D 5684 Terminology Relating to Pile Floor Coverings
Static 8.28
Tuft Bind 8.29 D 5793 Test Method for Binding Sites Per Unit Length or
Tuft Height 8.30
Width of Pile Yarn Floor Coverings
Tuft Element Length 8.31
D 5823 Test Methods for Tuft Height of Pile Yarn Floor
Durability 8.33
Coverings
1.2 In general, values stated in SI units are to be regarded as
D 5848 Test Method for Mass Per Unit Area of Pile Yarn
the standard. Values given in parentheses are for information
Floor Coverings
only and may be approximate.
D6119 Practice for Creating Surface Appearance Changes
1.2.1 Some of the listed procedures may cite other units as
in Pile Yarn Floor Covering From Foot Traffic
standard. In this event, language of the procedure is control-
D 6283 Test Method for Tuft Element Length of Uncoated
ling.
Pile Yarn Floor Covering
1.3 This standard does not purport to address all of the
D 6540 Test Method for Accelerated Soiling of Pile Yarn
safety concerns, if any, associated with its use. It is the
Floor Covering
1 2
This guide is under the jurisdiction of ASTM Committee D13 on Textiles and For referenced ASTM standards, visit the ASTM website, www.astm.org, or
is the direct responsibility of Subcommittee D13.21 on Pile Yarn Floor Covering. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved March 1, 2005. Published March 2005. Originally Standards volume information, refer to the standard’s Document Summary page on
published in 2001. Last previous edition approved in 2004 as D 6719–04. the ASTM website.
3
Discontinued, see 1997 Annual Book of ASTM StandardsVol 07.01.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D6719–05
D 6859 Test Method for Pile Thickness of Finished Level 5.1.1 Uncoated Floor Covering—The basic sampling unit
Pile Yarn Floor Coverings of uncoated floor covering is a production roll.
D 6962 Practice for Operation of a Roller Chair Tester for 5.1.2 Coated Floor Covering—The basic sampling unit of
Pile Yarn Floor Coverings coated floor covering is a shipping roll. The number of
E 122 Practice for Choice of Sample Size to Estimate a shipping rolls obtained from each production roll ranges from
Measure of Quality for a Lot Process one to over ten.
E 648 Test Method for Critical Radiant Flux of Floor
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7330-22(Test Method)
Standard Test Method for Assessment of Surface Appearance Change in Pile Floor Coverings Using Standard Reference Scales

SIGNIFICANCE AND USE
5.1 The determination of surface appearance change in pile yarn floor covering is useful in quality and cost control during manufacture of pile yarn floor covering. This test method is considered satisfactory for acceptance testing of commercial shipments because current estimates of between laboratory precision are acceptable, and this test method is commonly used in trade for acceptance testing.  
5.2 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use the samples for such comparative tests that are as homogenous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved shall be compared using a statistical test for unpaired data, a probability level chosen prior to the testing series. If a bias is found either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.
SCOPE
1.1 This test method covers the assessment of changes of surface appearance of pile floor coverings after exposure to actual or simulated foot traffic. This test method applies to pile yarn floor coverings that are, or have been, installed; laboratory floor-trafficked samples; or textiles floor coverings trafficked by mechanical traffic simulators. The subjective assessment is facilitated by use of reference scales that are based on digital images of representative pile yarn floor covering styles and constructions.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5793-18(2022)(Test Method)
Standard Test Method for Binding Sites per Unit Length or Width of Pile Yarn Floor Coverings

SIGNIFICANCE AND USE
5.1 This test method is useful in quality and cost control during manufacture. Both appearance and performance of pile yarn floor coverings can be affected by the number of binding sites per length and width.  
5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because current estimates of between-laboratory precision are acceptable and the method is used extensively in the trade for acceptance testing.  
5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is statistical bias between them using competent statistical assistance. As a minimum, use test samples for such comparative tests that are as homogeneous as possible, drawn form the same lot of material as the samples that resulted in the disparate results during initial testing, and that are randomly assigned in equal numbers to each laboratory for testing. The test results from the laboratories should be compared using a statistical test for unpaired data at a probability level chosen prior to the testing series. If a bias is found either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the know bias.
SCOPE
1.1 This test method describes the measurement of the number of binding sites per unit length or width of machine-made, woven, knitted, and tufted pile yarn floor covering both before and after adhesive backing application.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7241-22(Test Method)
Standard Test Method for Pile Thickness of Finished Multilevel Pile Yarn Floor Covering

