ASTM B750-08
(Specification)Standard Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
Standard Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
ABSTRACT
This specification covers GALFAN, zinc-aluminum-mischmetal (Zn-5Al-MM) alloy (UNS Z38510) in ingot form for remelting for use in the production of hot-dip coatings on steel. The alloys may be made by any approved process and shall be free from dross, slag, or other harmful contamination. The alloys shall conform to the requirements as to chemical composition prescribed for aluminum, cerium and lanthanum, iron, silicon, lead, cadmium, tin, zinc, and other elements. Sampling for chemical analysis of the alloy in standard ingot form shall be done either by drilling, sawing, or melting, and shall meet the requirements specified for selection of portion, sample preparation, and size of sample and storage. Determination of the chemical composition shall be performed by ICP argon plasma spectrometric or other methods. X-ray fluorescence spectrometry may be used for determination of cerium and lanthanum.
SCOPE
1.1 This specification covers GALFAN, zinc-5 % aluminum-mischmetal (Zn-5Al-MM) alloy (UNS Z38510) in ingot form for remelting for use in the production of hot-dip coatings on steel. Alloy composition is specified in Table 1.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
TABLE 1 GALFAN, Zn-5Al-MM Alloy Ingot Chemical
RequirementsA,B,C,D,E ElementUNS Z38510
Composition,% AluminumF4.2–6.2 Cerium + lanthanum, total 0.03–0.10 Iron, max 0.075 Silicon, max0.015 LeadG, max 0.005 CadmiumG, max 0.005 TinG, max 0.002 OthersH, each, max 0.02 OthersH, total, max 0.04 Zinc Remainder
A For purposes of acceptance and rejection, the observed value or calculated value obtained from analysis should be rounded to the nearest unit in the last right-hand place of figures, used in expressing the specified limit, in accordance with the rounding procedure prescribed in Section 3 of Practice E 29.
B By agreement between purchaser and supplier, analysis may be required and limits established for elements or compounds not specified in the table of chemical composition.
C GALFAN, Zn-5Al-MM alloy ingot for hot-dip coatings may contain antimony, copper, and magnesium in amounts of up to 0.002, 0.1, and 0.05 %, respectively. No harmful effects have ever been noted due to the presence of these elements up to these concentrations and, therefore, analyses are not required for these elements.
D Magnesium may be specified by the buyer up to 0.1 % maximum.
E Zirconium and titanium may each be specified by the buyer up to 0.02 % maximum.
F Aluminum may be specified by the buyer up to 12 % maximum.
G Lead and cadmium, and to a lesser extent tin and antimony, are known to cause intergranular corrosion in zinc-aluminum alloys. For this reason it is important to maintain the levels of these elements below the limits specified.
H Except antimony, copper, magnesium, zirconium, and titanium.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B750 – 08
Standard Specification for
1
GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot
2
Form for Hot-Dip Coatings
This standard is issued under the fixed designation B750; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
TABLE 1 GALFAN, Zn-5Al-MM Alloy Ingot Chemical
1. Scope*
A,B,C,D,E
Requirements
1.1 This specification covers GALFAN, zinc-5 %
UNS Z38510
3
Element
aluminum-mischmetal (Zn-5Al-MM) alloy (UNS Z38510) in
Composition,%
ingot form for remelting for use in the production of hot-dip
F
Aluminum 4.2–6.2
coatings on steel. Alloy composition is specified in Table 1.
Cerium + lanthanum, total 0.03–0.10
1.2 The values stated in inch-pound units are to be regarded Iron, max 0.075
Silicon, max 0.015
as standard. The values given in parentheses are mathematical
G
Lead , max 0.005
conversions to SI units that are provided for information only G
Cadmium , max 0.005
G
Tin , max 0.002
and are not considered standard.
H
Others , each, max 0.02
1.3 This standard does not purport to address all of the
H
Others , total, max 0.04
safety concerns, if any, associated with its use. It is the
Zinc Remainder
responsibility of the user of this standard to become familiar
A
For purposes of acceptance and rejection, the observed value or calculated
with all hazards including those identified in the appropriate value obtained from analysis should be rounded to the nearest unit in the last
right-hand place of figures, used in expressing the specified limit, in accordance
Material Safety Data Sheet (MSDS) for this product/material
with the rounding procedure prescribed in Section 3 of Practice E29.
B
as provided by the manufacturer, to establish appropriate
By agreement between purchaser and supplier, analysis may be required and
safety and health practices, and determine the applicability of limits established for elements or compounds not specified in the table of chemical
composition.
regulatory limitations prior to use.
C
GALFAN, Zn-5Al-MM alloy ingot for hot-dip coatings may contain antimony,
copper, and magnesium in amounts of up to 0.002, 0.1, and 0.05 %, respectively.
2. Referenced Documents
No harmful effects have ever been noted due to the presence of these elements
4 up to these concentrations and, therefore, analyses are not required for these
2.1 ASTM Standards:
elements.
D
B899 Terminology Relating to Non-ferrous Metals and
Magnesium may be specified by the buyer up to 0.1 % maximum.
