ASTM A299/A299M-17
(Specification)Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon
Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon
ABSTRACT
This specification covers manganese-silicon carbon steel plates for use in welded boilers and other pressure vessels. Plates under this specification are produced in two grades. The steel shall be killed and shall conform to the fine austenitic grain size requirement. Tension test shall be made to conform to the requirements specified.
SCOPE
1.1 This specification2 covers manganese-silicon carbon steel plates for use in welded boilers and other pressure vessels.
1.2 Plates under this specification are produced in two grades. The specified minimum yield strength decreases for thicknesses over 1 in. [25 mm].
1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A299/A299M −17
Standard Specification for
1
Pressure Vessel Plates, Carbon Steel, Manganese-Silicon
This standard is issued under the fixed designationA299/A299M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* A20/A20M SpecificationforGeneralRequirementsforSteel
2
Plates for Pressure Vessels
1.1 This specification covers manganese-silicon carbon
A435/A435M Specification for Straight-Beam Ultrasonic
steelplatesforuseinweldedboilersandotherpressurevessels.
Examination of Steel Plates
1.2 Plates under this specification are produced in two
A577/A577M Specification for Ultrasonic Angle-Beam Ex-
grades. The specified minimum yield strength decreases for
amination of Steel Plates
thicknesses over 1 in. [25 mm].
A578/A578M Specification for Straight-Beam Ultrasonic
Examination of Rolled Steel Plates for Special Applica-
1.3 The maximum thickness of plates is limited only by the
capacity of the composition to meet the specified mechanical tions
property requirements.
3. General Requirements and Ordering Information
1.4 For plates produced from coil and furnished without
3.1 Plates supplied to this product specification shall con-
heat treatment or with stress relieving only, the additional
form to Specification A20/A20M, which outlines the testing
requirements,includingadditionaltestingrequirementsandthe
and retesting methods and procedures, permitted variations in
reporting of additional test results, of Specification A20/A20M
dimensions and mass, quality and repair of defects, marking,
apply.
loading, and ordering information.
1.5 The values stated in either inch-pound units or SI units
3.2 In addition to the basic requirements of this
are to be regarded separately as standard. Within the text, the
specification, certain supplementary requirements are available
SI units are shown in brackets. The values stated in each
where additional control, testing, or examination is required to
system are not exact equivalents; therefore, each system must
meet end use requirements. The purchaser is referred to the
be used independently of the other. Combining values from the
listed supplementary requirements in this specification and to
two systems may result in nonconformance with the specifi-
the detailed requirements in Specification A20/A20M.
cation.
3.3 Coils are excluded from qualification to this specifica-
1.6 This international standard was developed in accor-
dance with internationally recognized principles on standard- tion until they are processed into finished plates. Plates
produced from coil means plates that have been cut to
ization established in the Decision on Principles for the
individuallengthsfromcoil.Theprocessordirectlycontrols,or
Development of International Standards, Guides and Recom-
is responsible for, the operations involved in the processing of
mendations issued by the World Trade Organization Technical
coils into finished plates. Such operations include decoiling,
Barriers to Trade (TBT) Committee.
leveling, cutting to length, testing, inspection, conditioning,
heat treatment (if applicable), packaging, marking, loading for
2. Referenced Documents
shipment, and certification.
3
2.1 ASTM Standards:
NOTE 1—For plates produced from coil and furnished without heat
treatment or with stress relieving only, three test results are reported for
each qualifying coil. Additional requirements regarding plates from coil
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
are described in Specification A20/A20M.
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
3.4 If the requirements of this specification are in conflict
A01.11 on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Nov. 1, 2017. Published November 2017. Originally
with the requirements of Specification A20/A20M, the require-
approved in 1947. Last previous edition approved in 2014 as A299/A299M – 09
ments of this specification shall prevail.
(2014). DOI: 10.1520/A0299_A0299M-17.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
4. Materials and Manufacture
cation SA-299/SA-299M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4.1 Steelmaking Practice—The steel shall be killed and
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
shall conform to the fine austenitic grain size requirement of
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Specification A20/A20M.
*A Summary of Changes section appears at the
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A299/A299M − 09 (Reapproved 2014) A299/A299M − 17
Standard Specification for
1
Pressure Vessel Plates, Carbon Steel, Manganese-Silicon
This standard is issued under the fixed designation A299/A299M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
2
1.1 This specification covers manganese-silicon carbon steel plates for use in welded boilers and other pressure vessels.
1.2 Plates under this specification are produced in two grades. The specified minimum yield strength decreases for thicknesses
over 1 in. [25 mm].
1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical
property requirements; however, current practice normally limits the maximum thickness of plates furnished under this
specification to 8 in. [200 mm]. requirements.
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements,
including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
A435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates
A577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates
A578/A578M Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
3. General Requirements and Ordering Information
3.1 Plates supplied to this product specification shall conform to Specification A20/A20M, which outlines the testing and
retesting methods and procedures, permitted variations in dimensions and mass, quality and repair of defects, marking, loading,
and ordering information.
3.2 In addition to the basic requirements of this specification, certain supplementary requirements are available where additional
control, testing, or examination is required to meet end use requirements. The purchaser is referred to the listed supplementary
requirements in this specification and to the detailed requirements in Specification A20/A20M.
3.3 Coils are excluded from qualification to this specification until they are processed into finished plates. Plates produced from
coil means plates that have been cut to individual lengths from coil. The processor directly controls, or is responsible for, the
operations involved in the processing of coils into finished plates. Such operations include decoiling, leveling, cutting to length,
testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and certification.
NOTE 1—For plates produced from coil and furnished without heat treatment or with stress relieving only, three test results are reported for each
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.11
on Steel Plates for Boilers and Pressure Vessels.
Current edition approved March 1, 2014Nov. 1, 2017. Published March 2014November 2017. Originally approved in 1947. Last previous edition approved in 20092014
as A299/A299M – 09.A299/A299M – 09 (2014). DOI: 10.1520/A0299_A0299M-09R14.10.1520/A0299_A0299M-17.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-299/SA-299M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.