iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM B283/B283M-14a

(Specification)

Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)

Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)

ABSTRACT
This specification establishes the requirements for copper and copper die forgings produced by hot pressing method. The forgings included here are designated with the following Copper or Copper Alloy UNS Nos.: C11000 (copper), C14500 (copper-tellurium alloy), C14700 (copper-sulfur alloy), C36500 (leaded Muntz metal), C37000 (free-cutting Muntz metal), C37700 (forging brass), C46400 (naval brass), C48200 (medium leaded naval brass), C48500 (leaded naval brass), C61900 (aluminum bronze), C62300 (9% aluminum bronze), C63000 and C63200 (aluminum-nickel bronze), C64200 (aluminum-silicon bronze), C64210 (6.7% aluminum-silicon bronze), C65500 (high-silicon bronze), C67500 (manganese bronze), C67600, C69300 (copper-zinc-silicon alloy), C70620 (90% copper-10% nickel alloy), C71520 (70% copper-30% nickel alloy), and C77400 (45% nickel-10% silver alloy). The materials for manufacture shall be rods, billets, or blanks of such purity and soundness as to be suitable for processing by hot pressing. Products shall be tested to examine their conformance to mechanical (tensile and yield strengths, and elongation), dimensional, and chemical composition requirements.
SCOPE
1.1 This specification establishes the requirements for copper and copper alloy die forgings produced by the hot pressing method. The following copper and copper alloys are included:    
Copper or Copper Alloy  
UNS No.  
Name    
C11000  
copper    
C14500  
copper-tellurium    
C14700  
copper-sulfur    
C27450  
plumbing brass  
C27451  
plumbing brass  
C27453  
copper zinc alloy  
C35330  
leaded brass  
C36500  
leaded Muntz metal  
C37000  
free-cutting Muntz metal  
C37700  
forging brass  
C46400  
naval brass  
C46750  
tin brass  
C48200  
medium leaded naval brass  
C48500  
leaded naval brass  
C48600  
naval brass  
C49250  
copper-zinc-bismuth alloy  
C49255  
copper-zinc-bismuth-nickel alloy  
C49260  
copper-zinc-bismuth alloy  
C49300  
copper-zinc-tin-bismuth alloy  
C49340  
copper-zinc-tin-bismuth alloy  
C49350  
copper-zinc-tin-bismuth alloy  
C49355  
bismuth brass  
C61900  
aluminum bronze  
C62300  
aluminum bronze, 9 %  
C63000  
aluminum-nickel bronze  
C63200  
aluminum-nickel bronze  
C64200  
aluminum-silicon bronze  
C64210  
aluminum-silicon bronze, 6.7 %  
C65500  
high-silicon bronze (A)  
C67500  
manganese bronze (A)  
C67600  
. . .    
C69300  
copper-zinc-silicon    
C70620  
copper-nickel 90-10  
C71520  
copper-nickel 70-30  
C77400  
nickel silver, 45-10  
C87700  
silicon bronze  
C87710  
silicon bronze  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: Nominal composition and relative forgeability ratings are given in Appendix X1. Copper-nickel alloys C70620 and C71520 are intended for welded applications with seawater exposure.
Note 2: Wrought product intended for hot forging is described in Specification B124/B124M.  
1.3 The following safety caveat pertains only to Section 10 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Aug-2014
ICS
77.150.30 - Copper products
Technical Committee
B05 - Copper and Copper Alloys
Drafting Committee
B05.02 - Rod, Bar, Wire, Shapes and Forgings
Current Stage
Ref Project

