ASTM B400/B400M-14
(Specification)Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum 1350 Conductors
Standard Specification for Compact Round Concentric-Lay-Stranded Aluminum 1350 Conductors
ABSTRACT
This specification covers aluminum1350-H19, 1350-H16 or -H26, 1350-H14 or -H24, and 1350-H142 or -H242 bare compact-round concentric-lay-stranded conductors made from round or shaped wires for use as uninsulated electric conductors or in covered or insulated electrical conductors. Joint shall be cold-pressure welded or electric-butt, cold-upset welded. The conductors shall conform to the required construction values of number of wires, nominal compact conductor diameter, nominal cross-sectional area and nominal DC resistance. Tests for the mechanical and electrical properties of wire composing the conductor shall be made before stranding and the conductors shall conform to the required values of breaking strength and rated strength.
SCOPE
1.1 This specification covers aluminum 1350-H19 (extra hard), 1350-H16 or -H26 ([n ]hard), 1350-H14 or -H24 (1/2 hard) and 1350-H142 or -H242 (1/2 hard) bare compact-round concentric-lay-stranded conductors made from round or shaped wires for use as uninsulated electrical conductors or in covered or insulated electrical conductors. These conductors shall be composed of a central core surrounded by one or more roller or die compacted layers of helically applied wires (Explanatory Note 1 and Note 2).
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.Note 1—Prior to 1975, aluminum 1350 was designated as EC aluminum.Note 2—The aluminum and temper designations conform to ANSI Standard H35.1. Aluminum 1350 corresponds to Unified Numbering System A91350 in accordance with Practice E527.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B400/B400M −14
Standard Specification for
Compact Round Concentric-Lay-Stranded Aluminum 1350
1
Conductors
This standard is issued under the fixed designation B400/B400M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope B609/B609M Specification for Aluminum 1350 Round
Wire, Annealed and Intermediate Tempers, for Electrical
1.1 This specification covers aluminum 1350-H19 (extra
Purposes
1
hard), 1350-H16 or -H26 ([n ]hard), 1350-H14 or -H24 ( ⁄2
E29 Practice for Using Significant Digits in Test Data to
1
hard) and 1350-H142 or -H242 ( ⁄2 hard) bare compact-round
Determine Conformance with Specifications
concentric-lay-strandedconductorsmadefromroundorshaped
E527 Practice for Numbering Metals and Alloys in the
wires for use as uninsulated electrical conductors or in covered
Unified Numbering System (UNS)
or insulated electrical conductors. These conductors shall be
2.2 Other Documents:
composedofacentralcoresurroundedbyoneormorerolleror
ANSI H35.1/H35.1(M) Alloy and Temper Designation Sys-
die compacted layers of helically applied wires (Explanatory
3
tems for Aluminum
Note 1 and Note 2).
NBS Handbook 100-Copper Wire Tables, of the National
1.2 The values stated in either SI units or inch-pound units
4
Bureau of Standards
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each
3. Classification
system shall be used independently of the other. Combining
3.1 For the purpose of this specification, conductors are
values from the two systems may result in non-conformance
classified as follows:
with the standard.
3.1.1 Class AA—For bare conductors usually used in over-
NOTE 1—Prior to 1975, aluminum 1350 was designated as EC
head lines.
aluminum.
3.1.2 Class A—For conductors to be covered with weather-
NOTE 2—The aluminum and temper designations conform to ANSI
resistant materials, and for bare conductors where greater
Standard H35.1. Aluminum 1350 corresponds to Unified Numbering
System A91350 in accordance with Practice E527. flexibility than is afforded by ClassAAis required. Conductors
indicatedforfurtherfabricationintotreewireortobeinsulated
2. Referenced Documents
and laid helically with or around aluminum or ACSR
2
messengers, shall be regarded as Class A conductors with
2.1 ASTM Standards:
respect to direction of lay only (see 6.3).
B230/B230M Specification for Aluminum 1350–H19 Wire
3.1.3 Class B—For conductors to be insulated with various
for Electrical Purposes
materials such as rubber, paper, varnished cloth, and so forth,
B231/B231M Specification for Concentric-Lay-Stranded
and for the conductors indicated under Class A where greater
Aluminum 1350 Conductors
flexibility is required.
