ASTM D6380-03(2009)

Standard Specification for Asphalt Roll Roofing (Organic Felt)

ABSTRACT
This specification covers three classes and three types of asphalt roll roofing in sheet form, in widths agreed upon between the purchaser and the producer/supplier, and composed of asphalt-saturated organic felt coated on both sides with asphalt. Class M and WS rolls are surfaced on the weather (exposed) side with mineral granules, except for any selvage. Class S rolls are surfaced with powdered talc, mica, or other fine mineral matter to prevent sticking. Type classifications (Types II, III, and IV) are grouped based on minimum net mass per unit area of roofing. Roofing shall adhere to physical property requirements such as breaking strength, water permeance and vapor transmission, width, selvage, area, and moisture.
SCOPE
1.1 This specification covers asphalt roofing in sheet form, in widths agreed upon between the purchaser and the producer/supplier, composed of asphalt-saturated organic felt coated on both sides with asphalt. Class M and WS rolls are surfaced on the (exposed) weather side with mineral granules, except for any selvage. Class S rolls are surfaced with powdered talc, mica, or other fine mineral matter to prevent sticking.
1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Dec-2008
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: D08 - Roofing and Waterproofing
• Drafting Committee: D08.02 - Steep Roofing Products and Assemblies

Relations

• Replaces: ASTM D6380-03 - Standard Specification for Asphalt Roll Roofing (Organic Felt)
• Effective Date: 01-Jan-2009
• Replaced By: ASTM D6380/D6380M-03(2013)e1 - Standard Specification for Asphalt Roll Roofing (Organic Felt)
• Effective Date: 01-Jan-2009