Relations

Replaces
ASTM B283/B283M-14 - Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
Effective Date
01-Sep-2014
Replaced By
ASTM B283/B283M-16 - Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
Effective Date
01-Apr-2016
Referred By
ASTM B124/B124M-20 - Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
Effective Date
01-Sep-2014
Referred By
ASTM F1807-23 - Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
Effective Date
01-Sep-2014
Referred By
ASTM F2854-21 - Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing
Effective Date
01-Sep-2014
Referred By
ASTM F1974-23 - Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
Effective Date
01-Sep-2014
Referred By
ASTM F1960-23b - Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
Effective Date
01-Sep-2014
Referred By
ASTM F3347-23 - Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
Effective Date
01-Sep-2014
Referred By
ASTM B249/B249M-22 - Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
Effective Date
01-Sep-2014
Referred By
ASTM F2080-23 - Standard Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe and SDR9 Polyethylene of Raised Temperature (PE-RT) Pipe
Effective Date
01-Sep-2014

Buy Standard

ASTM B283/B283M-14a - Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)ASTM B283/B283M-14a - Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
PreviousNext
Technical specification
ASTM B283/B283M-14a - Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM B283/B283M-14a - Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)REDLINE ASTM B283/B283M-14a - Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
PreviousNext
Technical specification
REDLINE ASTM B283/B283M-14a - Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B283/B283M −14a
StandardSpecification for
1
Copper and Copper-Alloy Die Forgings (Hot-Pressed)
This standard is issued under the fixed designation B283/B283M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
C87700 silicon bronze
C87710 silicon bronze
1.1 This specification establishes the requirements for cop-
1.2 Units—The values stated in either SI units or inch-
per and copper alloy die forgings produced by the hot pressing
pound units are to be regarded separately as standard. The
method. The following copper and copper alloys are included:
values stated in each system may not be exact equivalents;
therefore,eachsystemshallbeusedindependentlyoftheother.
Copper or Copper Alloy
Combining values from the two systems may result in non-
UNS No. Name
conformance with the standard.
C11000 copper
NOTE 1—Nominal composition and relative forgeability ratings are
C14500 copper-tellurium
given in Appendix X1. Copper-nickel alloys C70620 and C71520 are
C14700 copper-sulfur
intended for welded applications with seawater exposure.
C27450 plumbing brass
NOTE 2—Wrought product intended for hot forging is described in
C27451 plumbing brass
Specification B124/B124M.
C27453 copper zinc alloy
C35330 leaded brass
1.3 The following safety caveat pertains only to Section 10
C36500 leaded Muntz metal
of this specification. This standard does not purport to address
C37000 free-cutting Muntz metal
all of the safety concerns, if any, associated with its use. It is
C37700 forging brass
C46400 naval brass
the responsibility of the user of this standard to establish
C46750 tin brass
appropriate safety and health practices and determine the
C48200 medium leaded naval brass
C48500 leaded naval brass applicability of regulatory limitations prior to use.
C48600 naval brass
C49250 copper-zinc-bismuth alloy
2. Referenced Documents
C49255 copper-zinc-bismuth-nickel alloy
2
C49260 copper-zinc-bismuth alloy 2.1 ASTM Standards:
C49300 copper-zinc-tin-bismuth alloy
B124/B124M Specification for Copper and Copper Alloy
C49340 copper-zinc-tin-bismuth alloy
Forging Rod, Bar, and Shapes
C49350 copper-zinc-tin-bismuth alloy
C49355 bismuth brass B249/B249M Specification for General Requirements for
C61900 aluminum bronze
Wrought Copper and Copper-Alloy Rod, Bar, Shapes and
C62300 aluminum bronze, 9 %
Forgings
C63000 aluminum-nickel bronze
C63200 aluminum-nickel bronze
B846 Terminology for Copper and Copper Alloys
C64200 aluminum-silicon bronze
E8/E8M Test Methods for Tension Testing of Metallic Ma-
C64210 aluminum-silicon bronze, 6.7 %
terials
C65500 high-silicon bronze (A)
C67500 manganese bronze (A)
E62 Test Methods for Chemical Analysis of Copper and
3
C67600 . . .
CopperAlloys (Photometric Methods) (Withdrawn 2010)
C69300 copper-zinc-silicon
E75 Test Methods for Chemical Analysis of Copper-Nickel
C70620 copper-nickel 90-10
3
C71520 copper-nickel 70-30 and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
