ASTM D2467-02
(Specification)Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
SCOPE
1.1 This specification covers poly(vinyl chloride) (PVC) Schedule 80 pipe fittings. Included are requirements for materials, workmanship, dimensions, and burst pressure.
Note 1—CPVC plastic pipe fittings, which were formerly included in this standard, are now covered in Specification F 439.
1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing.
Note 2—Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious saftey hazards should a system fail for any reason.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.
1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 2467 – 02
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
1
80
This standard is issued under the fixed designation D 2467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D 1599 Test Method for Resistance to Short-Time Hydrau-
3
lic Pressure of Plastic Pipe, Tubing, and Fittings
1.1 This specification covers poly(vinyl chloride) (PVC)
D 1600 Terminology for Abbreviated Terms Relating to
Schedule 80 pipe fittings. Included are requirements for mate-
2
Plastics
rials, workmanship, dimensions, and burst pressure.
D 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
NOTE 1—CPVC plastic pipe fittings, which were formerly included in
Compounds and Chlorinated Poly(Vinyl Chloride)
this standard, are now covered in Specification F 439.
2
(CPVC) Compounds
1.2 The products covered by this specification are intended
D 1785 Specification for Poly(Vinyl Chloride) (PVC) Plas-
3
for use with the distribution of pressurized liquids only, which
tic Pipe, Schedules 40, 80, and 120
are chemically compatible with the piping materials. Due to
D 2122 Test Method for Determining Dimensions of Ther-
3
inherent hazards associated with testing components and sys-
moplastic Pipe and Fittings
3
tems with compressed air or other compressed gases some
D 2749 Symbols for Dimensions of Plastic Pipe Fittings
3
manufacturers do not allow pneumatic testing of their products.
F 412 Terminology Relating to Plastic Piping Systems
Consult with specific product/component manufacturers for
F 439 Specification for Socket-Type Chlorinated Poly (Vi-
3
their specific testing procedures prior to pneumatic testing.
nyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
F 1498 Specification for Taper Pipe Threads 60° for Ther-
NOTE 2—Pressurized (compressed) air or other compressed gases
3
moplastic Pipe and Fittings
contain large amounts of stored energy which present serious saftey
2.2 Federal Standard:
hazards should a system fail for any reason.
4
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
1.3 The text of this specification references notes, footnotes,
2.3 National Sanitation Foundation Standard:
and appendixes which provide explanatory material. These
Standard No. 14 for Plastic Piping Components and Related
notes and footnotes (excluding those in tables and figures) shall
5
Materials
not be considered as requirements of this specification.
Standard No. 61 for Drinking Water Systems
1.4 The values stated in inch-pound units are to be regarded
5
Components—Health Effects
as the standard. The values given in parentheses are provided
for information only.
3. Terminology
1.5 The following safety hazards caveat pertains only to the
3.1 General—Definitions are in accordance with Terminol-
test method portion, Section 8, of this specification. This
ogy F 412 and abbreviations are in accordance with Teminol-
standard does not purport to address all of the safety concerns,
ogy D 1600, unless otherwise indicated. The abbreviation for
if any, associated with its use. It is the responsibility of the user
poly(vinyl chloride) plastic is PVC.
of this standard to establish appropriate safety and health
practices and determine the applicability of regulatory limita-
4. Classification
tions prior to use.
4.1 General—This specification covers Schedule 80 PVC
pipe fittings, socket-type, made from four PVC plastic com-
2. Referenced Documents
pounds and intended for use with Iron Pipe Size (IPS)
2.1 ASTM Standards:
2 outside-diameter plastic pipe.
D 618 Practice for Conditioning Plastics for Testing
1 3
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Annual Book of ASTM Standards, Vol 08.04.
4
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700
Current edition approved Sept. 10, 2002. Published September 2002. Originally Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
5
published as D 2467 – 65 T. Last previous edition D 2467 – 01. Available from the National Sanitation Foundation, P.O. Box 1468, Ann Arbor,
2
Annual Book of ASTM Standards, Vol 08.01. MI 48106.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D 2467 – 02
4.1.1 Fittings covered by this specification are normally 7. Workmanship, Finish, and Appearance
molded.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.