ASTM D6358-11
(Specification)Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ISO Methods
Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ISO Methods
SCOPE
1.1 This classification system covers unfilled, reinforced and filled materials suitable for injection molding and extrusion using ISO methods. The system allows for the use of poly (phenylene sulfide) (PPS) plastic materials that are recycled, reconstituted recycled-regrind, recovered or reprocessed, or both, provided that the requirements as stated in this specification are met. It is the responsibility of the supplier and the buyer of recycled, reconstituted, recycled-regrind, recovered or reprocessed, or both, poly (phenylene sulfide) plastic materials to ensure compliance (see Guide D7209).
1.2 The properties included in this classification are those required to identify the compositions covered. It is possible that other requirements are necessary to identify particular characteristics important to specialized applications. The use of suffixes as shown in Section 5 is one way of specifying these requirements.
1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection needs to be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification.
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—This standard and ISO 28078 address the same subject matter, but differ in technical content.
Note 2—ASTM D4067 for PPS uses ASTM test methods.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6358 −11
Standard Classification System and Basis for Specification for
Poly (Phenylene Sulfide) (PPS) Injection Molding and
1
Extrusion Materials Using ISO Methods
This standard is issued under the fixed designation D6358; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
but differ in technical content.
1. Scope*
NOTE 2—ASTM D4067 for PPS uses ASTM test methods.
1.1 This classification system covers unfilled, reinforced
andfilledmaterialssuitableforinjectionmoldingandextrusion
2. Referenced Documents
using ISO methods. The system allows for the use of poly
2
2.1 ASTM Standards:
(phenylene sulfide) (PPS) plastic materials that are recycled,
D618 Practice for Conditioning Plastics for Testing
reconstituted recycled-regrind, recovered or reprocessed, or
D883 Terminology Relating to Plastics
both, provided that the requirements as stated in this specifi-
D1600 Terminology forAbbreviatedTerms Relating to Plas-
cation are met. It is the responsibility of the supplier and the
tics
buyerofrecycled,reconstituted,recycled-regrind,recoveredor
D3641 Practice for Injection Molding Test Specimens of
reprocessed, or both, poly (phenylene sulfide) plastic materials
Thermoplastic Molding and Extrusion Materials
to ensure compliance (see Guide D7209).
D3892 Practice for Packaging/Packing of Plastics
1.2 The properties included in this classification are those
D4000 Classification System for Specifying Plastic Materi-
required to identify the compositions covered. It is possible
als
that other requirements are necessary to identify particular
D4067 Classification System for and Basis for Specification
characteristicsimportanttospecializedapplications.Theuseof
for Reinforced and Filled Poly(Phenylene Sulfide) (PPS)
suffixes as shown in Section 5 is one way of specifying these
Injection Molding and Extrusion Materials Using ASTM
requirements.
Methods
D7209 Guide for Waste Reduction, Resource Recovery, and
1.3 This classification system and subsequent line callout
Use of Recycled Polymeric Materials and Products
(specification) are intended to provide a means of calling out
E29 Practice for Using Significant Digits in Test Data to
plastic materials used in the fabrication of end items or parts.
Determine Conformance with Specifications
It is not intended for the selection of materials. Material
3
selection needs to be made by those having expertise in the 2.2 IEC and ISO Standards:
plastic field after careful consideration of the design and the
IEC 60112 Recommended Methods for Determining the
performance required of the part, the environment to which it Comparative Tracking Index of Solid Insulation Materials
will be exposed, the fabrication process to be employed, the
IEC 60243 Recommended Methods for Electric Strength of
costsinvolved,andtheinherentpropertiesofthematerialother Solid Insulating Materials at Power Frequencies
than those covered by this classification.
ISO 62 Plastics-Determination of Water Absorption
ISO 178 Plastics—Determination of Flexural Properties of
1.4 The following precautionary caveat pertains only to the
Rigid Plastics
test method portion, Section 11, of this classification system:
ISO 180/1A Plastics—Determination of Izod Impact
This standard does not purport to address all of the safety
Strength of Rigid Materials
concerns, if any, associated with its use. It is the responsibility
ISO 294-1 Plastics—Injection Moulding Test Specimens of
of the user of this standard to establish appropriate safety and
Thermoplastic Materials
health practices and determine the applicability of regulatory
ISO 527 Plastics—Determination of Tensile Properties
limitations prior to use.
ISO 604 Plastics—DeterminationofCompressiveProperties
NOTE 1—This standard and ISO 28078 address the same subject matter,
1 2
ThisclassificationsystemisunderthejurisdictionofASTMCommitteeD20on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Materials (Section D20.15.17). Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Dec. 1, 2011. Published January 2012. Originally the ASTM website.
3
approved in 1998. Last previous edition approved in 2006 as D6358 - 06. DOI: ISO and IEC Selected Standards for the Plastics Industry, 2nd Edition,ASTM,
10.1520/D6358-11. Stock#: ISOPLAS2.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D6358–06
Standard Classification System for Poly (Phenylene Sulfide)
Injection Molding and Extrusion Materials Using ISO
MethodsDesignation: D6358 – 11
Standard Classification System and Basis for Specification for
Poly (Phenylene Sulfide) (PPS) Injection Molding and
1
Extrusion Materials Using ISO Methods
This standard is issued under the fixed designation D6358; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This classification system covers unfilled, reinforced and filled materials suitable for injection molding and extrusion using
ISO methods. The system allows for the use of poly (phenylene sulfide) (PPS) plastic materials that are recycled, reconstituted
recycled-regrind, recovered or reprocessed, or both, provided that the requirements as stated in this specification are met. It is the
responsibility of the supplier and the buyer of recycled, reconstituted, recycled-regrind, recovered or reprocessed, or both, poly
(phenylene sulfide) plastic materials to ensure compliance (see Guide D5033D7209).
1.2 The properties included in this classification are those required to identify the compositions covered. There may be It is
possible that other requirements are necessary to identify particular characteristics important to specialized applications that may
be specified by using the applications.The use of suffixes as givenshown in Section 5 is one way of specifying these requirements.
1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic
materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection
shouldneeds to be made by those having expertise in the plastic field after careful consideration of the design and the performance
required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and
the inherent properties of the material other than those covered by this classification.
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
NOTE1—There is no equivalent ISO standard. 1—This standard and ISO 28078 address the same subject matter, but differ in technical content.
NOTE2—The last priorASTM standard is Specification 2—ASTM D4067 , D5033, which usesASTM test methods. for PPS usesASTM test methods.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D883 Terminology Relating to Plastics D1238Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1600 Terminology for Abbreviated Terms Relating to Plastics
D3641 Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials D3835Test Method
1
This classification system is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic
Materials (Section D20.15.17).
Current edition approved March 15, 2006. Published April 2006. Originally approved in 1998. Last previous edition approved in 1999 as D6358-99. DOI:
10.1520/D6358-06.
Current edition approved Dec. 1, 2011. Published January 2012. Originally approved in 1998. Last previous edition approved in 2006 as D6358 - 06. DOI:
10.1520/D6358-11.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D6358 – 11
for Determina-
tion of Proper-
ties of Poly-
meric Materials
by Means of a
Capillary Rhe-
ometer
D3892 Practice for Packaging/Packing of Plastics
D4000 Classification System for Spec
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.