C77400 nickel silver, 45-10
E478 Test Methods for ChemicalAnalysis of CopperAlloys
1 2
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper For referenced ASTM standards, visit the ASTM website, www.astm.org, or
and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod, contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Bar, Wire, Shapes and Forgings. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Sept. 1, 2014. Published October 2014. Originally the ASTM website.
3
approved in 1953. Last previous edition approved in 2014 as B283/B283M – 14. The last approved version of this historical standard is referenced on
DOI: 10.1520/B0283_B0283M-14A. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B283/B283M−14a
2.2 Other Standards: 5.1.2 Copper or Copper Alloy UNS No. designation
4
ASME Boiler and Pressure Vessel Code (Scope),
ISO 7602 Determination of Tellurium Content (High
5.1.3 Drawing showing the shape dimensions and toler-
Content)—Flame Atomic Absorption Spectrometric ances (Dimensions and Permissible Variations),
5
Method
5.1.4 Temper (as specified herein),
JIS H 1068:2005 Method for Determination of Bismuth in
5.1.5 Quantity: total weight or number of pieces for each
6
Copper and Copper Alloys (Japanese Industrial Stan-
form, t
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B283/B283M − 14 B283/B283M − 14a
Standard Specification for
1
Copper and Copper-Alloy Die Forgings (Hot-Pressed)
This standard is issued under the fixed designation B283/B283M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification establishes the requirements for copper and copper alloy die forgings produced by the hot pressing
method. The following copper and copper alloys are included:
Copper or Copper Alloy
UNS No. Name
C11000 copper
C14500 copper-tellurium
C14700 copper-sulfur
C27450 plumbing brass
C27451 plumbing brass
C27453 copper zinc alloy
C35330 leaded brass
C36500 leaded Muntz metal
C37000 free-cutting Muntz metal
C37700 forging brass
C46400 naval brass
C46750 tin brass
C48200 medium leaded naval brass
C48500 leaded naval brass
C48600 naval brass
C49250 copper-zinc-bismuth alloy
C49255 copper-zinc-bismuth-nickel alloy
C49260 copper-zinc-bismuth alloy
C49300 copper-zinc-tin-bismuth alloy
C49340 copper-zinc-tin-bismuth alloy
C49350 copper-zinc-tin-bismuth alloy
C49355 bismuth brass
C61900 aluminum bronze
C62300 aluminum bronze, 9 %
C63000 aluminum-nickel bronze
C63200 aluminum-nickel bronze
C64200 aluminum-silicon bronze
C64210 aluminum-silicon bronze, 6.7 %
C65500 high-silicon bronze (A)
C67500 manganese bronze (A)
C67600 . . .
C69300 copper-zinc-silicon
C70620 copper-nickel 90-10
C71520 copper-nickel 70-30
C77400 nickel silver, 45-10
C87700 silicon bronze
C87710 silicon bronze
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod, Bar,
Wire, Shapes and Forgings.
Current edition approved April 1, 2014Sept. 1, 2014. Published May 2014October 2014. Originally approved in 1953. Last previous edition approved in 20122014 as
B283/B283M – 12.B283/B283M – 14. DOI: 10.1520/B0283_B0283M-14.10.1520/B0283_B0283M-14A.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B283/B283M − 14a
NOTE 1—Nominal composition and relative forgeability ratings are given in Appendix X1. Copper-nickel alloys C70620 and C71520 are intended for
welded applications with seawater exposure.
NOTE 2—Wrought product intended for hot forging is described in Specification B124/B124M.
1.3 The following safety caveat pertains only to Section 10 of this specification. This standard does not purport to address all
of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate
safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
B846 Terminology for Copper and Copper Alloys
E8/E8M Test Methods for Tension Testing of Metallic Materials
3
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)
3
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
E478 Test Methods for Chemical Analysis of Copper Alloys
2.2 Other Standards:
4
ASME Boiler and Pressure Vessel Code
5
ISO 7602 Determination of Tellurium Content (High Content)—Flame Atomic Absorption Spectrometric Method
6
JIS H 1068:2005 Method for Determination of Bismuth in Copper and Copper Alloys (Japanese Industrial Standards)
7
2.3 Military Standards:
MIL-STD-792 Identification Marking Requirements for Special Purpose Components
NAVSEA T9074-AS-GIB-010/271 Requirements for Nondestructive Testing Method
3. General Requirements
3
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM B820-23(Test Method)
Standard Test Method for Bend Test for Determining the Formability of Copper and Copper Alloy Strip

