ASTM B30-09
(Specification)Standard Specification for Copper Alloys in Ingot Form
Standard Specification for Copper Alloys in Ingot Form
ABSTRACT
This specification establishes the requirements for copper alloys in ingot form that shall be subjected to remelting for the manufacture of castings having the Copper Alloy UNS No. designations specified and enumerated herein. Any material and manufacturing process may be used so long as the alloy is of the required composition and mechanical characteristics, and the yielded ingot is free of defects of a kind that would render it unsuitable for remelting. Materials shall hence be sampled, prepared, and tested accordingly to examine their conformance to mechanical, chemical composition, and weldability requirements.
SCOPE
1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and Table 2.
1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Designation: B30 – 09a
Standard Specification for
1
Copper Alloys in Ingot Form
This standard is issued under the fixed designation B30; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* Continuous Castings
B271 Specification for Copper-Base Alloy Centrifugal
1.1 This specification establishes the requirements for cop-
Castings
per alloys in ingot form for remelting for the manufacturing of
B369 Specification for Copper-Nickel Alloy Castings
castings having the Copper Alloy UNS No. designation,
B427 Specification for Gear Bronze Alloy Castings
commercial designations and nominal composition shown in
B505/B505M Specification for Copper Alloy Continuous
Table 1 and Table 2.
Castings
1.2 AcrossreferenceofCopperAlloyUNSNos.andcopper
B584 Specification for Copper Alloy Sand Castings for
alloy casting specifications is given in Table 3.
General Applications
1.3 The values stated in inch-pound units are to be regarded
B763 Specification for Copper Alloy Sand Castings for
as standard. No other units of measurement are included in this
Valve Applications
standard.
B770 Specification for Copper-Beryllium Alloy Sand Cast-
2. Referenced Documents
ings for General Applications
B806 SpecificationforCopperAlloyPermanentMoldCast-
2.1 The following documents of the issue in effect on date
ings for General Applications
of material purchase form a part of this specification to the
E8 Test Methods for Tension Testing of Metallic Materials
extent referenced herein:
2
E29 Practice for Using Significant Digits in Test Data to
2.2 ASTM Standards:
Determine Conformance with Specifications
B22 Specification for Bronze Castings for Bridges and
E54 TestMethodsforChemicalAnalysisofSpecialBrasses
Turntables
3
and Bronzes
B61 Specification for Steam or Valve Bronze Castings
E62 Test Methods for Chemical Analysis of Copper and
B62 Specification for Composition Bronze or Ounce Metal
Copper Alloys (Photometric Methods)
Castings
E76 Test Methods for ChemicalAnalysis of Nickel-Copper
B66 Specification for Bronze Castings for Steam Locomo-
3
Alloys
tive Wearing Parts
E255 Practice for Sampling Copper and Copper Alloys for
B67 Specification for Car and Tender Journal Bearings,
the Determination of Chemical Composition
Lined
E478 TestMethodsforChemicalAnalysisofCopperAlloys
B148 Specification for Aluminum-Bronze Sand Castings
E581 Test Methods for Chemical Analysis of Manganese-
B176 Specification for Copper-Alloy Die Castings
Copper Alloys
B194 Specification for Copper-Beryllium Alloy Plate,
Sheet, Strip, and Rolled Bar
3. Ordering Information
B208 Practice for Preparing Tension Test Specimens for
3.1 Orders for ingot should include the following informa-
Copper Alloy Sand, Permanent Mold, Centrifugal, and
tion:
3.1.1 ASTM designation and year of issue (for example,
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
B30 – 05),
and Copper Alloys and is the direct responsibility of Subcommittee B05.05 on
3.1.2 Copper Alloy UNS No. (for example, C83450 and
Castings and Ingots for Remelting.
Table 1, Table 2, Table 4, and Table 5),
Current edition approved Nov. 1, 2009. Published December 2009. Originally
approved in 1919. Last previous edition approved in 2009 as B30 – 09. DOI:
3.1.3 Quantity; total weight, and
10.1520/B0030-09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Withdrawn. The last approved version of this historical standard is referenced
the ASTM website. on www.astm.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B30 – 09a
TABLE 1 Nominal Compositions
Nominal Composition, %
Previously
Copper Alloy
Alloy Name Used Commercial Designation
Alumi- Man- Sili- Nio- Bis-
UNS No.
Copper Tin Lead Zinc Nickel Iron
Designation
num ganese con bium muth
Leaded red brass C83450 . . . 88 2.5 2 6.5 1 . . . . . . . . . . . . . . . . . .
C83600 4A 85-5-5-5 or No. 1 composition 85 5 5 5 . . . . . . . . . . . . . . . . . .
C83800 4B commercial red brass, 83-4-6-7 83 4 6 7 . . . . . . . . . . . . . . . . . . . . .
Leaded semi-red brass C84200 . . . semi-red brass, 80-5-2-13 80 5 2 13 . . . . . . . . . . . . . . . . . . . . .
C84400 5A valve composition 81-3-7-9 81 3 7 9 . . . . . . . . .
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B30–08a Designation: B 30 – 09
Standard Specification for
1
Copper Alloys in Ingot Form
ThisstandardisissuedunderthefixeddesignationB 30;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of
castings having the CopperAlloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and
Table 2.
