ASTM B584-14

Standard Specification for Copper Alloy Sand Castings for General Applications

ABSTRACT
This specification covers requirements for copper alloy sand castings for general applications. The components part casting may be manufactured in advance and supplied from stock. The castings shall conform to the compositional requirements for named elements specified. Mechanical properties of copper alloys such as tensile strength, yield strength, and elongation shall be determined. The castings shall not be repaired, plugged, welded, or burned in.
SCOPE
1.1 This specification covers requirements for copper alloy sand castings for general applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2 This is a composite specification replacing former documents as shown in Table 1. Note 1—Other copper alloy castings are included in the following ASTM Specifications: B22/B22M, B61, B62, B66, B67, B148, B176, B271/B271M, B369, B427, B505/B505M, B763/B763M, B770, and B806.  
1.2 Component part castings produced to this specification may be manufactured in advance and supplied from stock. In such cases the manufacturer shall maintain a general quality certification of all castings without specific record or date of casting for a specific casting.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

General Information

• Status: Historical
• Publication Date: 31-Mar-2014
• ICS: 77.150.30 - Copper products
• Technical Committee: B05 - Copper and Copper Alloys
• Drafting Committee: B05.05 - Castings and Ingots for Remelting

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B584 −14
Standard Specification for
1
Copper Alloy Sand Castings for General Applications
This standard is issued under the fixed designation B584; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* B67 Specification for Car and Tender Journal Bearings,
Lined
1.1 This specification covers requirements for copper alloy
B148 Specification for Aluminum-Bronze Sand Castings
sand castings for general applications. Nominal compositions
B176 Specification for Copper-Alloy Die Castings
of the alloys defined by this specification are shown in Table
2 B208 Practice for Preparing Tension Test Specimens for
1. This is a composite specification replacing former docu-
Copper Alloy Sand, Permanent Mold, Centrifugal, and
ments as shown in Table 1.
Continuous Castings
NOTE 1—Other copper alloy castings are included in the following
B271/B271M Specification for Copper-BaseAlloy Centrifu-
ASTM Specifications: B22/B22M, B61, B62, B66, B67, B148, B176,
gal Castings
B271/B271M, B369, B427, B505/B505M, B763/B763M, B770, and
B369 Specification for Copper-Nickel Alloy Castings
B806.
B427 Specification for Gear Bronze Alloy Castings
1.2 Component part castings produced to this specification
B505/B505M Specification for Copper Alloy Continuous
may be manufactured in advance and supplied from stock. In
Castings
such cases the manufacturer shall maintain a general quality
B763/B763M Specification for Copper Alloy Sand Castings
certification of all castings without specific record or date of
for Valve Applications
casting for a specific casting.
B770 Specification for Copper-Beryllium Alloy Sand Cast-
1.3 The values stated in inch-pound units are to be regarded
ings for General Applications
as standard. The values given in parentheses are mathematical
B806 Specification for CopperAlloy Permanent Mold Cast-
conversions to SI units that are provided for information only
ings for General Applications
and are not considered standard.
B824 Specification for General Requirements for Copper
Alloy Castings
2. Referenced Documents
B846 Terminology for Copper and Copper Alloys
3
E255 Practice for Sampling Copper and Copper Alloys for
2.1 ASTM Standards:
the Determination of Chemical Composition
B22/B22M Specification for Bronze Castings for Bridges
E527 Practice for Numbering Metals and Alloys in the
and Turntables
B61 Specification for Steam or Valve Bronze Castings Unified Numbering System (UNS)
2.2 ASME Code:
B62 Specification for Composition Bronze or Ounce Metal
4
Castings ASME Boiler and Pressure Vessel Code
B66 Specification for Bronze Castings for Steam Locomo-
3. Terminology
tive Wearing Parts
3.1 Definitions of terms relating to copper alloys can be
found in Terminology B846.
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
and Copper Alloys and is the direct responsibility of Subcommittee B05.05 on
4. General Requirements
Castings and Ingots for Remelting.
4.1 The following sections of Specification B824 form a