SIGNIFICANCE AND USE
5.1 The determination of pile thickness of multilevel pile yarn floor covering is useful in quality and cost control during manufacture of pile yarn floor covering. The appearance and performance may be affected by changes in pile thickness of pile yarn floor coverings. This test method is considered satisfactory for acceptance testing of commercial shipments because current estimates of between laboratory precision are acceptable, and this test method is commonly used in the trade for acceptance testing.  
5.2 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use the samples for such comparative tests that are as homogenous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, a probability level chosen prior to the testing series. If a bias is found either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.
SCOPE
1.1 This test method covers the determination of pile thickness of finished multilevel pile yarn floor covering using a thickness measuring instrument having a stationary surface (platen), a circular pressure foot under specified force, and capable of being moved vertically above the platen.  
1.2 This test method is applicable only to finished multilevel loop pile constructions.
Note 1: Determination of pile thickness of multilevel pile yarn floor coverings was previously contained within Test Method D418. For user convenience, Subcommittee D13.21 subdivided Test Method D418 into separate standards of which this test method is one.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D7983-17(2022)(Test Method)
Standard Test Method for Shrinkage of Carpet Backing Fabrics

SIGNIFICANCE AND USE
5.1 This test method can be useful in characterizing and comparing shrinkage properties of both primary and secondary backing fabrics. This test method is considered satisfactory for acceptance testing of commercial shipments because current estimates of between-laboratory precision are acceptable, and this test method is commonly used in the trade for acceptance testing.  
5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is statistical bias between them using competent statistical assistance. As a minimum, use test samples for such comparative tests that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in the disparate results during initial testing, and that are randomly assigned in equal numbers to each laboratory for testing. The test results from the laboratories should be compared using statistical test for unpaired data at a probability level chosen prior to the testing series. If a bias is found either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.
SCOPE
1.1 This test method covers the procedure for evaluating shrinkage, in both wet and dry conditions, of woven, knitted and nonwoven backing fabrics designed for use in the manufacture of pile yarn floor coverings. Determination of carpet backing shrinkage was previously contained within Test Methods D2646. For consistency, Subcommittee D13.21 extracted this portion and created a separate test method.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6540-22(Test Method)
Standard Test Method for Accelerated Soiling of Pile Yarn Floor Covering

SIGNIFICANCE AND USE
5.1 This test method may be used to soil test specimens in the absence of abrasive wear and texture changes under controlled conditions using a standard synthetic soil, or as a preliminary step to other procedures.  
5.2 This test method will provide a uniformly soiled test specimen to evaluate, is reproducible (see section 11), and is economical for Testing Laboratories.  
5.3 This test method has been found to give results similar to the actual floor service soiling, but its use is recommended only as a screening test method and not as a replacement for floor testing.  
5.4 The acceptance criteria of this test method shall be set by mutual agreement between the purchaser and supplier.
SCOPE
1.1 This test method describes the equipment, and the test method for assessing the propensity of pile yarn floor coverings to soiling in the absence of abrasive wear and texture changes, using a standard synthetic soil composition.  
1.2 This test method is applicable for use in testing unused pile yarn floor covering of all types. It is not applicable for use in testing used pile yarn floor covering.  
1.3 This test method can be used to compare the soiling propensity of two or more carpets; or it can be used to soil carpets as a preliminary step to other test procedures.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6719-22e1(Guide)
Standard Guide for Standard Test Methods and Practices for Evaluating Pile Yarn Floor Covering

SIGNIFICANCE AND USE
4.1 This guide is useful to select test methods or practices, or both, that are commonly used in industry for evaluating pile yarn floor covering. Refer to the test method or practice cited for the property of interest for significance and use statements.
SCOPE
1.1 This guide provides users with an index of procedures in the form of test methods, practices, and related documents that are currently used in industry for determination of properties of pile yarn floor covering. This guide is not considered as all-inclusive for testing procedures related to pile yarn floor covering.  
1.1.1 It is the responsibility of the user to choose from this guide those procedures that provide test information on properties of interest for pile yarn floor covering that relate to its physical and esthetic properties and performance.  
1.1.2 Procedures for properties appear in the following sections:    
Property  
Section  
Surface Appearance Change  
8.1, 8.2, 8.3, 8.4, 8.31, and 8.35  
Antimicrobial  
8.5  
Binding Sites  
8.6  
Backing Characteristics  
8.7  
Colorfastness to Light, Crocking,
Ozone, Water, and Oxides
of Nitrogen  
8.8 – 8.12  
Carpets, Cleaning  
8.13 and 8.14  
Conditioning  
7  
Delamination Resistance  
8.15  
Fiber Analysis  
8.16  
Flammability  
8.17 – 8.20  
Pile Thickness  
8.21  
Mass per Unit Area  
8.22  
Soiling  
8.23 – 8.25  
Stain Resistance  
8.26  
Static  
8.27  
Tuft Bind  
8.28  
Tuft Height  
8.29  
Tuft Element Length  
8.30  
Durability  
8.32  
Edge Ravel  
8.33  
Dimensional Stability  
8.34  
Fluorine Content  
8.36  
Colorfastness to Sodium  
8.37  
Installation of Commercial Carpet  
8.38  
Installation of Residential Carpet  
8.39  
Maintenance and Cleaning
of Commercial Carpet  
8.40  
Maintenance and Cleaning
of Residential Carpet  
8.41  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are non-rationalized mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.2.1 Some of the listed procedures may cite other units as standard. In this event, language of the procedure is controlling.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7570-17(2021)e1(Test Method)
Standard Test Method for Evaluation of Dimensional Stability of Pile Yarn Floor Covering