E
Alloys Zirconium and titanium may each be specified by the buyer up to 0.02 %
maximum.
E29 Practice for Using Significant Digits in Test Data to
F
Aluminum may be specified by the buyer up to 12 % maximum.
G
Determine Conformance with Specifications
Lead and cadmium, and to a lesser extent tin and antimony, are known to
cause intergranular corrosion in zinc-aluminum alloys. For this reason it is
E47 Test Methods for Chemical Analysis of Zinc Die-
important to maintain the levels of these elements below the limits specified.
5
Casting Alloys
H
Except antimony, copper, magnesium, zirconium, and titanium.
E88 Practice for Sampling Nonferrous Metals andAlloys in
Cast Form for Determination of Chemical Composition
E527 Practice for Numbering Metals and Alloys in the
Unified Numbering System (UNS)
E1277 Test Method for Chemical Analysis of Zinc-5 %
1
GALFAN is a registered trademark of the GALFAN Information Center, Inc.
2 Aluminum-MischmetalAlloysbyICPEmissionSpectrom-
This specification is under the jurisdiction of ASTM Committee B02 on
etry
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
6
B02.04 on Zinc and Cadmium.
2.2 Other Standard:
Current edition approved Nov. 1, 2008. Published December 2008. Originally
GF-1 Standard Practice for Determination of Cerium and
approved in 1985. Last previous edition approved in 2007 as B750 – 07. DOI:
Lanthanum Compositions in GALFAN Alloy (5 %
10.1520/B0750-08.
3
UNS number in conformance with Practice E527. -0.04 % La-0.04 % Ce-Bal SHG Zn)
4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6
Standards volume information, refer to the standard’s Document Summary page on Available from International Lead Zinc Research Organization, 2525 Meridian
the ASTM website. Parkway, P.O. Box 12036, Research Triangle Park, NC 27709 – 2036, http://
5
Withdrawn. www.ilzro.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B750–07 Designation: B 750 – 08
Standard Specification for
1
GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot
2
Form for Hot-Dip Coatings
This standard is issued under the fixed designation B 750; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
3
1.1 This specification covers GALFAN, zinc-5 % aluminum-mischmetal (Zn-5Al-MM) alloy (UNS Z38510) in ingot form for
remelting for use in the production of hot-dip coatings on steel. Alloy composition is specified in Table 1.
1.2The values stated in inch-pound units are to be regarded as the standard. The values stated in parentheses are for information
only.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
4
2.1 ASTM Standards:
B 899 Terminology Relating to Non-ferrous Metals and Alloys
E 29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
5
E 47 Test Methods for Chemical Analysis of Zinc Die-Casting Alloys
E 88 Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition
E 527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E 1277 Test Method for Chemical Analysis of Zinc-5 % Aluminum-Mischmetal Alloys by ICP Emission Spectrometry
6
2.2 Other Standard:
GF-1Standard Practice for Determination of Cerium and Lanthanum Compositions in GALFAN Alloy (5% -0.04% La-0.04%
Ce-Bal SHG Zn) Standard Practice for Determination of Cerium and Lanthanum Compositions in GALFAN Alloy (5 %
-0.04 % La-0.04 % Ce-Bal SHG Zn)
1
GALFAN is a registered trademark of the GALFAN Information Center, Inc.
2
This specification is under the jurisdiction ofASTM Committee B02 on Nonferrous Metals andAlloys and is the direct responsibility of Subcommittee B02.04 on Zinc
and Cadmium.
Current edition approved MayNov. 1, 2007.2008. Published May 2007.December 2008. Originally approved in 1985. Last previous edition approved in 20032007 as
B 750 – 037.
3
UNS number in conformance with Practice E 527.
4
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
5
Withdrawn.
6
Available from International Lead Zinc Research Organization, 2525 Meridian Parkway, P.O. Box 12036, Research Triangle Park, NC 27709 – 2036, http://
www.ilzro.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B750–08
TABLE 1 GALFAN, Zn-5Al-MM Alloy Ingot Chemical
A ,B,C,D,E
Requirements
UNS Z38510
Element
Composition,%
F
Aluminum 4.2–6.2
Cerium + lanthanum, total 0.03–0.10
Iron, max 0.075
Silicon, max 0.015
G
Lead , max 0.005
G
Cadmium , max 0.005
G
Tin , max 0.002
H
Others , each, max 0.02
H
Others , total, max 0.04
Zinc Remainder
A
For purposes of acceptance and rejection, the observed value or calculated
value obtained from analysis should be rounded to the nearest unit in the last
right-hand place of figures, used in expressing the specified limit, in accordance
with the rounding procedure prescribed in Section 3 of Practice E 29.
B
By agreement between purchaser and supplier, analysis may be required and
limits established for elements or compounds not specified in the table of chemical
composition.
C
GALFAN, Zn-5Al-MM alloy ingot for hot-dip coatings may contain antimony,
copper, and magnesium in amounts of up to 0.002, 0.1, and 0.05 %, respectively.
No harmful effects have ever been noted due
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.