Current edition approved April 1, 2014. Published June 2014. Originally
approved in 1973. Last previous edition approved in 2013 as B584 – 13. DOI:
part of this specification. In the event of a conflict between this
10.1520/B0584-14.
specification and Specification B824, the requirements of this
2
The UNS system for copper and copper alloys (see Practice E527) is a simple
specification shall take precedence.
expansion of the former standard designation system accomplished by the addition
of a prefix “C” and a suffix “00”. The suffix can be used to accommodate 4.1.1 Terminology,
composition variations of the base alloy.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from American Society of Mechanical Engineers (ASME), ASME
Standards volume information, refer to the standard’s Document Summary page on International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
the ASTM website. www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B584−14
TABLE 1 Nominal Compositions
Copper
Previous Man-
Alloy Commercial Alum- Anti- Sili- Nio- Bis-
Classification Desig- Copper Tin Lead Zinc Nickel Sulfur Iron ga
UNS Designation inum mony con bium muth
nation nese
No.
1 1
Leaded red brass C83450 . . . . . . 88 2 ⁄2 26 ⁄2 1 .
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B584 − 13 B584 − 14
Standard Specification for
1
Copper Alloy Sand Castings for General Applications
This standard is issued under the fixed designation B584; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers requirements for copper alloy sand castings for general applications. Nominal compositions of the
2
alloys defined by this specification are shown in Table 1. This is a composite specification replacing former documents as shown
in Table 1.
NOTE 1—Other copper alloy castings are included in the following ASTM specifications:Specifications: B22B22/B22M, B61, B62, B66, B67, B148,
B176, B271B271/B271M, B369, B427, B505/B505M, B763B763/B763M, B770, and B806.
1.2 Component part castings produced to this specification may be manufactured in advance and supplied from stock. In such
cases the manufacturer shall maintain a general quality certification of all castings without specific record or date of casting for
a specific casting.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
3
2.1 ASTM Standards:
B22B22/B22M Specification for Bronze Castings for Bridges and Turntables
B61 Specification for Steam or Valve Bronze Castings
B62 Specification for Composition Bronze or Ounce Metal Castings
B66 Specification for Bronze Castings for Steam Locomotive Wearing Parts
B67 Specification for Car and Tender Journal Bearings, Lined
B148 Specification for Aluminum-Bronze Sand Castings
B176 Specification for Copper-Alloy Die Castings
B208 Practice for Preparing Tension Test Specimens for Copper Alloy Sand, Permanent Mold, Centrifugal, and Continuous
Castings
B271B271/B271M Specification for Copper-Base Alloy Centrifugal Castings
B369 Specification for Copper-Nickel Alloy Castings
B427 Specification for Gear Bronze Alloy Castings
B505/B505M Specification for Copper Alloy Continuous Castings
B763B763/B763M Specification for Copper Alloy Sand Castings for Valve Applications
B770 Specification for Copper-Beryllium Alloy Sand Castings for General Applications
B806 Specification for Copper Alloy Permanent Mold Castings for General Applications
B824 Specification for General Requirements for Copper Alloy Castings
B846 Terminology for Copper and Copper Alloys
E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.05 on Castings
and Ingots for Remelting.
Current edition approved April 1, 2013April 1, 2014. Published April 2013June 2014. Originally approved in 1973. Last previous edition approved in 20122013 as
B584 – 12a.B584 – 13. DOI: 10.1520/B0584-13.10.1520/B0584-14.
2
The UNS system for copper and copper alloys (see Practice E527) is a simple expansion of the former standard designation system accomplished by the addition of a
prefix “C” and a suffix “00”. The suffix can be used to accommodate composition variations of the base alloy.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B584 − 14
TABLE 1 Nominal Compositions
Copper
Previous
Alloy Commercial Alum- Man- Sili- Nio- Bis-
Classification Designation Copper Tin Lead Zinc Nickel Iron
UNS Designation inum ganese con bium muth
No.
1 1
Leaded red brass C83450 . . . . . . 88 2 ⁄2 2 6 ⁄2 1 . . . . . . . . . . . . . . . . . .
C83600 B145-4A 85-5-5-5 or No. 1 com- 85 5 5 5 . . . . . . . . . . . . . . . . . . . . .
position
C83800 B145-4B commercial red brass, 83 4 6 7 . . . . . . . . . . . . . . .
...