SIGNIFICANCE AND USE
5.1 This bend test provides information as to the formability or the ability of copper and copper alloy strip to resist cracking when being formed.  
5.2 This test method can be used as a quality control tool to determine if material will form to a given radius.  
5.3 This test method is also useful in research and development to provide data for use in selecting a spring material that will safely form to the geometry of a given part.  
5.3.1 The forming characteristic of interest is the smallest bend radius that can be formed without cracks or otherwise unacceptable surface conditions (8.4). This radius, R, is the radius of curvature of the nose of the punch used in the test.  
5.3.2 In addition, the difference between the angle of the bend after testing and 90° provides a measure of post-forming springback.  
5.4 The results are suitable for direct application in design and manufacturing, only when all factors such as the geometry of the part, punch and die design, lubrication, stamping speed, and other material properties are known.
SCOPE
1.1 This test method covers the technique of bend testing copper and copper alloy strip samples to determine product formability or the ability to resist cracking when forming a bend around a specific radius. The criterion for failure is the occurrence of cracks on the convex surface of the bend.  
1.2 This bend test is limited to strip from 0.003 in. to and including 0.031 in. (0.076 mm to and including 0.79 mm) thick.  
1.3 The forming or punch radius for the bend test shall be determined by agreement between the manufacturer or supplier and purchaser. This punch radius is typically equal to or greater than the minimum bend radius without failure for the alloy, temper and thickness combination of the strip being tested.  
1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM B36/B36M-23(Specification)
Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar

ABSTRACT
This specification establishes the requirements brass plates, sheets, strips, and rolled bars made from UNS C21000, C22000, C22600, C23000, C24000, C26000, C26800, C27200, or C28000. Plates are generally available only in the hot-rolled temper. The standard tempers of as hot rolled, rolled, annealed, and annealed-to-temper materials are detailed in this specification as well as in other specifications listed herein. This specification also contains information on the required tensile strengths, Rockwell hardness and grain sizes of the materials. The Rockwell hardness test can be used to test for general conformity to the specification requirements for temper, tensile strength and grain size.
SCOPE
1.1 This specification establishes the requirements for brass (copper-zinc alloy) plate, sheet, strip, and rolled bar of the following alloys:    
Copper Alloy
UNS No.  
Type of Metal  
C21000  
Gilding  
C22000  
Commerical Bronze  
C22600  
Jewerly Bronze  
C23000  
Red Brass  
C24000  
Low Brass  
C26000  
Cartridge Brass  
C26800  
Yellow Brass  
C27200  
…  
C28000  
Muntz Metal  
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.  
1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM B763/B763M-23(Specification)
Standard Specification for Copper Alloy Sand Castings for Valve Applications

ABSTRACT
This specification establishes requirements for copper alloy sand castings for valve applications. The castings shall conform to the chemical composition requirements specified. Mechanical properties shall be determined from separately cast test bars, and shall conform with the requirements. Brinell hardness readings shall be taken in the grip end of the tension test bar and shall be made in accordance with the specified requirements.
SCOPE
1.1 This specification covers requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2  
Note 1: This specification does not cover Copper Alloy UNS Nos. C83600, C92200, C96200, and C96400. These alloys are also used in valve applications. They are covered by the following specifications:
C83600: B62  
C92200: B61  
C96200: B369  
C96400: B369  
1.2 The castings produced under this specification are used in products which may be manufactured in advance and supplied for sale from stock by the manufacturer.  
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B950-23(Guide)
Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys

SIGNIFICANCE AND USE
4.1 The Form and Style for ASTM Standards manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee B05 recognizes the need to provide a supplementary document pertaining to the types of products and materials covered by specifications under its jurisdiction.  
4.2 This guide contains a list of sections to be considered for inclusion in a specification for copper and copper alloys, recommended wording, or both, for such sections. An electronic template including committee adopted language is included in the Appendix.7  
4.3 Persons drafting new product specifications, or modifying existing ones, under the jurisdiction of Committee B05, should follow this guide and the requirements of the Form and Style Manual to ensure consistency.
SCOPE
1.1 This guide covers the editorial procedures and form and style for product specifications under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys.
Note 1: For standards other than product specifications, such as test methods, practices, and guides, see the appropriate sections of Form and Style for ASTM Standards (Blue Book).2  
1.2 This guide has been prepared as a supplement to the current edition of the Form and Style Manual, and is appropriate for use by the subcommittees within ASTM Committee B05 on Copper and Copper Alloys. This guide is to be applied in conjunction with the Form and Style Manual. The Appendix contains a copy of the B05 electronic template which includes adopted language for various sections and provides a template for drafting B05 product specifications.
Note 2: The contents of this guide were previously maintained as a white paper under the title, “ASTM Committee B05 Outline of Form of Specifications.”  
1.3 Subcommittees preparing new product specifications or revising existing ones should follow the practices and procedures outlined herein, and be guided by the latest specifications covering similar commodities.  
1.4 If a conflict exists between this guide and the mandatory sections of the current edition of the Form and Style Manual, the Form and Style Manual requirements have precedence. If a conflict exists between this guide and the nonmandatory sections of the current edition of the Form and Style Manual, this guide has precedence.  
1.5 When patents are involved, the specifications writer should refer to the Form and Style Manual section on patents and trademarks. Also, refer to part F of the Form and Style Manual for trademark information and the safety hazards caveat.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    17 pages
    English language
    sale 15% off
  • Guide
    17 pages
    English language
    sale 15% off
ASTM
ASTM B103/B103M-23(Specification)
Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

ABSTRACT
This specification covers plate, rolled bar, sheet, and strip of copper-tin alloy (phosphor bronze plate), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze). Copper alloys covered include UNS Nos. C51000, C51100, C51180, C51900, C52100, C52180, C52400, C53400, and C54400. Product shall be manufactured by hot or cold working, rolling, and annealing. Chemical composition of the materials shall conform to UNS designation of the material. Product shall conform to chemical analysis, tensile strength and Rockwell hardness tests specified in the specification. Chemical composition testing shall be performed for each element, namely, copper, iron, lead, phosphorus, tin, and zinc. Tension test shall be made so that the longitudinal axis of the specimen is parallel to direction of rolling.
SCOPE
1.1 This specification covers the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar for general application produced from Copper Alloy UNS Nos. C51000, C51100, C51180, C51900, C52100, C52180, C52400, C53400, and C54400. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers.
Note 1: All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.  
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B505/B505M-23(Specification)
Standard Specification for Copper Alloy Continuous Castings

ABSTRACT
This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions. Castings produced to this specification may be manufactured for and supplied from stock. Mechanical tests are required only when specified by the purchaser in the purchase order. Continuous castings shall not be mechanically repaired, plugged, or burned in. Weld repairs may be made at the manufacturer's discretion. For sampling purposes, a lot shall consist of castings of the same composition and same cross-sectional dimensions, produced during the continuous operation of one casting machine, and submitted for inspection at one time unless specified otherwise. The specimen shall be comprised of the following major elements: copper, tin, lead, zinc, iron, aluminum, manganese, and nickel including cobalt. Residual elements may be present in cast copper-base alloys. The fractured bars shall be retained for chemical verification. Both the Brinell hardness reading and Rockwell hardness reading shall be taken on the grip end of the tension test bar. At the request of the purchaser castings shall be marked with the alloy number.
SCOPE
1.1 This specification covers requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1.2  
1.2 Castings produced to this specification may be manufactured for and supplied from stock. In such cases the manufacturer shall maintain heat traceability to specific manufacturing date and chemical analysis.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM B806-23(Specification)
Standard Specification for Copper Alloy Permanent Mold Castings for General Applications

