iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5749-01(2006)

(Specification)

Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing

Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing

ABSTRACT
This specification covers reinforced (Type I) and plain (Type II) paper gummed adhesive tapes used for securing and banding paper products and sealing fiberboard boxes. Type I gummed tape may be strippable (Class 1) or nonstrippable (Class 2), while Type II paper-backed gummed tape, whether Grade A (light duty), B (medium duty), or C (heavy duty), is nonstrippable. The tapes shall be manufactured from kraft paper, but the use of recycled pulp in the paper is encouraged as well, and the adhesive used must not have an offensive odor and shall conform to the environmental considerations specified. Type I tapes shall consist of two strips of paper in roll form, while Type II tapes shall consist of one strip of paper in roll form. Upon manufacture, the tape shall be clean and free of folds, sharp creases, tears, cuts, and holes. The tapes shall be examined for visual defects, defects in roll construction, and defects in dimensions. Tests for adhesiveness, tensile strength, and elongation shall be performed as well, and shall conform to the physical properties specified.
SCOPE
1.1 This specification covers plain and reinforced paper gummed adhesive tapes suitable for securing and banding paper products and closing fiberboard boxes.
1.2 This specification is intended to replace Fed. Specs. CID A-A-1492, CID A-A-1671, and PPP-T-45 in part.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
The following safety hazards caveat pertains only to the test methods portion, Section , of this specification:   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Mar-2006
ICS
55.040 - Packaging materials and accessories
Technical Committee
D10 - Packaging
Drafting Committee
D10.14 - Tape and Labels
Current Stage
Ref Project

Relations

Replaces
ASTM D5749-01 - Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing
Effective Date
01-Apr-2006
Replaced By
ASTM D5749-01(2012) - Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing
Effective Date
01-Apr-2012
Referred By
ASTM D1974/D1974M-22 - Standard Practice for Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes
Effective Date
01-Apr-2006

Buy Standard

ASTM D5749-01(2006) - Standard Specification for Reinforced and Plain Gummed Tape for Sealing and SecuringASTM D5749-01(2006) - Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing
PreviousNext
Technical specification
ASTM D5749-01(2006) - Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5749 – 01 (Reapproved 2006)
Standard Specification for
Reinforced and Plain Gummed Tape for Sealing and
1
Securing
This standard is issued under the fixed designation D5749; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
4
1. Scope T401 Fiber Analysis of Paper and Paperboard
4
T410 Weight per Unit Area (Basis Weight or Substance)
1.1 This specification covers plain and reinforced paper
T414 Internal Tearing Resistance of Paper (Elmendorf-
gummed adhesive tapes suitable for securing and banding
4
Type Method)
paper products and closing fiberboard boxes.
UM 575 Water Resistance of Adhesive Bond in Laminated
1.2 ThisspecificationisintendedtoreplaceFed.Specs.CID
4
Paper and Paperboard
A-A-1492, CID A-A-1671, and PPP-T-45 in part.
2.3 ANSI/ASQC Standards:
1.3 The values stated in SI units are to be regarded as
ANSI/ASQCZ1.4 Sampling Procedures and Tables for
standard. The values given in parentheses are for information
5
Inspection by Attributes
only.
ANSI/ASQCZ1.9 Sampling Procedures and Tables for
1.4 The following safety hazards caveat pertains only to the
5
Inspection by Variables for Percent Defective
test methods portion, Section 11, of this specification: This
2.4 Federal Specifications:
standard does not purport to address all of the safety concerns,
PPP-T-45 Tape, Gummed, Paper, Reinforced and Plain, for
if any, associated with its use. It is the responsibility of the user
6
Sealing and Securing
of this standard to establish appropriate safety and health
6
PPP-T-681 Tape, Gummed, Packaging and Packing of
practices and determine the applicability of regulatory limita-
CID A-A-1492 Commercial Item Description Tape,
tions prior to use.
6
Gummed, Paper, Plain
2. Referenced Documents CID A-A-1671 Commercial Item Description Tape,
6
2
Gummed, (Paper, Reinforced, Laminated)
2.1 ASTM Standards:
2.5 ISO Standard:
D685 Practice for Conditioning Paper and Paper Products
ISO 9002 Quality Systems Model for QualityAssurance in
for Testing
5
Production and Installations
D828 Test Method for Tensile Properties of Paper and
Paperboard Using Constant-Rate-of-Elongation Appara-
3. Terminology
3
tus
3.1 Definitions—General definitions for packaging and dis-
D996 Terminology of Packaging and Distribution Environ-
tribution environments are found in Terminology D996.
ments
D1974 Practice for Methods of Closing, Sealing, and Rein-
4. Classification
forcing Fiberboard Boxes
4.1 Type I Reinforced, Laminated:
D3951 Practice for Commercial Packaging
4.1.1 Class 1—Strippable.
2.2 TAPPI Standards:
4.1.2 Class 2—Nonstrippable.
4.2 Type II Plain, Single Ply, Strippable:
1
This specification is under the jurisdiction of ASTM Committee D10 on
4.2.1 Grade A—Light duty, for lightweight packages.
Packaging and is the direct responsibility of Subcommittee D10.14 on Tape and
4.2.2 Grade B—Medium duty, for medium-sized packages.
Labels.
Current edition approved April 1, 2006. Published April 2006. Originally
approved in 1995. Last previous edition approved in 2001 as D5749–01. DOI:
4
10.1520/D5749-01R06. Available from TechnicalAssociation of the Pulp and Paper Industry (TAPPI),
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or P.O.Box105113,Atlanta,GA30348;15TechnologyParkwaySouth,Norcross,GA
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 30092.
5
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute, 25 W. 43rd St., 4th
the ASTM website. Floor, New York, NY 10036.
3 6
Withdrawn. The last approved version of this historical standard is referenced AvailablefromSuperintendentofDocuments,U.SGovernmentPrintingOffice,
on www.astm.org. Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D5749 – 01 (2006)
4.2.3 Grade C—Heavy duty, for heavy-duty packages. 7.3.2 Type I, Class 2, and Type II adhesive shall be capable
of being quickly activated with water. The wetted adhesive
5. Significance and Use
shall show pronounced tackiness and shall cause the tape to
remain so firmly affixed that it cannot be removed without
5.1 Type I is a reinforced gummed tape which may be
strippable (Class 1) or nonstrippable (Class 2). It is intended failure of either the tape or paper when tested in accordance
with 13.6.1.
for use in Methods 2C2, 2C3, and any other methods in
Practice D1974.
7.4 Reinforcing Materials—The reinforcing fibers used in
5.2 Type II is a plain paper-backed nonstri
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7932-17(2023)(Specification)
Standard Specification for Printed, Pressure-Sensitive Adhesive Labels for Use in Extreme Distribution Environments

