ASTM D6262-98(2003)

Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)

SCOPE
1.1 This specification covers requirements and methods of test for the material, dimensions, and workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from PAEK.
1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications may be described by using the classification system given in Section 4.
1.3 This specification allows the use of key clad plastics² (see Section 4).
1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1.
1.5 The following precautionary caveat pertains only to the test method portion Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—There is no similar or equivalent ISO standard.

General Information

• Status: Historical
• Publication Date: 09-Mar-2003
• ICS: 83.140.99 - Other rubber and plastics products
• Technical Committee: D20 - Plastics
• Drafting Committee: D20.15 - Thermoplastic Materials

Relations

• Replaces: ASTM D6262-98 - Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)
• Effective Date: 10-Mar-2003
• Replaced By: ASTM D6262-05 - Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) (Withdrawn 2010)
• Effective Date: 01-Jul-2005
• Referred By: ASTM D8033-22 - Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
• Effective Date: 10-Mar-2003

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 6262 – 98 (Reapproved 2003)
Standard Specification for
Extruded, Compression Molded, and Injection Molded Basic
1
Shapes of Poly(aryl ether ketone) (PAEK)
This standard is issued under the fixed designation D 6262; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This specification in intended to be a means of calling out plastic product used in the fabrication of
end items or parts.
3
1. Scope D 618 Practice for Conditioning Plastics for Testing
3
D 638 Test Method for Tensile Properties of Plastics
1.1 This specification covers requirements and methods of
D 790 TestMethodsforFlexuralPropertiesofUnreinforced
test for the material, dimensions, and workmanship, and the
3
and Reinforced Plastics and Electrical Materials
properties of extruded, compression molded, and injection
3
D 883 Terminology Relating to Plastics
molded PAEK sheet, plate, rod, and tubular bar manufactured
3
D 3892 Practice for Packaging/Packing of Plastics
from PAEK.
D 4000 Classification System for Specifying Plastics Mate-
1.2 The properties included in this specification are those
3
rials
required for the compositions covered. Requirements neces-
D 5033 GuidefortheDevelopmentofStandardsRelatingto
sary to identify particular characteristics important to special-
4
the Proper Use of Recycled Plastics
ized applications may be described by using the classification
2.2 ANSI Standards:
system given in Section 4.
2
Z1.4-1993 Sampling Procedures and Tables for Inspection
1.3 This specification allows the use of key clad plastics
5
by Attributes
(see Section 4).
1.4 The values are stated in inch-pound units and are
3. Terminology
regarded as the standard in all property and dimensional tables.
3.1 Definitions:
For reference purposes, SI units are also included in Table 1.
1
3.1.1 plate, n—flat stock ⁄4 in. [6.4 mm], or greater.
1.5 The following precautionary caveat pertains only to the
3.1.2 recycled plastic shape, n—a product made from up to
test method portion Section 11, of this specification. This
100 % recycled plastic.
standard does not purport to address all of the safety concerns,
3.1.3 rod, n—solid cylindrical shape with a minimum di-
if any, associated with its use. It is the responsibility of the user
1
ameter of ⁄8 in. [3.2 mm].
of this standard to establish appropriate safety and health
1
3.1.4 sheet, n—flat stock less than and including ⁄4 in. [6.4
practices and determine the applicability of regulatory limita-
mm] thickness.
tions prior to use.
3.1.5 tubular bar, n—annular shapes with minimum inside
NOTE 1—There is no similar or equivalent ISO standard. 3 1
diameterof ⁄8 in.[3.5mm]andminimumwallthicknessof ⁄16
in. [1.6 mm].
2. Referenced Documents
3.1.6 virgin plastic shape, n—product that is produced from
2.1 ASTM Standards:
100 % plastic resin that has not been subjected to subsequent
D 256 Test Method for Determining the Pendulum Impact
melt processing.
3
Resistance of Notched Specimens of Plastics
3.2 Definitions of Terms Specific to This Standard:
3.2.1 For definitions of other technical terms pertaining to
plastics used in this specification, see Terminology D 883 or
1
This specification is under the jurisdiction of ASTM Committee D20 on
Guide D 5033.
Plastics and is the direct responsibility of Subcommittee D20.20 on Plastic Products
(Section D20.20.02).
Current edition approved March 10, 2003. Published May 2003. Originally
4
approved in 1998. Last previous edition approved in 1998 as D 6262 - 98. Annual Book of ASTM Standards, Vol 08.03.
2 5
As defined in Guide D 5033. Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
3
Annual Book of ASTM Standards, Vol 08.02. 4th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 6262 – 98 (2003)
4. Classification and Material
1 = Unfilled class
1 = General purpose grade product
4.1 Product shape and size as defined in the applicable
purchase order. 4.5.1.2 Example 2—Compression molded natural PAEK
plate.
4.2 This specification covers product extruded as listed in
Table S-PAEK. Products included in the designations reference CELL CALLOUT: S-PAEK0211
Classification D 4000 callout where applicable.
S-PAEK02 = Product made from PAEK in accordance with Table
4.2.1 ThetypeofPAEKextruded,compressionmolded,and
S-PAEK
injection molded product may be categorized by type, grade 1 = Unfilled class
1 = General purpose grade product
and class depending on resin and filler compositions as defined
in Table S-P
...