ASTM F409-02(2008)
(Specification)Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings
Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings
ABSTRACT
This specification covers the material, dimensional ,and performance requirements and associated test methods for thermoplastic tubes and fittings for accessible and replaceable domestic waste connections. The tubes, fittings and mechanical joint components shall be made of either virgin acrylonitrile-butadiene-styrene (ABS) plastic, virgin poly(vinyl chloride) (PVC) plastic, or virgin polypropylene plastic. When evaluated by the test procedures provided herein, the products shall adhere to requirements stipulated for hydrostatic pressure, axial stress, joint integrity, and solvent cement.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, hydrostatic pressure, joint integrity, and solvent cement for thermoplastic tube and fittings for accessible and replaceable domestic waste connections. Marking requirements are also included. Plastic which does not meet the material requirements specified in Section 5 is excluded.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F409 −02(Reapproved 2008) An American National Standard
Standard Specification for
Thermoplastic Accessible and Replaceable Plastic Tube and
1
Tubular Fittings
ThisstandardisissuedunderthefixeddesignationF409;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope (CPVC) Compounds
D2122 Test Method for Determining Dimensions of Ther-
1.1 This specification covers requirements and test methods
moplastic Pipe and Fittings
for materials, dimensions and tolerances, hydrostatic pressure,
D2235 Specification for Solvent Cement for Acrylonitrile-
joint integrity, and solvent cement for thermoplastic tube and
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
fittings for accessible and replaceable domestic waste connec-
D2564 Specification for Solvent Cements for Poly(Vinyl
tions. Marking requirements are also included. Plastic which
Chloride) (PVC) Plastic Piping Systems
does not meet the material requirements specified in Section 5
is excluded. D2609 Specification for Plastic Insert Fittings for Polyeth-
ylene (PE) Plastic Pipe
1.2 Thetextofthisspecificationreferencesnotes,footnotes,
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe
and appendixes which provide explanatory material. These
and Fittings
notesandfootnotes(excludingthoseintablesandfigures)shall
D2661 Specification for Acrylonitrile-Butadiene-Styrene
not be considered as requirements of the specification.
(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe
1.3 The values stated in inch-pound units are to be regarded
and Fittings
as standard. The values given in parentheses are mathematical
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic
conversions to SI units that are provided for information only
Drain, Waste, and Vent Pipe and Fittings
and are not considered standard.
D3965 ClassificationSystemandBasisforSpecificationsfor
1.4 The following safety hazards caveat pertains only to the
Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials
test methods portion, Section 8, of this specification: This
for Pipe and Fittings
standard does not purport to address all of the safety concerns,
D4101 Specification for Polypropylene Injection and Extru-
if any, associated with its use. It is the responsibility of the user
sion Materials
of this standard to establish appropriate safety and health
F402 Practice for Safe Handling of Solvent Cements,
practices and determine the applicability of regulatory limita-
Primers, and Cleaners Used for Joining Thermoplastic
tions prior to use.
Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
2. Referenced Documents
F1498 Specification forTaper PipeThreads 60° forThermo-
2
2.1 ASTM Standards:
plastic Pipe and Fittings
D618 Practice for Conditioning Plastics for Testing
2.2 Federal Standard:
D1600 TerminologyforAbbreviatedTermsRelatingtoPlas-
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
tics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
2.3 Military Standard:
3
Compounds and Chlorinated Poly(Vinyl Chloride)
MIL-STD-129 Marking for Shipment and Storage
2.4 ANSI/ASME Standard:
4
B1.20.1 Pipe Threads, General Purpose (Inch)
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Nov. 1, 2008. Published February 2009. Originally
approved in 1975. Last previous edition approved in 2002 as F409 – 02. DOI:
3
10.1520/F0409-02R08. Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.dodssp.daps.mil.
4
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F409−02 (2008)
TABLE 1 Dimensions and Tolerances for Outside Diameters and Thickness of Plastic Tube
Outside Diameter Wall Thickness
Nominal Tube Size Average Tolerance on Average Out-of-Roundness Minimum
(maximum minus minimum)
in. in. (mm) in. (mm) in. (mm) in. (mm)
1
1 ⁄4 1.250 (31.75) ±0.005 (±0.127) 0.020 (0.51) 0.062 (1.575)
1
1 ⁄2 1.500 (38.10) ±0.005
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F409–02 Designation: F 409 – 02 (Reapproved 2008)
Standard Specification for
Thermoplastic Accessible and Replaceable Plastic Tube and
1
Tubular Fittings
This standard is issued under the fixed designation F 409; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, hydrostatic pressure, joint
integrity, and solvent cement for thermoplastic tube and fittings for accessible and replaceable domestic waste connections.
Marking requirements are also included. Plastic which does not meet the material requirements specified in Section 5 is excluded.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 618 Practice for Conditioning Plastics for Testing
D 1600 Terminology for Abbreviated Terms Relating to Plastics
D 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D 2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D 2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D 2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D 2609 Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
D 2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
D 2661 Specification forAcrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
D 2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D 3965 Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) CompoundsMaterials for Pipe and Fittings
D 4101 Specification for Propylene Plastic Polypropylene Injection and Extrusion Materials
F 402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F 412 Terminology Relating to Plastic Piping Systems
F 1498 Specification for Taper Pipe Thread 60°Threads 60 for Thermoplastic Pipe and Fittings
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.3 Military Standard:
3
MIL-STD-129 Marking for Shipment and Storage
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Apr. 10, 2002. Published June 2002. Originally published as F409–75. Last previous edition F409–99a.
Current edition approved Nov. 1, 2008. Published February 2009. Originally approved in 1975. Last previous edition approved in 2002 as F 409 – 02.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 08.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Annual Book of ASTM Standards, Vol 08.04.
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 194
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F409–99a Designation: F 409 – 02 (Reapproved 2008)
Standard Specification for
Thermoplastic Accessible and Replaceable Plastic Tube and
1
Tubular Fittings
This standard is issued under the fixed designation F 409; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, hydrostatic pressure, joint
integrity, and solvent cement for thermoplastic tube and fittings for accessible and replaceable domestic waste connections.
Marking requirements are also included. Plastic which does not meet the material requirements specified in Section 5 is excluded.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 618 Practice for Conditioning Plastics for Testing
D 1600 Terminology for Abbreviated Terms Relating to Plastics
D 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D 2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D 2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D 2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D 2609 Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
D 2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
D 2661 Specification forAcrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
D 2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D 3965 Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) CompoundsMaterials for Pipe and Fittings
D 4101 Specification for Propylene Plastic Polypropylene Injection and Extrusion Materials
F 402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F 412 Terminology Relating to Plastic Piping Systems
F 1498 Specification for Taper Pipe Thread 60°Threads 60 for Thermoplastic Pipe and Fittings
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.3 Military Standard:
1
This specification is under the jurisdiction ofASTM Committee F-17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on Drain,Waste,
and Vent Pipe and Tube.
Current edition approved August 10, 1999. Published September 1999. Originally published as F409–75. Last previous edition F409–99.
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Nov. 1, 2008. Published February 2009. Originally approved in 1975. Last previous edition approved in 2002 as F 409 – 02.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 08.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Annual Book of ASTM Standards, Vol 08.04.
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave.,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.