B263 Test Method for Determination of Cross-Sectional
Area of Stranded Conductors
4. Ordering Information
B354 Terminology Relating to Uninsulated Metallic Electri-
cal Conductors 4.1 Orders for material under this specification shall include
the following information:
4.1.1 Quantity of each size and class (Table 1),
1 4.1.2 Conductor size; circular-mil area orAWG (Section 7),
This specification is under the jurisdiction of ASTM Committee B01 on
Electrical Conductors and is the direct responsibility of Subcommittee B01.07 on 4.1.3 Class (Section 3),
Conductors of Light Metals.
4.1.4 Temper (Section 13),
Current edition approved Jan. 1, 2014. Published January 2014. Originally
ε1
approved in 1963. Last previous edition approved in 2008 as B400/B400M – 08 .
DOI: 10.1520/B0400_B0400M-14.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from National Technical Information Service (NTIS), 5285 Port
the ASTM website. Royal Rd., Springfield, VA 22161, http://www.ntis.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B400/B400M − 14
TABLE 1 Construction of Compact-Round Concentric-Lay-Stranded, Aluminum Conductors
NOTE 1—Metric values listed below represent a soft conversion and as such they may not be the same as those metric values which are calculated from
the basic metric density.
Nominal Compact Nominal DC Resistance
Nominal Nominal Mass
Conductor Size
Number of
Conductor Diameter at 20°C
Class Mass per p
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: B400/B400M − 08 B400/B400M − 14
Standard Specification for
Compact Round Concentric-Lay-Stranded Aluminum 1350
1
Conductors
This standard is issued under the fixed designation B400/B400M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Designation was corrected editorially in October 2013.
1. Scope
1
1.1 This specification covers aluminum 1350-H19 (extra hard), 1350-H16 or -H26 ([n ]hard), 1350-H14 or -H24 ( ⁄2 hard) and
1
1350-H142 or -H242 ( ⁄2 hard) bare compact-round concentric-lay-stranded conductors made from round or shaped wires for use
as uninsulated electrical conductors or in covered or insulated electrical conductors. These conductors shall be composed of a
central core surrounded by one or more roller or die compacted layers of helically applied wires (Explanatory Note 1 and Note
2).
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
NOTE 1—Prior to 1975, aluminum 1350 was designated as EC aluminum.
NOTE 2—The aluminum and temper designations conform to ANSI Standard H35.1. Aluminum 1350 corresponds to Unified Numbering System
A91350 in accordance with Practice E527.
2. Referenced Documents
2
2.1 ASTM Standards:
B230/B230M Specification for Aluminum 1350–H19 Wire for Electrical Purposes
B231/B231M Specification for Concentric-Lay-Stranded Aluminum 1350 Conductors
B263 Test Method for Determination of Cross-Sectional Area of Stranded Conductors
B354 Terminology Relating to Uninsulated Metallic Electrical Conductors
B609/B609M Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
2.2 Other Documents:
3
ANSI H35.1/H35.1(M) Alloy and Temper Designation Systems for Aluminum
4
NBS Handbook 100-Copper Wire Tables, of the National Bureau of Standards
3. Classification
3.1 For the purpose of this specification, conductors are classified as follows:
3.1.1 Class AA—For bare conductors usually used in overhead lines.
3.1.2 Class A—For conductors to be covered with weather-resistant materials, and for bare conductors where greater flexibility
than is afforded by Class AA is required. Conductors indicated for further fabrication into tree wire or to be insulated and laid
helically with or around aluminum or ACSR messengers, shall be regarded as Class A conductors with respect to direction of lay
only (see 6.3).
1
This specification is under the jurisdiction of ASTM Committee B01 on Electrical Conductors and is the direct responsibility of Subcommittee B01.07 on Conductors
of Light Metals.
Current edition approved Sept. 1, 2008Jan. 1, 2014. Published October 2008January 2014. Originally approved in 1963. Last previous edition approved in 20042008 as
ε1
B400 – 04.B400/B400M – 08 . DOI: 10.1520/B0400_B0400M-08E01.10.1520/B0400_B0400M-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Available from National Technical Information Service (NTIS), 5285 Port Royal Rd., Springfield, VA 22161, http://www.ntis.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B400/B400M − 14
3.1.3 Class B—For conductors to be insulated with various materials such as rubber, paper, varnished cloth, and so forth, and
for the conductors indicated under Class A where greater flexibility is required.
4. Ordering Information
4.1 Orders for material under this specification shall include the following information:
4.1.1 Quantity of each size and class (Table 1),
4.1.2 Conductor size; circular-mil area or A
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.