ABSTRACT
This specification covers the requirements for UNS C95300, C95400, C95410, C95500, C95800, C87500, C87800, C87850, and C89540 copper alloy permanent mold castings for general applications. UNS C95800 copper alloy used in sea water applications should be heat treated for better corrosion resistance. In general, alloys included in this specification are weldable. Mechanical properties like the tensile strength, yield strength and elongation are determined from separately cast test bar castings and should conform to the specified requirements.
SCOPE
1.1 This specification covers requirements for copper alloy2 permanent mold castings for general applications. Nominal compositions of the alloys under this specification are shown in Table 1.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B249/B249M-23(Specification)
Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

ABSTRACT
This specification establishes the general requirements common to wrought copper and copper alloy rods, bars, shapes, and forgings. Products shall be manufactured by hot working, cold working, or both, and finished by cold working, annealing, or heat treatment and straightening as identified necessary to meet the properties specified. Materials shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, diameter, length, straightness, and edge contours), mechanical (tensile strength, Rockwell hardness, elongation, and hydrogen embrittlement), electrical resistivity, chemical composition, and grain size requirements. The products shall also meet performance requirements when subjected to residual stress, mercurous nitrate, ammonia vapor, and semiguided bend tests. In the event of conflict between this specification and the individual casting product specifications, the requirements of the casting specification shall take precedence.
SIGNIFICANCE AND USE
12.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.    
Property  
Rounded Unit for Observed or
Calculated Value  
Chemical composition  
Hardness  
nearest unit in the last right-hand  
Electrical resistivity  
significant digit used in expressing the  
Electrical conductivity  
limiting value  
Tensile strength  
nearest ksi [5 MPa]  
Yield strength  
Elongation:  
nearest 1 %  
Grain size:  
Under 0.060 mm  
nearest multiple of 0.005 mm  
0.060 mm and over  
nearest 0.01 mm
SCOPE
1.1 This specification2 covers the general requirements common to wrought copper and copper alloy rod, bar, shapes, and forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M, B140/B140M, B150/B150M, B151/B151M, B187/B187M, B196/B196M, B283/B283M, B301/B301M, B371/B371M, B411/B411M, B441, B453/B453M, B455, B570, B870, B927/B927M, B929, B967/B967M, B974/B974M, and B981/B981M to the extent referenced therein.  
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification are prescribed in the product specification.  
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3.1 Within the text the SI values are given in brackets.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM B927/B927M-23(Specification)
Standard Specification for Brass Rod, Bar, and Shapes

ABSTRACT
This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, and C27400. The material shall be made from cast billets, logs, or rods of copper alloy, as determined by chemical analysis. The products shall be manufactured by such hot working, cold working, and annealing processing as to produce a uniform wrought structure. The material shall conform to the chemical compositional requirements prescribed for copper, lead, iron, and zinc. The standard tempers, either hard or soft anneal (namely: O60, H01, H02, and H04), for rod and bar are specified. Tensile requirements to which the product shall conform includes tensile strength, yield strength, and elongation. The dimensional requirements for rods, bars, and shapes are given.
SCOPE
1.1 This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, C27400, C27450, C27451, C27453, C27550, and C28500.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM B271/B271M-23(Specification)
Standard Specification for Copper-Base Alloy Centrifugal Castings

ABSTRACT
This specification establishes the requirements for copper-based brass or bronze centrifugal castings. Mechanical properties are determined from test bar castings and should meet the requirements listed herein. Brinell hardness readings should be taken on the grip end of tension test bars. All castings should not be repaired by welding without customer approval. UNS C95520 copper alloy castings are used in the heat treated condition only.
SCOPE
1.1 This specification covers requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off