iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D330-07

(Specification)

Standard Specification for 2-Butoxyethanol

Standard Specification for 2-Butoxyethanol

ABSTRACT
This specification covers the properties and requirements for 2-butoxyethanol. Specimens shall be suitably sampled and tested, and shall meet specified values of the following properties: apparent specific gravity; color (Pt-Co scale); distillation range (initial boiling point and dry point); water content; and acidity (free acid as acetic acid).
SCOPE
1.1 This specification covers 2-butoxyethanol.
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

General Information

Status
Historical
Publication Date
31-May-2007
ICS
71.080.60 - Alcohols. Ethers
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.35 - Solvents, Plasticizers, and Chemical Intermediates
Current Stage
Ref Project

Relations

Replaces
ASTM D330-93(2001) - Standard Specification for 2-Butoxyethanol
Effective Date
01-Jun-2007

Buy Standard

ASTM D330-07 - Standard Specification for 2-ButoxyethanolASTM D330-07 - Standard Specification for 2-Butoxyethanol
PreviousNext
Technical specification
ASTM D330-07 - Standard Specification for 2-Butoxyethanol
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D330 −07
StandardSpecification for
1,2
2-Butoxyethanol
This standard is issued under the fixed designation D330; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* D5386 Test Method for Color of Liquids Using Tristimulus
Colorimetry
1.1 This specification covers 2-butoxyethanol.
E29 Practice for Using Significant Digits in Test Data to
1.2 The following applies to all specified limits in this
Determine Conformance with Specifications
standard; for purposes of determining conformance with this
E300 Practice for Sampling Industrial Chemicals
standard, an observed value or a calculated value shall be
2.2 U.S. Federal Standard:
rounded off “to the nearest unit” in the last right-hand digit
PPP-C-2020 Specification for Packaging of Chemicals,
4
used in expressing the specification limit, in accordance with
Liquid, Dry, and Paste
the rounding-off method of Practice E29.
3. Properties
1.3 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this 3.1 2-Butoxyethanol shall conform to the following require-
standard. ments:
Apparent specific gravity
1.4 For specific hazard information and guidance, see the
20/20°C 0.901 to 0.904
supplier’sMaterialSafetyDataSheetformaterialslistedinthis
or
specification.
25/25°C 0.898 to 0.901
Color, Pt-Co scale, max (Note 1) 15
Distillation range, 760 mm Hg
2. Referenced Documents
Initial boiling point, °C, min 168
3
Dry point, °C, max 173
2.1 ASTM Standards:
Water, weight %, max 0.1
D268 Guide for Sampling and Testing Volatile Solvents and
Acidity (free acid as acetic acid), 0.01 equivalent to 0.093 mg KOH per
Chemical Intermediates for Use in Paint and Related
weight %, max gram of material
________________
Coatings and Material
D1078 Test Method for Distillation Range of Volatile Or-
NOTE 1—Instrumental Pt-Co color determined by Test Method D5386
ganic Liquids has been shown to have no statistically significant difference from Pt-Co
color determined by Test Method D1209. However, it is not known
D1209 Test Method for Color of Clear Liquids (Platinum-
whether 2-butoxyethanol was part of the sample set included in the
Cobalt Scale)
interlaboratory study.
D1364 Test Method for Water in Volatile Solvents (Karl
Fischer Reagent Titration Method)
4. Sampling
D1613 Test Method for Acidity in Volatile Solvents and
4.1 The material shall be sampled in accordance with
Chemical Intermediates Used in Paint, Varnish, Lacquer,
Practice E300.
and Related Products
D4052 Test Method for Density, Relative Density, and API
5. Test Methods
Gravity of Liquids by Digital Density Meter
5.1 The properties enumerated in this specification shall be
determined in accordance with the following ASTM methods:
1
5.1.1 Apparent Specific Gravity—Determine the apparent
This specification is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, andApplications and is the direct responsibility of
specific gravity by any convenient method that is accurate to
Subcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates .
the third decimal place,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D4836-09(2023)(Specification)
Standard Specification for Dipropylene Glycol Monomethyl Ether

ABSTRACT
This specification covers dipropylene glycol monomethyl ether (DPM). Dipropylene glycol monomethyl ether shall conform to the requirements specified for the following: (1) assay content, (2) distillation range defined by the initial boiling point and dry point, (3) apparent specific gravity, (4) platinum-cobalt scale color, (5) water content, and (6) acidity (free acid as acetic acid). The sampling and test methods to determine conformance to the specified properties are given.
SCOPE
1.1 This specification covers dipropylene glycol monomethyl ether (DPM).  
Note 1: Dipropylene glycol monomethyl ether (DPM) is a mixture of isomers, the predominant isomer being 1-(2-methoxy-1-methylethoxy)-2-propanol.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, consult the supplier’s Safety Data Sheet for materials listed in this standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4794-94(2022)e1(Test Method)
Standard Test Method for Determination of Ethoxyl or Hydroxyethoxyl Substitution in Cellulose Ether Products by Gas Chromatography