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6380 −03(Reapproved 2009)
Standard Specification for
1
Asphalt Roll Roofing (Organic Felt)
This standard is issued under the fixed designation D6380; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D3019 Specification for Lap Cement Used withAsphalt Roll
Roofing, Non-Fibered, Asbestos-Fibered, and Non-
1.1 This specification covers asphalt roofing in sheet form,
Asbestos-Fibered
in widths agreed upon between the purchaser and the producer/
D4977 Test Method for Granule Adhesion to Mineral Sur-
supplier, composed of asphalt-saturated organic felt coated on
faced Roofing by Abrasion
both sides with asphalt. Class M and WS rolls are surfaced on
E96/E96M Test Methods for Water Vapor Transmission of
the (exposed) weather side with mineral granules, except for
Materials
any selvage. Class S rolls are surfaced with powdered talc,
mica, or other fine mineral matter to prevent sticking.
3. Terminology
1.2 The values stated in SI units are to be regarded as the
3.1 Definitions—Refer to Terminology D1079 for defini-
standard. The inch-pound units given in parentheses are for
tions of terms used in this specification.
information only.
4. Classification
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
4.1 Class S (smooth) rolls shall be surfaced with fine
responsibility of the user of this standard to establish appro-
mineral matter to prevent sticking.
priate safety and health practices and determine the applica-
4.1.1 Type III—Minimum net mass per unit area of roofing,
2 2
bility of regulatory limitations prior to use.
2495 g/m (51.1 lb/100 ft ).
4.1.2 Type IV—Minimum net mass per unit area of roofing,
2. Referenced Documents 2 2
1943 g/m (39.8 lb/100 ft ).
2
2.1 ASTM Standards:
4.2 Class M (mineral) rolls shall be surfaced on the weather
D146 Test Methods for Sampling and Testing Bitumen-
side with mineral granules, except for any selvage.
Saturated Felts and Woven Fabrics for Roofing and
4.2.1 Type II—Minimum net mass of granule-surface
Waterproofing
2 2
portion, 3490 g/m (71.5 lb/100 ft ).
D224 Specification for Smooth-SurfacedAsphalt Roll Roof-
4.3 Class WS (wide selvage) rolls shall be surfaced on the
ing (Organic Felt)
weather side with mineral granules for approximately half the
D228 Test Methods for Sampling, Testing, and Analysis of
width.
Asphalt Roll Roofing, Cap Sheets, and Shingles Used in
2
4.3.1 Type III—Minimum net mass per unit area, 1733 g/m
Roofing and Waterproofing
2
(35.5 lb/100 ft ).
D249 Specification for Asphalt Roll Roofing (Organic Felt)
2
4.3.2 Type IV—Minimum net mass per unit area, 2090 g/m
Surfaced with Mineral Granules
2
(42.8 lb/100 ft ).
D371 Specification for Asphalt Roll Roofing (Organic Felt)
Surfaced with Mineral Granules; Wide Selvage
5. Materials and Manufacture
D1079 Terminology Relating to Roofing and Waterproofing
5.1 In the process of manufacture, a single thickness of dry
organic felt shall first be saturated with asphalt. A coating
1
This specification is under the jurisdiction of ASTM Committee D08 on
asphalt, compounded with or without a fine mineral stabilizer
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02
insoluble in water, shall be applied to one or both sides of the
on Prepared Roofings, Shingles and Siding Materials.
sheet. Class S rolls shall be surfaced on one side with a suitable
The materials covered in this standard were previously covered by three separate
roll roofing material standards: Specifications D224, D249, and D371.
material to prevent sticking in the roll. Class M and WS rolls
Current edition approved Jan. 1, 2009. Published January 2009. Originally
shall be covered on the weather side with mineral granules,
approved in 1999. Last previous edition approved in 2003 as D6380 – 03. DOI:
except for any selvage; the reverse side shall be covered with
10.1520/D6380-03R09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or a suitable material to prevent sticking in the roll.
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
5.2 The felt shall be roofing felt primarily composed of
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. organic fibers. The surface of the felt shall be uniformly and
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6380−03 (2009)
1
relatively smooth. Upon splitting or tearing on the bias, the felt mm ( ⁄16 in.) when te
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:D6380–01 Designation: D 6380 – 03 (Reapproved 2009)
Standard Specification for
1
Asphalt Roll Roofing (Organic Felt)
This standard is issued under the fixed designation D 6380; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—Table 1 was editorially corrected in February 2002.
1. Scope
1.1 This specification covers asphalt roofing in sheet form, in widths agreed upon between the purchaser and the
producer/supplier, composed of asphalt-saturated organic felt coated on both sides with asphalt. Class M andWS rolls are surfaced
on the (exposed) weather side with mineral granules, except for any selvage. Class S rolls are surfaced with powdered talc, mica,
or other fine mineral matter to prevent sticking.
1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for
information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing
D 224 Specification for Smooth-Surfaced Asphalt Roll Roofing (Organic Felt)
2
D 228 Test Methods forAsphalt Roll Roofing, Cap Sheets, and Shingles Test Methods for Sampling, Testing, andAnalysis of
Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing
D 249 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules
