iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4710-02

(Specification)

Standard Specification for Acetaldehyde

Standard Specification for Acetaldehyde

SCOPE
1.1 This specification covers acetaldehyde (99 % grade).
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.
1.3 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

General Information

Status
Historical
Publication Date
09-Jul-2002
ICS
71.080.80 - Aldehydes and ketones
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.35 - Solvents, Plasticizers, and Chemical Intermediates
Current Stage
Ref Project

Relations

Replaces
ASTM D4710-93(1999) - Standard Specification for Acetaldehyde
Effective Date
10-Jul-2002
Replaced By
ASTM D4710-07 - Standard Specification for Acetaldehyde
Effective Date
01-Jun-2007

Buy Standard

ASTM D4710-02 - Standard Specification for AcetaldehydeASTM D4710-02 - Standard Specification for Acetaldehyde
PreviousNext
Technical specification
ASTM D4710-02 - Standard Specification for Acetaldehyde
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 4710 – 02
Standard Specification for
1
Acetaldehyde
This standard is issued under the fixed designation D 4710; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope * 3. Properties
1.1 This specification covers acetaldehyde (99 % grade). 3.1 Acetaldehyde shall conform to the following require-
1.2 The following applies to all specified limits in this ments:
standard; for purposes of determining conformance with this
Purity, wt %, min, as acetaldehyde 99
Color, Pt-Co units, max 15
standard, an observed value or a calculated value shall be
Acidity, wt %, max, (free acid as acetic acid) 0.05
rounded off “to the nearest unit” in the last right-hand digit
Nonvolatile matter, wt %, max 0.5
used in expressing the specification limit, in accordance with
4. Sampling
the rounding-off method of Practice E 29.
1.3 For specific hazard information and guidance, see the
4.1 The material shall be sampled in accordance with
supplier’sMaterialSafetyDataSheetformaterialslistedinthis
Practice E 300.
specification.
5. Test Methods
2. Referenced Documents
5.1 The properties enumerated in this specification shall be
2.1 ASTM Standards:
determined in accordance with the following ASTM test
D 1209 Test Method for Color of Clear Liquids (Platinum-
methods:
2
Cobalt Scale)
5.1.1 Purity—Test Method D 2192.
D 1353 Test Method for Nonvolatile Matter in Volatile
5.1.2 Color—Test Method D 1209.
Solvents for Use in Paint, Varnish, Lacquer, and Related
5.1.3 Acidity—Test Method D 2086.
2
Products
5.1.4 Nonvolatile Matter—Determine the nonvolatile mat-
D 2086 Test Method for Acidity in Vinyl Acetate and
terorresidueafterevaporationinaccordancewithTestMethod
2
Acetaldehyde
D 1353 except use an oven temperature of 60 65°F.
2
D 2192 Test Method for Purity of Aldehydes and Ketones
6. Packaging and Package Marking
E 29 Practice for Using Significant Digits in Test Data to
3
Determine Conformance with Specifications
6.1 Package size shall be agreed upon between the pur-
4
E 300 Practice for Sampling Industrial Chemicals
chaser and the supplier.
2.2 U.S. Federal Specification:
6.2 Packaging shall conform to applicable carrier rules and
PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packaging
regulations or when specified shall conform t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3893-03(2023)(Test Method)
Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography

SIGNIFICANCE AND USE
4.1 This procedure is designed to determine the purity of the two ketones, methyl isoamyl ketone and methyl amyl ketone, and to obtain the concentration of their various impurities, several of which are critical in the application of these solvents.
SCOPE
1.1 This test method covers the determination of the purity of methyl amyl ketone and methyl isoamyl ketone. In addition, the method determines total ketones and various impurities which may include acetone, isopropyl alcohol, methyl propyl ketone, methyl isobutyl ketone, methyl butyl ketone, methyl isobutyl carbinol, mesityl oxide, methyl isoamyl ketone, methyl butyl carbinol, methyl amyl ketone, and diisobutyl ketone.  
1.2 Water and acid cannot be determined by this test method. They must be determined by other appropriate ASTM procedures, and the results used to normalize the chromatographic data.  
1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded “off to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 For hazard information and guidance, see the supplier’s Safety Data Sheet.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D1614-09(2023)(Test Method)
Standard Test Method for Alkalinity in Acetone