1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
2. Referenced Documents
2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the extent
referenced herein:
2
2.2 ASTM Standards:
B22 Specification for Bronze Castings for Bridges and Turntables
B61 Specification for Steam or Valve Bronze Castings
B62 Specification for Composition Bronze or Ounce Metal Castings
B66 Specification for Bronze Castings for Steam Locomotive Wearing Parts
B67 Specification for Car and Tender Journal Bearings, Lined
B 148 Specification for Aluminum-Bronze Sand Castings
B 176 Specification for Copper-Alloy Die Castings
B 194 Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
B 208 Practice for Preparing Tension Test Specimens for Copper Alloy Sand, Permanent Mold, Centrifugal, and Continuous
Castings
B 271 Specification for Copper-Base Alloy Centrifugal Castings
B 369 Specification for Copper-Nickel Alloy Castings
B 427 Specification for Gear Bronze Alloy Castings
B 505/B 505M Specification for Copper Alloy Continuous Castings
B 584 Specification for Copper Alloy Sand Castings for General Applications
B 763 Specification for Copper Alloy Sand Castings for Valve Applications
B 770 Specification for Copper-Beryllium Alloy Sand Castings for General Applications
B 806 Specification for Copper Alloy Permanent Mold Castings for General Applications
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E 255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E 478 Test Methods for Chemical Analysis of Copper Alloys
E 581 Test Methods for Chemical Analysis of Manganese-Copper Alloys
1
This specification is under the jurisdiction ofASTM Committee B05 on Copper and CopperAlloys and is the direct responsibility of Subcommittee B05.05 on Castings
and Ingots for Remelting.
Current edition approved Oct.April 1, 2008.2009. Published November 2008.May 2009. Originally approved in 1919. Last previous edition approved in 2008 as
B 30 – 08a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B30–09
TABLE 1 Nominal Compositions
Nominal Composition, %
Previously
Copper Alloy
Alloy Name Used Commercial Designation
Alumi- Man- Sili- Nio- Bis-
UNS No.
Copper Tin Lead Zinc Nickel Iron
Designation
num ganese con bium muth
Leaded red brass C83450 . . . 88 2.5 2 6.5 1 . . . . . . . . . . . . . . . . . .
C83600 4A 85-5-5-5 or No. 1 composition 85 5 5 5 . . . . . . . . . . . . . . . . . .
C83800 4B commercial red brass, 83-4-6-7 83 4 6 7 . . . . . . . . . . . . . . . . . . . . .
Leaded semi-red brass C84200 . . . semi-red brass, 80-5-2-13 80 5 2 13 . . . . . . . . . . . . . . . . . . . . .
C84400 5A valve composition 81-3-7-9 81 3 7 9 . . . . . . . . . . . . . . . . . . . . .
1 1
C84800 5B semi-red brass, 76-2 ⁄2-6 ⁄2-15
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B30–08a Designation: B 30 – 09
Standard Specification for
1
Copper Alloys in Ingot Form
ThisstandardisissuedunderthefixeddesignationB 30;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of
castings having the CopperAlloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and
Table 2.
1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
2. Referenced Documents
2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the extent
referenced herein:
2
2.2 ASTM Standards:
B22 Specification for Bronze Castings for Bridges and Turntables
B61 Specification for Steam or Valve Bronze Castings
B62 Specification for Composition Bronze or Ounce Metal Castings
B66 Specification for Bronze Castings for Steam Locomotive Wearing Parts
B67 Specification for Car and Tender Journal Bearings, Lined
B 148 Specification for Aluminum-Bronze Sand Castings
B 176 Specification for Copper-Alloy Die Castings
B 194 Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
B 208 Practice for Preparing Tension Test Specimens for Copper Alloy Sand, Permanent Mold, Centrifugal, and Continuous
Castings
B 271 Specification for Copper-Base Alloy Centrifugal Castings
B 369 Specification for Copper-Nickel Alloy Castings
B 427 Specification for Gear Bronze Alloy Castings
B 505/B 505M Specification for Copper Alloy Continuous Castings
B 584 Specification for Copper Alloy Sand Castings for General Applications
B 763 Specification for Copper Alloy Sand Castings for Valve Applications
B 770 Specification for Copper-Beryllium Alloy Sand Castings for General Applications
B 806 Specification for Copper Alloy Permanent Mold Castings for General Applications
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E 255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E 478 Test Methods for Chemical Analysis of Copper Alloys
E 581 Test Methods for Chemical Analysis of Manganese-Copper Alloys
1
This specification is under the jurisdiction ofASTM Committee B05 on Copper and CopperAlloys and is the direct responsibility of Subcommittee B05.05 on Castings
and Ingots for Remelting.
Current edition approved Oct.April 1, 2008.2009. Published November 2008.May 2009. Originally approved in 1919. Last previous edition approved in 2008 as
B 30 – 08a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B30–09
TABLE 1 Nominal Compositions
Nominal Composition, %
Previously
Copper Alloy
Alloy Name Used Commercial Designation
Alumi- Man- Sili- Nio- Bis-
UNS No.
Copper Tin Lead Zinc Nickel Iron
Designation
num ganese con bium muth
Leaded red brass C83450 . . . 88 2.5 2 6.5 1 . . . . . . . . . . . . . . . . . .
C83600 4A 85-5-5-5 or No. 1 composition 85 5 5 5 . . . . . . . . . . . . . . . . . .
C83800 4B commercial red brass, 83-4-6-7 83 4 6 7 . . . . . . . . . . . . . . . . . . . . .
Leaded semi-red brass C84200 . . . semi-red brass, 80-5-2-13 80 5 2 13 . . . . . . . . . . . . . . . . . . . . .
C84400 5A valve composition 81-3-7-9 81 3 7 9 . . . . . . . . . . . . . . . . . . . . .
1 1
C84800 5B semi-red brass, 76-2 ⁄2-6 ⁄2-15
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.