SIGNIFICANCE AND USE
5.1 The determination of dimensional change of pile yarn floor covering is useful in quality and cost control during manufacture of pile yarn floor covering. The appearance and performance may be affected by the changes in the dimensions of pile yarn floor covering. This test method is considered satisfactory for acceptance testing of commercial shipment because current estimates of between laboratory precision are acceptable, and this method is commonly used in the trade for acceptance testing.  
5.2 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them using competent statistical assistance. As a minimum use the samples for such comparative tests that are as homogenous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, a probability level chosen prior to the testing series. If a bias is found either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.
SCOPE
1.1 This test method covers the determination of dimensional changes in the lengthwise and width-wise direction and distortion likely to occur when pile floor coverings are exposed to various conditions of moisture and heat. This method is applicable to all pile floor coverings including carpet module form.  
1.2 This method is applicable to machine made pile yarn floor covering.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversion to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5417-21(Practice)
Standard Practice for Operation of the Vettermann Drum Tester

SIGNIFICANCE AND USE
5.1 This equipment may be used to bring about the changes in texture on the surface of pile floor covering caused by mechanical action.  
5.2 The acceptance criteria of this practice shall be set by mutual agreement between the purchaser and the supplier.
SCOPE
1.1 This practice describes the equipment and operation of the Vettermann drum tester for testing pile yarn floor covering to produce changes in appearance and color due to changes in surface structure by mechanical action.  
1.2 This practice is only applicable for use in testing unused pile floor covering of all types. It is not applicable for use in testing used pile yarn floor coverings.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1335-21(Test Method)
Standard Test Method for Tuft Bind of Pile Yarn Floor Coverings

SIGNIFICANCE AND USE
5.1 Test Method D1335 for tuft bind of pile yarn floor coverings is being used for acceptance testing of commercial shipments. Comparative tests as directed in 5.1.1 may be advisable.  
5.1.1 In case of a dispute arising from differences in reported test results using this test method, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended from the investigation of bias. As a minimum, the two parties should take a group of test samples that are homogeneous as possible and are from a lot of material of the type in question. The test samples should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using appropriate statistical analysis, and a probability level chosen by the two parties before testing begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias.  
5.2 The satisfactory performance of a pile yarn floor covering depends to a considerable extent on the maintenance of its original appearance. In a cut pile yarn floor covering an inadequate tuft bind may result in complete loss of pile in areas exposed to severe wear. In a looped pile yarn floor covering with inadequate tuft bind the pile loops may be pulled out to form unsightly long loops which may be hazardous.
SCOPE
1.1 This test method covers the measurement of force required to pull or break a tuft from a pile floor covering sample.  
1.2 This test method is applicable to both cut and loop pile yarn floor covering.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6283-21(Test Method)
Standard Test Method for Tuft Element Length of Uncoated Pile Yarn Floor Coverings

SIGNIFICANCE AND USE
5.1 The determination of the tuft length of pile yarn floor covering is useful in quality and cost control during the manufacture of pile yarn floor covering. Both appearance and performance can be affected by changes in this characteristic.  
5.2 In case there are disputable differences between reported test results for two or more laboratories, comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. At a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which disputable test results were obtained, and that are assigned randomly in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.
SCOPE
1.1 This test method covers the measurement of tuft length and pile yarn length of uncoated pile floor coverings.  
1.2 Usually the tuft elements measured as directed in this test method will each be bound at only one binding site, but this test method also may be used for tuft elements bound at more than one binding site, provided that every tuft element measured is bound at the same number of binding sites.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off