ABSTRACT
This specification provides a standard means for testing and measuring the performance characteristics of printed, pressure-sensitive adhesive labels for containers, particularly containers to be used in extreme distribution environments (for example, hazardous materials labels, aerospace, military containers). For the purposes of this specification, an extreme distribution environment is one in which it can be reasonably expected to experience direct exposure to deteriorating chemicals, weather, elevated/cold temperatures, and other environmental and physical elements for an extended period of time. This specification includes standard laboratory test methods to simulate exposure to various conditions and measure associated degradation of required performance characteristics. The data from these methods can be used as acceptance criteria between a supplier and customer. This specification covers the physical properties of the labels, as well as workmanship, finish and appearance, acceptance criteria, testing procedures, reporting of all the steps taken, certification, and preparation for delivery.
SCOPE
1.1 This specification provides a standard means to test and measure performance characteristics of printed, pressure-sensitive adhesive labels for containers, particularly containers to be used in extreme distribution environments (for example, hazardous materials labels, aerospace, military containers). For the purposes of this specification, an extreme distribution environment is one in which it can be reasonably expected to experience direct exposure to deteriorating chemicals, weather, elevated/cold temperatures, and other environmental and physical elements for an extended period of time.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM D4577-19(2023)(Test Method)
Standard Test Method for Compression Resistance of a Container Under Constant Load

SIGNIFICANCE AND USE
4.1 In the distribution system for many products there is a phase wherein the packaged product may be stored for a period of time in a manner such that one or more containers are superimposed one upon the other. Failure can occur in any layer4 (see Fig. 1 and Fig. 3).
FIG. 1 Containers Under Constant Load of Dead Weights Imposed by Other Containers
FIG. 2 Container Under Constant Load of Dead Weights
FIG. 3 Containers Under Constant Load in Compression Test Machine With Fixed Platen  
4.2 This test method subjects a container, empty or filled, to a predetermined static load, and to specified atmospheric conditions, if required.
SCOPE
1.1 This test method is designed to determine the resistance of a shipping container to a vertically applied constant load for either a specified time or to failure. The test method may also be used for palletized or unitized load configurations.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D3332-99(2023)(Test Method)
Standard Test Methods for Mechanical-Shock Fragility of Products, Using Shock Machines