D 371 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules; Wide Selvage
2
D 1079 Terminology Relating to Roofing, Waterproofing, and Bituminous Materials Terminology Relating to Roofing and
Waterproofing
D 3019 Specification for Lap Cement Used with Asphalt Roll Roofing, Non Fibered, Asbestos Fibered, and Non Abestos
2
Fibered Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, Asbestos-Fibered, and Non-Asbestos-
Fibered
D 4977 Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion
E 96/E 96M Test Methods for Water Vapor Transmission of Materials
3. Terminology
3.1 Definitions— Refer to Terminology D 1079 for definitions of terms used in this specification.
4. Classification
4.1 Class S (smooth) rolls shall be surfaced with fine mineral matter to prevent sticking.
2 2
4.1.1 Type III—Minimum net mass per unit area of roofing, 2495 g/m (51.1 lb/100 ft ).
2 2
4.1.2 Type IV—Minimum net mass per unit area of roofing, 1943 g/m (39.8 lb/100 ft ).
4.2 Class M (mineral) rolls shall be surfaced on the weather side with mineral granules, except for any selvage.
2 2
4.2.1 Type II—Minimum net mass of granule-surface portion, 3490 g/m (71.5 lb/100 ft ).
4.3 ClassWS (wide selvage) rolls shall be surfaced on the weather side with mineral granules for approximately half the width.
1
This specification is under the jurisdiction of ASTM Committee D08 on Roofing, Waterproofing, Roofing and Bituminous MaterialsWaterproofing and is the direct
responsibility of Subcommittee D08.02 on Prepared Roofings, Shingles and Siding Materials.
The materials covered in this standard were previously covered by three separate roll roofing material standards: Specifications D 224, D 249, and D 371.
Current edition approved May 10, 2001. Published August 2001. Originally published as D6380–99. Last previous edition D6380–99.
Current edition approved Jan. 1, 2009. Published January 2009. Originally approved in 1999. Last previous edition approved in 2003 as D 6380 – 03.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 04.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 6380 – 03 (2009)
2 2
4.3.1 Type III—Minimum net mass per unit area, 1733 g/m (35.5 lb/100 ft ).
2 2
4.3.2 Type IV—Minimum net mass per unit area, 2090 g/m (42.8 lb/100 ft ).
5. Materia
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D6380–03 Designation: D 6380 – 03 (Reapproved 2009)
Standard Specification for
1
Asphalt Roll Roofing (Organic Felt)
This standard is issued under the fixed designation D 6380; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers asphalt roofing in sheet form, in widths agreed upon between the purchaser and the
producer/supplier, composed of asphalt-saturated organic felt coated on both sides with asphalt. Class M andWS rolls are surfaced
on the (exposed) weather side with mineral granules, except for any selvage. Class S rolls are surfaced with powdered talc, mica,
or other fine mineral matter to prevent sticking.
1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for
information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing
D 224 Specification for Smooth-Surfaced Asphalt Roll Roofing (Organic Felt)
D 228 Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing
and Waterproofing
D 249 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules
D 371 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules; Wide Selvage
2
D 1079 Terminology Relating to Roofing, Waterproofing, and Bituminous Materials Terminology Relating to Roofing and
Waterproofing
D 3019 Specification for Lap Cement Used with Asphalt Roll Roofing, Non Fibered, Asbestos Fibered, and Non Abestos
2
Fibered Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, Asbestos-Fibered, and Non-Asbestos-
Fibered
D 4977 Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion
E 96/E 96M Test Methods for Water Vapor Transmission of Materials
3. Terminology
3.1 Definitions— Refer to Terminology D 1079 for definitions of terms used in this specification.
4. Classification
4.1 Class S (smooth) rolls shall be surfaced with fine mineral matter to prevent sticking.
2 2
4.1.1 Type III—Minimum net mass per unit area of roofing, 2495 g/m (51.1 lb/100 ft ).
2 2
4.1.2 Type IV—Minimum net mass per unit area of roofing, 1943 g/m (39.8 lb/100 ft ).
4.2 Class M (mineral) rolls shall be surfaced on the weather side with mineral granules, except for any selvage.
2 2
4.2.1 Type II—Minimum net mass of granule-surface portion, 3490 g/m (71.5 lb/100 ft ).
4.3 ClassWS (wide selvage) rolls shall be surfaced on the weather side with mineral granules for approximately half the width.
2 2
4.3.1 Type III—Minimum net mass per unit area, 1733 g/m (35.5 lb/100 ft ).
2 2
4.3.2 Type IV—Minimum net mass per unit area, 2090 g/m (42.8 lb/100 ft ).
1
This specification is under the jurisdiction ofASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02 on Prepared
Roofings, Shingles and Siding Materials.
The materials covered in this standard were previously covered by three separate roll roofing material standards: Specifications D 224, D 249, and D 371.
´1
Current edition approved May 10, 2003. Published June 2003. Originally approved in 1999. Last previous edition approved in 2001 as D6380–01 .
Current edition approved Jan. 1, 2009. Published January 2009. Originally approved in 1999. Last previous edition approved in 2003 as D 6380 – 03.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 04.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 6380 – 03 (2009)
5. Materials and Manufacture
5.1 In the process of manufacture, a single thickness of dry organic felt shall first be saturated with asphalt. A coating asphalt,
com
...