ABSTRACT
This test method is applicable to the determination of ethoxyl or hydroxyethoxyl substitution in cellulose ether products by a Zeisel gas chromatographic technique. The equipment and materials to be used shall include reagents, gas chromatograph, electronic integrator, column, syringe, reaction vials, caps, heating block, and a cover. The following reagents are as follows: iodoethane, O-xylene, toluene, hydrochloric acid, and colume packing. When a cellulose ether containing ethyl or hydroxyethyl substitutes is allowed to react with hydriodic acid, one mole of iodoethane is liberated for each mole of ethoxyl or hydroxyethoxyl ether substituted on the cellulose chain. The iodoethane is extracted in-situ with o-xylene and quantitated by gas chromatography using an internal standard technique. It is recommended to run duplicate samples.
SCOPE
1.1 This test method is applicable to the determination of ethoxyl or hydroxyethoxyl substitution in cellulose ether products by a Zeisel gas chromatographic technique.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5 and 9.1.8.1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5008-22(Test Method)
Standard Test Method for Ethyl Methyl Pentanol Content and Purity Value of 2-Ethylhexanol By Gas Chromatography

SIGNIFICANCE AND USE
4.1 This test method is used to determine the purity value and ethyl methyl pentanol content of 2-ethylhexanol.
SCOPE
1.1 This test method covers the determination of ethyl methyl pentanol content and purity value of 2-ethylhexanol.  
1.2 Water and acid cannot be determined by this test method and must be determined in accordance with Test Methods D1613 and E203 and those results used to normalize the chromatographic data.  
1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see 6.1.1.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1257-22(Specification)
Standard Specification for High-Gravity Glycerin

ABSTRACT
This specification covers high-gravity glycerin (98.7 weight%, minimum) for use in the manufacture of alkyd and other synthetic resins. The following properties of glycerin shall be determined: color, Pt-Co scale, sulfate ash content(weight%), and acid value.
SCOPE
1.1 This specification covers high-gravity glycerin (98.7 weight %, minimum) for use in the manufacture of alkyd and other synthetic resins.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value, shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1969-22(Specification)
Standard Specification for 2-Ethylhexanol

ABSTRACT
This specification the properties and requirements for regular and monomer grade 2-ethylhexanol. Specimens shall be appropriately sampled and tested to evaluate their conformance to specified values of the following physical and chemical properties: acidity (free acid as acetic acid); apparent specific gravity; assay content; color (Pt-Co scale); carbonyl as 2-ethylhexanal; ethyl methyl pentanol content; sulfuric acid color; and water content.
SCOPE
1.1 This specification covers regular and monomer grade 2-ethylhexanol.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D330-07(2021)(Specification)
Standard Specification for 2-Butoxyethanol

ABSTRACT
This specification covers the properties and requirements for 2-butoxyethanol. Specimens shall be suitably sampled and tested, and shall meet specified values of the following properties: apparent specific gravity; color (Pt-Co scale); distillation range (initial boiling point and dry point); water content; and acidity (free acid as acetic acid).
SCOPE
1.1 This specification covers 2-butoxyethanol.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, see the supplier’s Material Safety Data Sheet for materials listed in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1133-13(2021)(Test Method)
Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents

SIGNIFICANCE AND USE
4.1 The kauri-butanol value is used as a measure of solvent power of hydrocarbon solvents. High kauri-butanol values indicate relatively strong solvency.
SCOPE
1.1 This test method covers the determination of the relative solvent power of hydrocarbon solvents used in paint and lacquer formulations. This test method is suitable for use with solvents having an initial boiling point over 40 °C and a dry point under 300 °C when determined in accordance with the procedures in Note 1.  
Note 1: Test Method D86 is used to determine the initial boiling point and dry point for mineral spirits and similar petroleum solvents. Test Method D1078 is used for pure compounds and narrow boiling range cuts.  
1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 For specific hazard information and guidance, consult the supplier's Material Safety Data Sheet.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3128-07(2021)(Specification)
Standard Specification for 2-Methoxyethanol

ABSTRACT
This specification covers 2-methoxyethanol. 2-methoxyethanol shall conform to the requirements specified for the following: (1) apparent specific gravity, (2) Pt-Co scale color, (3) distillation range defined by the initial boiling point and dry point, (4) water content, and (5) acidity (free acid as acetic acid). The sampling and test methods to determine conformance to the specified properties are given.
SCOPE
1.1 This specification covers 2-methoxyethanol.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.4 For hazard information and guidance, see the supplier’s Material Safety Data Sheet for materials listed in this specification.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D304-11(2019)(Specification)
Standard Specification for n-Butyl Alcohol (Butanol)

ABSTRACT
This specification covers n-butyl alcohol (butanol). The apparent specific gravity, color, distillation range, non-volatile matter, water properties, and acidity shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers n-butyl alcohol (butanol).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheets.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D5164-05(2019)(Specification)
Standard Specification for Propylene Glycol and Dipropylene Glycol

ABSTRACT
This specification covers propylene glycol and dipropylene glycol for use in the preparation of surface coatings. The material properties enumerated, and apparent specific gravity shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers propylene glycol and dipropylene glycol for use in the preparation of surface coatings.  
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheets.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off