SIGNIFICANCE AND USE
4.1 These test methods are intended to provide the user with data on product shock fragility that can be used in choosing optimum-cushioning materials for shipping containers or for product design modification.
SCOPE
1.1 These test methods cover determination of the shock fragility of products. This fragility information may be used in designing shipping containers for transporting the products. It may also be used to improve product ruggedness. Unit or consumer packages, which are transported within an outer container, are considered to be the product for the purposes of these test methods. Two test methods are outlined, as follows:  
1.1.1 Test Method A is used first, to determine the product's critical velocity change.  
1.1.2 Test Method B is used second, to determine the product's critical acceleration.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D1596-14(2023)(Test Method)
Standard Test Method for Dynamic Shock Cushioning Characteristics of Packaging Material

SIGNIFICANCE AND USE
5.1 Dynamic cushioning test data obtained by this test method are applicable to the cushioning material and not necessarily the same as obtained in a package. In addition to the influence of the package, the data can also be affected by the specimen area, thickness, loading rate, and other factors.
SCOPE
1.1 This test method covers a procedure for obtaining dynamic shock cushioning characteristics of packaging materials through acceleration-time data achieved from dropping a falling guided platen assembly onto a motionless sample. This test method does not address any effects or contributions of exterior packaging assemblies.  
1.2 The data acquired may be used for a single point or for use in developing a dynamic cushion curve for the specific material being tested. Such data may be used for comparison among different materials at specific input conditions, or qualifying materials against performance specifications. Caution should be used when attempting to compare data from different methods or when using such data for predicting in-package performance. Depending upon the particular materials of concern, correlation of such data (from among differing procedures or for predicting in–package performance) may be highly variable.
Note 1: Alternative and related method for possible consideration is Test Method D4168.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3950-23(Specification)
Standard Specification for Strapping, Nonmetallic (and Joining Methods)

ABSTRACT
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading. The strappings are classified into five types according to the type of materials used. If necessary, seals and buckles made from steel with zinc, black iron oxide, or any equivalent corrosion protective coatings or plastic buckles may be used. Each sample should be collected and tested using the given procedures and should conform to the required values of breaking strength and elongation, transverse strength, and joint strength, when applicable, for each strapping type.
SCOPE
1.1 This specification covers nonmetallic strapping and joining methods intended for use in closing, reinforcing, and bundling articles for shipment, unitizing, palletizing, and bracing for car loading and truck loading.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM D8410-22(Specification)
Standard Specification for Evaluation of Cellulosic-Fiber-Based Packaging Materials and Products for Compostability in Municipal or Industrial Aerobic Composting Facilities

SCOPE
1.1 This specification covers cellulosic-fiber-based packaging materials and products associated with food, landscape waste, and other compost feedstocks, which are intended to be composted under aerobic conditions in municipal and industrial composting facilities, where thermophilic temperatures are achieved.  
1.2 This specification covers cellulosic-based uncoated and coated packaging materials and products and covers whole packaging products. Products covered in this specification include cellulosic fiber-based products produced from cellulosic pulp, corrugated materials, containerboard, paper, paperboard, and molded fiber.  
1.3 This specification excludes end items where thermoplastic polymer is laminated or extruded to cellulosic substrates.  
1.4 This specification is intended to establish the requirements for labeling cellulosic-fiber-based packaging materials and products as “compostable in aerobic municipal and industrial composting facilities” in accordance with the guidelines issued by the Federal Trade Commission,2 provided the label includes proper qualifications as to the availability of such facilities.  
1.5 The properties in this specification are those required to determine if packaging materials and products will compost satisfactorily in large-scale aerobic municipal or industrial composting where maximum throughput is a high priority and where intermediate stages of biodegradation must not be apparent to the end user for aesthetic reasons.  
1.6 This specification is technically equivalent to ISO 18606.1.7.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4675-14a(2022)(Guide)
Standard Guide for Selection and Use of Flat Strapping Materials1

SIGNIFICANCE AND USE
4.1 This guide is intended to assist the user in selecting strapping material(s) and application method(s) for evaluation when subjected to handling, transit, and storage tests. It describes general load, unit and package types, strapping properties, strapping performance, weight considerations, shear planes, component frictional characteristics, and geometry.
SCOPE
1.1 This guide1 covers information on flat strapping materials (steel and nonmetallic) for the prospective user wanting initial guidance in selecting a strapping material and information on suggested application methods for use in packaging (closing, reinforcing, baling, bundling, unitizing, or palletizing), and loading applications (load unitization and securement to transport vehicle). The use applies to handling, securement, storage, and distribution systems.  
1.2 Carrier associations have established certain packaging and loading requirements that (in some cases) specify the type of strap, the minimum size or strength, the type of joint or seal, and the number of straps, seals, and joints that must be used for particular types of shipments or under certain conditions. Users should consult with their carriers initially to determine if there are applicable published requirements. Individual carriers may establish their own requirements. (See 2.2.)  
1.3 Limitations—This guide is not intended to give specific information as to how strapping must be used in any particular packaging or loading situation. Rather, it is intended to be informational in nature and is offered as a starting point for the testing of strapping being considered by the user. Thorough user testing is essential, as is a review of pertinent regulations that can influence strap selection (size and type), and application methods.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    20 pages
    English language
    sale 15% off
ASTM
ASTM D3953-15(2022)(Specification)
Standard Specification for Strapping, Flat Steel and Seals

