ASTM F1062-97(2003)
(Test Method)Standard Test Method for Verification of Ski Binding Test Devices
Standard Test Method for Verification of Ski Binding Test Devices
SIGNIFICANCE AND USE
Results obtained by this test method can be used to determine the suitability of specific test device designs in measuring the release moments of ski/boot/binding systems.
This test method provides a means by which manufacturers of test devices and manufacturers of releasable ski bindings can provide compatible instructions to facilities which perform the final inspection of the complete boot/binding/ski system prior to use.
This test method is not appropriate for determining precision between operators.
SCOPE
1.1 This test method defines procedures to determine agreement between a standard apparatus for measuring the release moments of ski bindings and a test device of unspecified design.
1.2 This test method also covers procedures for checking agreement between individual devices of identical but unspecified design, intended for determining the release moments of ski bindings.
1.3 Values expressed in newton meters, newtons, and centimeters are to be regarded as the standard.
1.4 Values expressed in units of torque may be converted to the appropriate force values when devices which indicate force are used.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 1062 – 97 (Reapproved 2003)
Standard Test Method for Verification of
1
Ski Binding Test Devices
This standard is issued under the fixed designation F 1062; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope F 1063 Practice for Functional Inspections andAdjustments
for Alpine Ski/Boot/Binding Systems
1.1 This test method defines procedures to determine agree-
F 1064 Practice for Sampling and Inspection of Complete
ment between a standard apparatus for measuring the release
and Incomplete Alpine Ski/Binding/Boot Systems in
moments of ski bindings and a test device of unspecified
Rental Applications
design.
1.2 This test method also covers procedures for checking
3. Terminology
agreement between individual devices of identical but unspeci-
3.1 Definitions—The terms and abbreviations used in this
fied design, intended for determining the release moments of
document are defined in accordance with Test Method F 504,
ski bindings.
Specification F 1061, Practice E 456, MethodsE4andE74.
1.3 Values expressed in newton meters, newtons, and cen-
3.2 Definitions of Terms Specific to This Standard:
timeters are to be regarded as the standard.
3.2.1 a—difference between the calibration of the specific
1.4 Values expressed in units of torque may be converted to
device tested for agreement with an instrument of the type
the appropriate force values when devices which indicate force
described in Test Method F 504 and the calibration of an
are used.
individual device of the same design.
1.5 This standard does not purport to address all of the
3.2.2 d—agreement between the test device and the stan-
safety concerns, if any, associated with its use. It is the
dard apparatus described in Test Method F 504 and Section 9
responsibility of the user of this standard to establish appro-
of this test method.
priate safety and health practices and determine the applica-
3.2.3 r—imprecision of the device tested.
bility of regulatory limitations prior to use.
3.2.4 operating range (OR)—the portion of the full range of
2. Referenced Documents the device which may be employed in accordance with
2 Practices F 1063 and F 1064. OR shall be defined by the user
2.1 ASTM Standards:
in accordance with the Inspection section of Annex 2 of
E4 Practices for Force Verification of Testing Machines
Practices F 1063 and F 1064.
E 29 Practice for Using Significant Digits in Test Data to
3.2.5 recommended operating range (ROR)—the portion of
Determine Conformance With Specifications
the full range of the test device that is in accordance with
E74 Practice for Calibration of Force-Measuring Instru-
Proposed Specification P 193.
ments for Verifying the Force Indication of Testing Ma-
3.2.6 reference binding—a binding or group of bindings
chines
used in the verification of a test device.
E 456 Terminology for Relating to Quality and Statistics
3.2.7 standard apparatus—laboratory equipment including
F 504 Test Method for Measuring Quasi-Static Release
a test frame and instrumentation used as the basis for compari-
Moments of Alpine Ski Bindings
son with the test device.
F 1061 Specification for Ski Binding Test Devices
3.2.8 test device—a machine for determining the release
moments of ski/boot/binding systems.
1
This test method is under the jurisdiction of ASTM Committee F27 on Snow
3.3 Symbols:
Skiing and is the direct responsibility of Subcommittee F27.10 on Binding Test
3.3.1 M —a moment in a horizontal plane as shown in the
z
Procedures.
figure in Test Method F 504, which illustrates terminology
Current edition approved Feb. 10, 2003. Published May 2003. Originally
relating to the boot/ski system.
approved in 1988. Last previous edition approved in 1997 as F 1062 – 97.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.3.2 M —a moment in a vertical plane with the ski as
y
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
shown in the figure in Test Method F 504, which illustrates
Standards volume information, refer to the standard’s Document Summary page on
terminology relating to the boot/ski system.
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 1062 – 97 (2003)
4. Significance and Use 8. Procedure
4.1 Results obtained by this test method can be used to 8.1 Perform five repetitions of the following procedure:
determine the suitability of specific test device designs in 8.1.1 Using the standard apparatus, perform three repeti-
measuring the release m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.