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of alkalinity in acetone. The results of this measurement can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination in acetone of alkalinity calculated as ammonia (NH3).  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, consult the supplier’s Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2916-09(2023)(Specification)
Standard Specification for Isophorone

ABSTRACT
This specification covers isophorone volatile solvents used in paints, varnishes, lacquers, and related products. Isoprophone should conform to the specified requirements on apparent specific gravity, color, distillation, purity, acidity as acetic acid, and water content.
SCOPE
1.1 This specification covers isophorone2 (98 % grade) for use in paint, varnish, lacquer, and related products.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for materials listed in this specification.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3329-03(2023)(Test Method)
Standard Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of commonly found impurities in commercially available methyl isobutyl ketone. The measurement of these impurities and the results thereof can individually or when totaled and subtracted from 100 (assay) be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of the purity of methyl isobutyl ketone (MIBK) by gas chromatography and in addition provides a means for measuring certain impurities such as methyl isobutyl carbinol which are of interest. Impurities such as water and acidity are measured by other appropriate ASTM procedures and the results are used to normalize the chromatographic value.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the round-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for the materials listed in this test method.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2379-09(2023)(Test Method)
Standard Test Method for Acidity of Formaldehyde Solutions

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of acidity (as formic acid) in formaldehyde solutions. The results of these measurements can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of the acidity of commercially available formaldehyde solutions.  
1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For hazard information and guidance, see the supplier’s Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2378-22(Specification)
Standard Specification for Formaldehyde 50 % Grade Uninhibited and 37 % Grade Inhibited and Uninhibited

ABSTRACT
This specification covers the properties and requirements for 50 % uninhibited formaldehyde and 37 % uninhibited and inhibited formaldehyde. Specimens shall be suitably sampled and tested, and shall meet the specified values of the following properties: apparent specific gravity; formaldehyde content; acidity; color (Pt-Co scale); iron content; methanol content; and appearance.
SCOPE
1.1 This specification covers 50 % uninhibited formaldehyde and 37 % uninhibited and inhibited formaldehyde.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2194-22(Test Method)
Standard Test Method for Concentration of Formaldehyde Solutions

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of formaldehyde content (assay) of formaldehyde solutions. The results of these measurements can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of the formaldehyde content of commercially available formaldehyde solutions ranging in concentration from 36 to 55 weight %.  
1.2 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2087-22(Test Method)
Standard Test Method for Iron in Formaldehyde Solutions

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of iron content of formaldehyde solutions. The results of these measurements can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of the total iron content of formaldehyde solutions.  
1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2086-22(Test Method)
Standard Test Method for Acidity in Vinyl Acetate and Acetaldehyde

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of total acidity in vinyl acetate and acetaldehyde. The results of these measurements can be used for specification acceptance.
SCOPE
1.1 This test method covers the determination of total acidity as acetic acid in refined vinyl acetate and acetaldehyde.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2804-22(Test Method)
Standard Test Method for Purity of Methyl Ethyl Ketone By Gas Chromatography

SIGNIFICANCE AND USE
4.1 This test method provides a measurement of commonly found impurities in commercially available methyl ethyl ketone. The measurement of these impurities and the results thereof can individually or when totaled and subtracted from 100 (assay) be used for specification purposes.
SCOPE
1.1 This test method covers the determination of the purity of methyl ethyl ketone by gas chromatography. Impurities including water, acidity, and nonvolatile matter are measured by appropriate ASTM procedures and the results are used to normalize the chromatographic value.  
1.2 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off