ABSTRACT
This specification covers flat steel strapping and seals intended for use in closing, reinforcing, bundling articles for shipment, unitizing, palletizing, and bracing for carloading, truckloading, lifting, and lashing. This specification does not include specialty-type strapping as developed for special applications or strapping produced from alloy metals. Strapping shall be of the following types: Type 1 and Type II; shall be of the following finish: Finish A, Finish B including Grade 1, Grade 2, and Grade 3, Finish C and Finish D; and shall have the prescribed widths and thicknesses in accordance with the specified sizes. Seals shall be of the following classes: Class R and Class H; finishes: Finish A, Finish B including Grade 1, Grade 2, and Grade 3, Finish C, and Finish D; and styles: Style I, Style II, Style III, Style IV, and Style V. Materials shall be cold-rolled carbon steel of the prescribed quality. Strapping and seal shall conform to the physical and mechanical property requirements prescribed for: (1) breaking strength, elongation and seal joint strength, (2) lubrication (by lubricity and edge tests), (3) weld efficiency, (4) seal width, (5) seal application, (6) notch, crimp, and sealless joints, (7) galvanized strapping (by weight loss test), (8) ductility of strapping coating, (9) base metal ductility (by bending test), and (10) straightness (camber, coil set, and spiral twist). The coil configuration are specified and illustrated. Sampling and packaging requirements such as wrapping and packing are also detailed.
SCOPE
1.1 This specification covers flat steel strapping and seals intended for use in closing, reinforcing, bundling articles for shipment, unitizing, palletizing, and bracing for carloading, truckloading, lifting, and lashing.  
1.2 This specification includes strapping and seals made from carbon steel and applies only to the types and sizes as cataloged by strapping suppliers to be a standard, commercially available product. It does not include “specialty”-type strapping as developed for special applications or strapping produced from alloy metals.  
1.3 The values stated in inch-pound units are to be regarded as standard.  
1.4 Performance characteristics may be negatively affected by extremes of temperatures, such as occur during the annealing of steel.  
1.5 The following safety hazards caveat applies only to the test method portion, Sections 11, 12, and 13, of this specification:  
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    14 pages
    English language
    sale 15% off
ASTM
ASTM D4279-95(2022)(Test Method)
Standard Test Methods for Water Vapor Transmission of Shipping Containers—Constant and Cycle Methods

SIGNIFICANCE AND USE
4.1 These test methods are normally used for the following purposes:  
4.1.1 To evaluate materials and constructions for a specific type of container,  
4.1.2 To compare performance of different types of containers,  
4.1.3 To determine adequacy of protection for a specific product or application, and  
4.1.4 To maintain quality control.
SCOPE
1.1 These test methods cover the determination of water vapor transmission rates for bulk shipping containers, as follows:  
1.1.1 Method A, for Reclosable Containers, and  
1.1.2 Method B, for Containers Not Designed for Reclosing.  
1.2 Within each procedure details are given for the constant and cycle methods of test atmosphere.  
1.3 The test may be applied to the container as packed, or after one or more performance tests such as drum (Method D782), vibration (Methods D999), drop (Test Method D5276), impact resistance (Test Methods D880, D4003, and D5277), or performance tests (Practice D4169), as required.  
1.4 For small shipping containers requiring greater accuracy in weighing, the water vapor transmission may be determined in accordance with Test Method D895 or Test Method D1251.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5168-22(Practice)
Standard Practice for Fabrication and Closure of Triple-Wall Corrugated Fiberboard Containers

SIGNIFICANCE AND USE
4.1 Triple-wall corrugated fiberboard containers are used to unitize products into containers of size and shape suitable for manual or mechanical handling and to protect the contents against environmental, handling, shipping, and storage conditions.  
4.2 This practice is intended to cover some of the basic constructions and styles of commercially available triple-wall fiberboard packaging used to unitize and protect contents.
SCOPE
1.1 This practice covers the fabrication and closure of new triple-wall corrugated fiberboard containers.  
1.2 This practice indicates the factors and components that must be controlled in the manufacture of triple-wall fiberboard containers.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off