ASTM A1024/A1024M-18
(Specification)Standard Specification for Steel Line Pipe, Black, Plain-End, Seamless
Standard Specification for Steel Line Pipe, Black, Plain-End, Seamless
ABSTRACT
This specification covers standard requirements for seamless, black, plain-end steel pipes for use in the conveyance of fluids under pressure. A quantity of pipe of the same ordered diameter, heat, wall thickness, and grade shall be given. Heat and product analyses shall be performed wherein steel pipes shall conform to the required chemical composition for carbon, sulfur, and phosphorus. Steel samples shall undergo tension test and shall conform to tensile properties such as yield strength and tensile strength. Hydrostatic pressure test shall be performed for steel samples with specified wall thickness and test pressure. The entire outer surface of the steel pipe shall undergo nondestructive electric test and shall be inspected for longitudinal defects by either magnetic particle inspection, ultrasonic inspection, and electromagnetic inspection.
SCOPE
1.1 This specification covers seamless, black, plain-end steel pipe for use in the conveyance of fluids under pressure. Pipe in sizes NPS 1 to 26, inclusive, as given in ASME B36.10M is included. Pipe having other dimensions, in this size range, may be furnished provided such pipe complies with all other requirements of this specification.
1.2 It is intended that the pipe be capable of being circumferentially welded in the field when welding procedures in accordance with the requirements of the applicable pipeline construction code are used.
1.3 The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values in each system are not exact equivalents; therefore, each system is to be used independently of the other.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:A1024/A1024M −18
Standard Specification for
1
Steel Line Pipe, Black, Plain-End, Seamless
This standard is issued under the fixed designation A1024/A1024M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* A941TerminologyRelatingtoSteel,StainlessSteel,Related
Alloys, and Ferroalloys
1.1 This specification covers seamless, black, plain-end
2.2 API Standard:
steel pipe for use in the conveyance of fluids under pressure.
API RP 5L3Recommended Practice for Conducting Drop-
Pipe in sizes NPS 1 to 26, inclusive, as given in ASME
3
Weight Tear Tests on Line Pipe
B36.10M is included. Pipe having other dimensions, in this
2.3 ASME Standard:
sizerange,maybefurnishedprovidedsuchpipecomplieswith
4
ASME B36.10MWelded and SeamlessWrought Steel Pipe
all other requirements of this specification.
1.2 It is intended that the pipe be capable of being circum-
3. Terminology
ferentially welded in the field when welding procedures in
3.1 Definitions—For terminology used in this specification,
accordance with the requirements of the applicable pipeline
refer to Terminology A941.
construction code are used.
3.2 Definitions of Terms Specific to This Standard:
1.3 The values stated in either inch-pound units or in SI
3.2.1 lot, n—a quantity of pipe of the same ordered
units are to be regarded separately as standard.Within the text,
diameter, heat, wall thickness, and grade as given in Table 1.
the SI units are shown in brackets. The values in each system
3.2.2 seamless pipe, n—a tubular product made without a
are not exact equivalents; therefore, each system is to be used
welded seam; it is manufactured usually by hot working the
independently of the other.
material, and if necessary, by subsequently cold-finishing the
1.4 This international standard was developed in accor-
hot worked tubular product to produce the desired shape,
dance with internationally recognized principles on standard-
dimensions, and properties.
ization established in the Decision on Principles for the
3.2.3 specified outside diameter (OD), n—the outside diam-
Development of International Standards, Guides and Recom-
eter specified in the purchase order or the outside diameter
mendations issued by the World Trade Organization Technical
listedinASMEB36.10Mforthenominalpipesizespecifiedin
Barriers to Trade (TBT) Committee.
the purchase order.
2. Referenced Documents
4. General Requirements
2
2.1 ASTM Standards:
4.1 Pipe furnished under this specification shall conform to
A370Test Methods and Definitions for Mechanical Testing
the applicable requirements of Specification A530/A530M
of Steel Products
unless otherwise provided herein.
