ASTM F409-17

Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

ABSTRACT
This specification covers the material, dimensional ,and performance requirements and associated test methods for thermoplastic tubes and fittings for accessible and replaceable domestic waste connections. The tubes, fittings and mechanical joint components shall be made of either virgin acrylonitrile-butadiene-styrene (ABS) plastic, virgin poly(vinyl chloride) (PVC) plastic, or virgin polypropylene plastic. When evaluated by the test procedures provided herein, the products shall adhere to requirements stipulated for hydrostatic pressure, axial stress, joint integrity, and solvent cement.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, hydrostatic pressure, joint integrity, and solvent cement for thermoplastic tube and fittings for accessible and replaceable domestic waste connections. Marking requirements are also included. Thermoplastic that does not meet the material requirements specified in Section 5 is excluded.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Mar-2017
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.63 - DWV

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F409 −17 An American National Standard
Standard Specification for
Thermoplastic Accessible and Replaceable Plastic Tube and
1
Tubular Fittings
ThisstandardisissuedunderthefixeddesignationF409;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D1600 TerminologyforAbbreviatedTermsRelatingtoPlas-
tics
1.1 This specification covers requirements and test methods
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
for materials, dimensions and tolerances, hydrostatic pressure,
Compounds and Chlorinated Poly(Vinyl Chloride)
joint integrity, and solvent cement for thermoplastic tube and
(CPVC) Compounds
fittings for accessible and replaceable domestic waste connec-
D2122 Test Method for Determining Dimensions of Ther-
tions. Marking requirements are also included. Thermoplastic
moplastic Pipe and Fittings
that does not meet the material requirements specified in
D2235 Specification for Solvent Cement for Acrylonitrile-
Section 5 is excluded.
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
1.2 Thetextofthisspecificationreferencesnotes,footnotes,
D2564 Specification for Solvent Cements for Poly(Vinyl
and appendixes which provide explanatory material. These
Chloride) (PVC) Plastic Piping Systems
notesandfootnotes(excludingthoseintablesandfigures)shall
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe
not be considered as requirements of the specification.
and Fittings
1.3 Units—The values stated in inch-pound units are to be
D2661 Specification for Acrylonitrile-Butadiene-Styrene
regarded as standard. The values given in parentheses are
(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe
mathematical conversions to SI units that are provided for
and Fittings
information only and are not considered standard.
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic
Drain, Waste, and Vent Pipe and Fittings
1.4 The following safety hazards caveat pertains only to the
test methods portion, Section 8, of this specification: This D3965 ClassificationSystemandBasisforSpecificationsfor
standard does not purport to address all of the safety concerns, Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials
if any, associated with its use. It is the responsibility of the user for Pipe and Fittings
of this standard to establish appropriate safety, health, and
D4101 Classification System and Basis for Specification for
environmental practices and determine the applicability of
Polypropylene Injection and Extrusion Materials
regulatory limitations prior to use.
F402 Practice for Safe Handling of Solvent Cements,
1.5 This international standard was developed in accor-
Primers, and Cleaners Used for Joining Thermoplastic
dance with internationally recognized principles on standard-
Pipe and Fittings
ization established in the Decision on Principles for the
F412 Terminology Relating to Plastic Piping Systems
Development of International Standards, Guides and Recom-
F1498 Specification forTaper PipeThreads 60° forThermo-
mendations issued by the World Trade Organization Technical
plastic Pipe and Fittings
Barriers to Trade (TBT) Committee.
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2. Referenced Documents
2
2.3 Military Standard:
2.1 ASTM Standards:
3
MIL-STD-129 Marking for Shipment and Storage
D618 Practice for Conditioning Plastics for Testing
2.4 ASME Standard:
4
B1.20.1 Pipe Threads, General Purpose (Inch)
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved April 1, 2017. Published May 2017. Originally
approved in 1975. Last previous edition approved in 2012 as F409 – 12. DOI:
3
10.1520/F0409-17. Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
4
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from American Society of Mechanical Engineers (ASME), ASME
Standards volume information, refer to the standard’s Document Summary page on International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
the ASTM website. www.asme.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F409−17
TABLE 1 Dimensions and Tolerances for Outside Diameters and Thickness of Plastic Tube
Outs
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F409 − 12 F409 − 17 An American National Standard
Standard Specification for
Thermoplastic Accessible and Replaceable Plastic Tube and
1
Tubular Fittings
This standard is issued under the fixed designation F409; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope Scope*
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, hydrostatic pressure, joint
integrity, and solvent cement for thermoplastic tube and fittings for accessible and replaceable domestic waste connections.
Marking requirements are also included. Plastic whichThermoplastic that does not meet the material requirements specified in
Section 5 is excluded.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are
mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification:This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2609 Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
D2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
D2661 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D3965 Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe
and Fittings
D4101 Specification for Polypropylene Injection and Extrusion Materials
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
F1498 Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Aug. 1, 2012April 1, 2017. Published November 2012May 2017. Originally approved in 1975. Last previous edition approved in 20082012 as
F409 – 08.F409 – 12. DOI: 10.1520/F0409-12.10.1520/F0409-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F409 − 17
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Age
...