A450/A450MSpecification for General Requirements for
Carbon and Low Alloy Steel Tubes
5. Ordering Information
A530/A530MSpecification for General Requirements for
Specialized Carbon and Alloy Steel Pipe
5.1 Information items to be considered, if appropriate, for
A751Test Methods, Practices, and Terminology for Chemi- inclusion in the purchase order are as follows:
cal Analysis of Steel Products
5.1.1 Specification designation and year of issue,
5.1.2 Quantity (feet or metres),
5.1.3 Grade (see Table 2 and 8.1.5),
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
5.1.4 Size (either nominal (NPS) or outside diameter and
Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee
wall thickness),
A01.09 on Carbon Steel Tubular Products.
Current edition approved Nov. 1, 2018. Published November 2018. Originally
approved in 2002. Last previous edition approved in 2012 as A1024/A1024M–02
3
(2012). DOI: 10.1520/A1024_A1024M-18. Available from American Petroleum Institute (API), 1220 L. St., NW,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Washington, DC 20005-4070, http://api-ec.api.org.
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from American Society of Mechanical Engineers (ASME), ASME
Standards volume information, refer to the standard’s Document Summary page on International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
the ASTM website. www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A1024/A1024M−18
TABLE 1 Lot Size and Sample Size
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A1024/A1024M − 02 (Reapproved 2012) A1024/A1024M − 18
Standard Specification for
1
Steel Line Pipe, Black, Plain-End, Seamless
This standard is issued under the fixed designation A1024/A1024M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers seamless, black, plain-end steel pipe for use in the conveyance of fluids under pressure. Pipe in
sizes NPS 1 to 26, inclusive, as given in ASME B36.10M is included. Pipe having other dimensions, in this size range, may be
furnished provided such pipe complies with all other requirements of this specification.
1.2 It is intended that the pipe be capable of being circumferentially welded in the field when welding procedures in accordance
with the requirements of the applicable pipeline construction code are used.
1.3 The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI
units are shown in brackets. The values in each system are not exact equivalents; therefore, each system is to be used independently
of the other.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A450/A450M Specification for General Requirements for Carbon and Low Alloy Steel Tubes
A530/A530M Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
2.2 API Standard:
3
API RP 5L3 Recommended Practice for Conducting Drop-Weight Tear Tests on Line Pipe
2.3 ASME Standard:
4
ASME B36.10M Welded and Seamless Wrought Steel Pipe
3. Terminology
3.1 Definitions—For terminology used in this specification, refer to Terminology A941.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 lot, n—a quantity of pipe of the same ordered diameter, heat, wall thickness, and grade as given in Table 1.
3.2.2 seamless pipe, n—a tubular product made without a welded seam; it is manufactured usually by hot working the material,
and if necessary, by subsequently cold-finishing the hot worked tubular product to produce the desired shape, dimensions, and
properties.
3.2.3 specified outside diameter (OD), n—the outside diameter specified in the purchase order or the outside diameter listed in
ASME B36.10M for the nominal pipe size specified in the purchase order.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.09
on Carbon Steel Tubular Products.
Current edition approved Sept. 1, 2012Nov. 1, 2018. Published November 2012November 2018. Originally approved in 2002. Last previous edition approved in 20072012
as A1024/A1024M – 02 (2012).(2007), DOI: 10.1520/A1024_A1024M-02R12.10.1520/A1024_A1024M-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Petroleum Institute (API), 1220 L. St., NW, Washington, DC 20005-4070, http://api-ec.api.org.
4
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, ThreeTwo Park Ave., New York, NY 10016-5990,
http://www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A1024/A1024M − 18
TABLE 1 Lot Size and Sample Size for Mechanical and
Toughness Testing
Pipe Size Lot Size Sample Size
NPS 2 through NPS 5 400 lengths 1
NPS 6 through NPS 12 200 lengths 1
>NPS 12 100 lengths 1
4. General Requirements
4.1 Pipe furnished
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.